-
Product
Fixed Probe Temperature / RH
S.TO1 / S.TO2
-
Fixed horizontal interchangeable temperature and humidity probes with SICRAM 2 module for active transmitters, humidity and temperature regulators series HD2717T and HD2817T.
-
Product
Ultra High 6.70 (190.00) - 11.80 (335.00) General Purpose Probe
EPA-4G-2
-
Current Rating (Amps): 7Average Probe Resistance (mOhm): 35Test Center (mil): 187Test Center (mm): 4.75Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 1,320Overall Length (mm): 33.53
-
Product
Insulation Resistance Tester For PV (Judge Deterioration Point)
MIS-PVS
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The model MIS-PVS is an insulation resistance tester for the exclusive use in photovoltaic systems. The ordinary insulation resistance testers cannot make measurement properly during generation of PV systems. This instrument, however, can measure the insulation resistance simply by touching probe to the live line whether making generation or not. There are two ranges of PVH and PVL. PVH is for high voltage generation system (more than 500V and less than 1000V) and PVL is for the system less than 500V.
-
Product
Extendible Test Leads
-
The Extendable Tip Probe permits testing in those hard to reach areas. The tips are fully insulated with durable Kynar. This prevents accidental shorting of adjacent components. The tip is stainless steel and is very sharp, allowing for penetration of conformal coatings. The rubber lead is 18 gauge, 48" long.
-
Product
Rogowski AC Current Probe
RCP500
-
Shenzhen Micsig Instruments Co., Ltd.
Adopts the Rogowski coil current measurement system: within the range, the output signal of the system and the current signal to be measured are always linear, so the accuracy will not change with the current; The RCP500 measures AC current up to 500A pk, minimum to 200mA pk, with bandwidth ranging from 15Hz to 300KHz, 1% accuracy, and has less than 2mV noise. Directly powered by Micsig UPI interface, realise auto scaling setup,
-
Product
Conductivity Type (P/N) Checker By Contact Thermo-electromotive Force Method (seebek Effect)
PN-12α
-
*Thermo electrode and cold electrode is mounted detecting part of measuring probes*Possible to check most figure of sample such as single crystalline silicon wafer, bulk, ingot and so on*Please select from 2 types;1) 2 probe ver.(Hot probe, Cold probe),2) 1 probe ver.(Hot & Cold probe)
-
Product
Rail Wheel Testing Using Phased Array System
ECHOMAC® PA Wheel Tester
-
MAC introduces two versions of Rail Wheel Testers using ECHOMAC® PA platform based on customer requirements. One is a semi-automated solution using local immersion technique. Used for tread inspection of new and/or reprofiled wheels. This solution meets or exceeds EN13262, ISO5948 or AAR M-107/M-208 standards for tread inspection. The second solution is a fully automated immersion tank. Performs tread and face inspection of rail wheels using two phased array probes simultaneously. This solution meets or exceeds EN13262, ISO5948 or AAR M-107/M-208 standards for tread and face inspection, while monitoring the backwall on the face side per EN 13262.
-
Product
EMCTD Broadband RF Safety Systems
-
The EMCTD analog Smart Fieldmeter® is easy to read and to operate. The EMCTD broadband electromagnetic probe covers the 0.2 to 3000 MHz spectrum where most common industrial, communications, medical and government RF emitters are found. The ANGPE-3000 system enables checking of home, office, and workplace RF levels. The system is designed to conveniently measure RF levels around WiFi access points, RFID systems and rooftop antennas; to find transmitter cabinet radiation, locate transmission line leaks, to identify non-radiating antenna elements, and much more. With the supplied NIST-traceable calibration, this system supports laboratory testing of RF devices in compliance with present EMC and RF safety standards.
-
Product
Premium 4.49 (127.00) - 12.00 (340.00) High Performance Lead Free Probe
LFRE-25I40-12
-
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Isolation Probe
SE-6000/6010
-
Performs waveform measurements with high resolutions and in safe manner under high voltage environment in systems that isolate Input/output terminals through optical insulation
-
Product
Short Test Pin Probe
Probe 13
-
Shenzhen Chuangxin Instruments Co., Ltd.
Short Test Pin Probe 13 The model CX-13 short Test Pin Probe is used to test for accessibility of small objects and meets IEC, CSA and UL requirements.
-
Product
Fully Automatic Eddy Current Crack Test System
ROTO-SCAN
-
Foerster Instruments, Incorporated
The fully automatic crack test system ROTO-SCAN was specially developed for the testing of rings. The mechanical equipment has been developed for the gentlest possible handling of the test pieces and features a compact and low-maintenance design. The test probes seamlessly scan the inner and outer contours of the test pieces, thus ensuring 100 % testing of the rings.
-
-
Product
Probes For Non-Contact Ultrasonic Testing
SONOSCAN CFC / CF
-
Due to the strong damping properties of air, low frequencies in the kHz range are used in air-coupled ultrasonic testing. It is therefore all the more important that the ultrasonic transducers offer a particularly high sensitivity in order to ensure high penetration and improved resolution. We achieve this, among other things, by installing preamplifiers in the receiver probe as well as by using our own Piezocomposite Technology, which enables a flexible use of the matching materials in our CFC and CF probes.
-
Product
HPA-52 General Purpose Probes
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 75Full Travel (mm): 1.91Recommended Travel (mil): 75Recommended Travel (mm): 1.91Mechanical Life (no of cyles): 250,000Overall Length (mil): 629Overall Length (mm): 15.98
-
Product
Test Service Offerings
-
ASE Industrial Holding Co., Ltd.
ASE provides a complete range of semiconductor testing services to our customers, including front-end engineering testing, wafer probing, final testing of logic, mixed signal, and memory semiconductors, and other test-related services. Our testing services employ technology and expertise that are among the most advanced in the semiconductor industry.
-
Product
Compact TLP/VF-TLP/HMM Probearm Set for Temperature Measurements
PHD-4001A
-
High Power Pulse Instruments GmbH
*Electrically isolated probearm kit for VF-TLP, TLP, HMM, HBM force and sense probingbased on the GGB Picoprobe Model 10 replacement probe tips*Buried coaxial cable channel for thermo-chuck in isolated chamber temperature measurements*Compatible with GGB Picoprobe Model 10 replacement probetips*Compatible with all standard micropositioner interfaces*High precision rotation of the probearm by backlash-free 80:1 gear*Rugged stainless steel design*SMA connectors
-
Product
Induction Style Control Relay
1500
-
A floatless liquid level control system from B/W Controls consists of a relay of the proper type, a holder designed to support one or more electrodes or probes in the liquid container, and the corrosion resistant electrodes themselves.
-
Product
Standard 1.50 (43.00) - 4.00 (113.00) High Performance Lead Free Probe
LFRE-25L36-4
-
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Ultra Low Noise Preamp
J2180A
-
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
Product
Passive Probe, 500 MHz, 2.5mm Tip
PP007-WR-1
-
The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day.The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed—important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes.
-
Product
4 GHz, 20 GS/s, 4ch, 100 Mpts/Ch High Definition Mixed Signal Oscilloscope
WavePro 404HD-MS
-
HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s.Up to 5 Gpts of acquisition memory enables detailed viewing of long events.15.6" 1900 x 1080 Full HD capacitive touchscreen.New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector.MAUI with OneTouch user interface for intuitive and efficient operation.Deep toolbox enables and simplifies complex analysis.Intuitive navigation to quickly find important features in long waveforms.Zone Trigger – Simple Triggering for Complex Signals.
-
Product
Quick Change Probes For Weld Seam Testing (ASTM)
SONOSCAN Q
-
In addition to angle beam probes according to european standards (EN), we offer probes with quick-change wedges for ultrasonic weld seam inspection as well as various wedges for the american market. Quick-change probes are used wherever access to the inspection object is difficult to reach with the larger AWS transducers. The relatively small, round elements also offer better defect resolution.
-
Product
Standard 1.53 (43.00) - 4.00 (113.00) High Performance Lead Free Probe
LFRE-72I-4
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,700Overall Length (mm): 43.18
-
Product
Standard 1.53 (43.00) - 4.00 (113.00) High Performance Lead Free Probe
LFRE-72U-4
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,700Overall Length (mm): 43.18
-
Product
Light 0.75 (21.00) - 2.00 (57.00) Bead Probe
BTP-25HL-2
-
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Spring loaded type sample mounting board
SPCB
-
Mount samples on SPCB board without bonding wires.Spring loaded clamps helps to move probe pin easily x, y, z direction.Gold plated Non-magnetic phosphor-bronze constructionContacts on sample’s four point corner by soldering materials, such as InSn may still be required for good ohmic contact.
-
Product
Standard 0.80 (22.00) - 4.00 (114.00) High Frequency Probe
CSP-03G-003
-
Current Rating (Amps): 6Bandwidth @ -1dB (GHz): 3.70Return Loss @ -20dB (GHz): 1.80Nominal Impedance (Ohms): 50Dielectric VTE Rating (k VAC): 1Test Center (mil): 300Test Center (mm): 7.62Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Overall Length (mil): 1,090Overall Length (mm): 27.76
-
Product
Exhaust Gas Temperature Thermocouple
LM6000 T4.8
-
The latest and most capable LM6000 gas turbine exhaust gas temperature (EGT) probe from AMETEK offers the longest possible life. AMETEK is the original EGT probe supplier for CF6 aircraft engines. LM2500, LM5000, and LM6000 industrial gas turbines and now brings to market an EGT probe with new materials and a new design. The latest LM6000 T4.8 EGT thermocouple is OEM qualified and incorporates, many improvements over any previous products. Materials are carefully selected to ensure long product life and superior performance. Specifically, a new single crystal alloy for the probe support significantly improves high temperature mechanical strength. In addition, the thermocouple sheath material increases high temperature oxidation and creep resistance. Best of all, AMETEK's new T4.8 thermocouple is completely interchangeable so that it can be used on all LM6000 applications.
-
Product
InfiniiMode Active Differential Probe, 1.5 GHz
N2750A
-
The N2750A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2750A probe’s InfiniiMode provides the following modes of operation.
