Product

MOD MONITOR

TYPE HFX-1

-

National RF, Inc

TYPE HFX-1 - National RF, Inc

The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.

Product

Test Contactor/WLCSP Probe Head

ACE

-

Cohu, Inc.

ACE - Cohu, Inc.

ACE™ test sockets offer optimal RF performance for fine pitch FBGA, QFN and wafer-level packages for Power Amplifiers, RF switches and mobile communications. Supporting pitches down to 0.4 mm, ACE features an innovative design that provides superior performance, improved yields and power efficiency.ACE probe heads deliver exceptional electrical performance, both DC and RF. Manufactured from HyperCore™ base material, a proprietary material of Cohu’s Everett Charles Technologies, ACE probes have the electrical properties of BeCu with the non-oxidizing properties of a precious metal. The short signal path, sharp tips, and large contact area between plungers provide high current conductance and reliable contact with less force.

Product

RH+T+Tdp Cable Probe

T3111-2

-

COMET SYSTEM, s.r.o.

T3111-2 - COMET SYSTEM, s.r.o.

Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.

Product

Interchangeable Temperature Humidity Probes

S.TC series

-

Senseca

S.TC series - Senseca

Interchangeable temperature and humidity probes with SICRAM 2 module and with cable for the HD2717T… and the HD2817T… transmitters series.

Product

Automated Tester

-

Mycronic

Mycronic

With high labor costs in Europe and the US, and the surge in labor cost in Asia, automated test solutions are in demand. Automated systems also improve traceability and reduce operator mistakes.The combination of automation with high throughput test systems is perfect to extend the usage of Flying Probe Testers to mid size production/sample volumes.

Product

Kelvin Test Probes

-

Equip-Test Kft.

Equip-Test Kft.

*4 Wire measurement *Industrial Solution *Easy integration

Product

K Thermocouple Penetration Probe

TP659

-

Senseca

TP659 - Senseca

“K” Type thermocouple penetration probe. Tolerance according to IEC 60584-2 standard.

Product

Test Service Offerings

-

ASE Industrial Holding Co., Ltd.

ASE Industrial Holding Co., Ltd.

ASE provides a complete range of semiconductor testing services to our customers, including front-end engineering testing, wafer probing, final testing of logic, mixed signal, and memory semiconductors, and other test-related services. Our testing services employ technology and expertise that are among the most advanced in the semiconductor industry.

Product

Straight Wire Porbe Pins

Buckling Beam

-

Prospect Products Inc.

Buckling Beam - Prospect Products Inc.

Straight wire probe pins are a proven solution for various electronics production test environments.

Product

Single Sheet Tester

Model SST500X500

-

Gopal Electronics

Model SST500X500 - Gopal Electronics

Gopal Make single sheet tester SST is developed as per IEC 60404-3. It can be attached as probe to Ep400 Main unit and user can test specific total loss, specific apparent power, and r.m.s value of magnetic field strength as well as B/h curve in the software.

Product

Test Thorn Probe

CX-41

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-41 - Shenzhen Chuangxin Instruments Co., Ltd.

Test Thorn Probe For testing accessibility in appliances with visibly glowing heating elements.

Product

Ultrasonic Thickness Gauge

TI-45 Series

-

JFE Advantech Co., Ltd.

TI-45 Series - JFE Advantech Co., Ltd.

You can instantly measure the thickness of a material simply by positioning a probe. This innovative gauge is widely used and is capable of measuring a variety of materials including iron, stainless steel, glass and ceramics.

Product

Scanner Probe

RFS set

-

Langer EMV-Technik GmbH

RFS set - Langer EMV-Technik GmbH

The RFS set consits of three passive near field probes designed for the use in a measurement scanner during the development of E-field and magnetic field. They are designed for frequency ranges of 30 MHz to 3 GHz. The probe heads of the RFS set allow for close measurements needed to correctly localize interference sources on an electronic assembly. They document the whole image of the device under test`s near field. The scanner probes have a sheath current attenuation and are electrically shielded. They are connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance. The measuring signal can be increased with PA 203 or PA 303 preamplifier. On request RFS, LFS and XFS scanner probes can be produced.

Product

1.5 GHz, 1 MΩ, 0.9 pF Active Probe

ZS1500

-

Teledyne LeCroy

ZS1500 - Teledyne LeCroy

Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1500 is ideal for 1 GHz and lower oscilloscopes.

Product

Clamp Meter

-

Shenzhen Graigar Technology Co.,Ltd.

Shenzhen Graigar Technology Co.,Ltd.

A clamp meter is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.

Product

Globe Temperature Probe

TP3276

-

Senseca

TP3276 - Senseca

Globe temperature probe, Pt100 sensor with globe Ø 50 mm. Stem Ø 8 mm, length 110 mm. Cable length 2 metres. Equipped with SICRAM module.

Product

Data Logging Kit

ThermoVault

-

MadgeTech, Inc

ThermoVault - MadgeTech, Inc

Oven Temperature Profiling kit. Comes with TC101A Thermocouple based Temperature Data Logger with screw terminal, Thermally insulated enclosure, and Type K thermocouple probe.

Product

K Thermocouple Immersion Probe

TP741

-

Senseca

TP741 - Senseca

Immersion "K" Type thermocouple probe. Stem diameter 1,5 mm.

Product

Sub-Micron Probe Positioner

QP150 Series

-

Quarter Research and Development

QP150 Series - Quarter Research and Development

Quater’s new QP150 sub-micron probe positioners are designed to significantly reduce mechanical crosstalk between axes resulting in fast and accurately placed probe touchdowns with zero pad or trace damage from unwanted needle deflections. Overall ergonomic design places micrometers within a compact zone allowing users to precisely control needle direction and speed.

Product

Volt Probe & Socket Testers

Non-Contact & Socket

-

Amprobe Test Tools

Non-Contact & Socket - Amprobe Test Tools

Use Amprobe non-contact volt probes to safely check circuit breakers, wall sockets and fuses for voltage presence with portable, economical tools. For sockets, choose an Amprobe socket tester, which can confirm whether GFCI breakers are properly wired.

Product

Esophageal Probe

ESO-1

-

Physitemp Instruments

ESO-1 - Physitemp Instruments

The ESO-1 Esophageal/Rectal Probe for humans and larger animals. Flexible vinyl covered, soft tipped. 5 foot lead (can be made longer), 7/32'' max. tip diameter, lead diameter 1/8''. Time constant 5.0 seconds.

Product

500 MHz Passive Probe for HDO4000, 10:1, 10 MOhm

PP018-1

-

Teledyne LeCroy

PP018-1 - Teledyne LeCroy

Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.