-
Product
Probes
70 Series
-
American Probe & Technologies, Inc.
The series is for all probes that are non-standard in shank diameter (other than 10 or 20 mil).
-
Product
Microwave Probes
D-Probe
-
With only two signal pins, D-Probes can perform accurate measurements without the need of nearby ground pads.
-
Product
Scanning Probes
-
Scanning probes can acquire several hundred surface points each second, enabling measurement of form as well as size and position.
-
Product
Probes
Type K
-
No matter the application, ThermoWorks has a probe for you: penetration probes, immersion probes, air probes, surface probes, wire probes, even specialized probes like griddle probes, burger probes, pipe clamp probes, and probes for medical and lab use. Choose from standard tip, reduced tip, corkscrew tip, alligator clip, or needle probes; different handle types; and straight, coiled, stainless overbraid or even armored cables. Sensor types include type T or type K thermocouples, RTD sensors and our Pro-Series® line of thermistor probes.
-
Product
Sanitary Probes
-
Used in the food, beverage, dairy, and pharmaceutical industries, these hygienic/sanitary probes carry 3-A certification, which is required in these sanitary, wash down, & clean-in-place applications.
-
Product
USB Hall Probes
-
MAGNET-PHYSIK Dr. Steingroever GmbH
The USB Hall probe is simply connected to a computer and operated using easy-to-understand software. No additional measuring device is required to measure the magnetic field strength. You can download the "USB Teslameter" software for Windows here. A Linux version is available from us on request.
-
Product
USB Oscilloscope Probes
-
High-performance, passive accessories designed for use with their PC-based oscilloscopes.
-
Product
SSP Switch Probes
Switch Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Spring Force Remark: Force at switch point: 2.36 (66)Test Center (mil): 187Test Center (mm): 4.75Full Travel (mil): 150Full Travel (mm): 3.81Recommended Travel (mil): 100Recommended Travel (mm): 2.54Mechanical Life (no of cyles): 100,000Overall Length (mil): 1,210Overall Length (mm): 30.73Switch Point (mil): 25Switch Point (mm): 0.64
-
Product
Electrical Resistance Probes
-
Electrical resistance (ER) corrosion probes are commonly used in petroleum, chemical processing, and other environments where on-line corrosion rate readings are required. Whereas test coupons must be removed from the process for evaluation, corrosion probes can allow corrosion rate determination without probe removal.
-
Product
BondMaster Probes
-
Please note that product availability varies by region. Contact your local Olympus sales office for more information.
-
Product
Near Field Probes
-
Anteral has extensive background in the design of Near Field Probes (open ended waveguides probes). Our Near Field Probes are currently being used in several laboratories around the world including the ESA's anechoic chamber. Anteral designs Near Field Probes from 10 GHz to 750 GHz covering the sectors requirements. Moreover, our Near Field Probes have a sharped design minimize reflections.
-
Product
Renishaw Scanning Probes
-
Advanced Industrial Measurement Systems
The REVO® is designed to maximize CMM throughput while maintaining high system accuracy and uses synchronized motion as well as Renscan5 measurement technology to minimize the dynamic effects of CMM motion at ultra high measurement speeds. This is achieved by letting the REVO® head do the fast demanding motion while the CMM moves in a slow linear fashion.
-
Product
Logic Analyzer Probes
-
Three probe types are available for GoLogicXL logic analyzers: flying leadset, Mictor, and Pinpoint probes. The Mictor and Pinpoint probes are compatible with similar Keysight/Agilent "soft touch" and Tektronix "connectorless" probes. All GoLogicXL probes are coaxially shielded and use passive termination inputs to prevent loading the device under test. Both differential and single-ended input signals are supported by all probes. Input voltage swings small as 300 mV are supported in single-ended mode, and 150 mV for differential signals.
-
Product
Probes Conductivity
-
In-line sensors that measure a solution's ability to conduct electricity.
-
Product
Test Probes
-
A physical device used to connect electronic test equipment to a device under test (DUT).
-
Product
High Current Probes
High Current Probe
*Low internal resistance to minimize arching*PogoPlus bias ball design*High current optimized base material and plating*Higher temperature spring design*Specialized high current tip geometry
-
Product
SMD Test Probes
-
The Parrot Clip, model PCM W1 or PCS-MB W1 invention can be connected to resistance’s, diodes, integrated circuits (SOIC, SO) etcThe advantage of the Parrot Clip is given by the double metal connection made between the new metal tip and the steel hooked rod, spring loaded. This connection, being made by metal parts is electrical and mechanical reliable, even if the contact point are small. Connections are resistant even at high temperatures.
-
Product
EMC Near Field Probes
TBPS01
-
The TBPS01 EMC near field probes H20, H10, H5 and E5 are magnetic field (H) and electric field (E) probes for radiated emissions EMC pre-compliance measurements. The probes are used in the near field of sources of electromagnetic radiation.
-
Product
Differential Pressure Probes
PP473-S…
-
Differential pressure probes complete with SICRAM module to measure pressure in the range 10, …, 2000 mbar.
-
Product
Probes, Magnetic Field
EM-6881 | 480 KHz To 30 MHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
Product
Probes & Test Leads
-
The Di-LOG range to test leads are designed and manufactured to the highest quality and meet all safety standard as stipulated in BS EN 61010
-
Product
Test Probes
-
Test Probes provide the vital link to transfer measurement signals as true and as undistorted as possible. Therefore these elements can be regarded as the heart of Test Fixtures – and for this very reason it is important for Equip-Test to offer high performance Test Probes with best quality and value, and thus ensure maximized ROI (Return of Investment) for our customers. Test Probes supplied by Equip-Test always provide the best-possible available solution for your contacting demands.
-
Product
F-S General Purpose Probes
General Purpose Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 66Recommended Travel (mm): 1.68Overall Length (mil): 780Overall Length (mm): 19.81Rec. Mounting Hole Size (mil): 86Rec. Mounting Hole Size (mm): 2.18Recommended Drill Size: #44
-
Product
Flexible Magnetic Field Probes
-
Projekt Elektronik Mess- und Regelungstechnik GmbH
The active probes are equipped with active amplifier electronics and have an extremely low-impedance output, ie they can also drive long lines. The output signal is calibrated according to specification. They can not only be connected to a certain type of teslameter, but can also be connected to any signal input.
-
Product
Energy Probes
RjP-600 Series
-
The RjP-600 Series energy probes integrate the detector and preamplifier in the same enclosure, thereby maximizing signal integrity between the detector and preamplifier. This permits longer cable runs between the probe and instrument, as is often necessary in production environments. Probe specific information, like calibration date and wavelength response curves, is stored in the probe for access by the instrument. Other features include interchangeable filter holders and ¼-20 mounting hole.
-
Product
Kelvin Contact Spring Probes
-
We have spring probes for Kelvin contact, which best suits to use for sensitive and extremely precise test. It is used by contacting to one terminal of semiconductor by two probes. We have 0.3, 0.4 and 0.5mm pitch probe for Kelvin contact.
-
-
Product
Probes
-
measures relative pressure range from -1 to 60 bar and -14 to 870 psi and comes with wireless connection low energy.
-
Product
Oscilloscope Probes and Accessories
-
Teledyne LeCroy has a wide variety of world class probes and amplifiers to complement its product line. From the ZS high impedance active probes to the DH Series Differential High-bandwidth Probes which offers bandwidths up to 30 GHz, Teledyne LeCroy probes and probe accessories provide optimum mechanical connections for signal measurement.
-
Product
Probes & Flow Cells
-
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
