Test Adapters
See Also: Interface Test Adapters
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2x68 Female VHDCI Connectors
510150126
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Female VHDCI Connectors
-
Product
Environmental Control System Test Platform
Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
NI Semiconductor Test Systems
Test System
The STS delivers the openness and flexibility of the NI PXI platform to the semiconductor production environment. For easy integration into the production test cell, the STS comes with features such as handler/prober integration, spring probe device under test interfacing, STDF data reporting, and system calibration.
-
Product
Adapter, 50 Ohm Type-N (f) to 75 Ohm Type-N (m), DC to 3 GHz
11852B
Coax Adapter
The Keysight 11852B is an instrument-grade, 50-ohm type-N female to 75-ohm type-N male adapter. This product is also available in a 50-ohm type-N male to 75-ohm type-N female configuration. The 11852B Option 004 has a 50 Ohm Type-N (m) and 75 Ohm Type-N (f) connector.
-
Product
PCB Adapter, ITA, SIM, VTAC, 16 Pos, 5 Slot, to (1) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1)
510171104
PCB Adapter (ITA)
A small, modular PCB board that connects high speed data inserts (VTAC) to a single USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) connector. Great for COTS cable configurations. Compatible with all VTAC/SIM ITA modules.
-
Product
EBIRST 200-pin LFH Coaxial Adapter - 56 SMBs
93-002-202
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
PCB Adapter, Receiver, TriPaddle, 96 Position, To PCB-Mounted 1x96 Male DIN 41612 Connector
510104139
PCB Adapter
The 96 Pin Signal receiver module is made from Ryton R-7, withstanding temperatures up to 220°C. Nomenclature is molded on the module.
-
Product
Multiple Module Serial Bus Test Instrument
Bi4-Series
Test Instrument
The wide variety of serial buses used in defense and aerospace applications typically requires multiple single-purpose instruments. Too often, they are difficult to reconfigure in order to test a different application.The Bi4-Series provides all the capabilities needed for complete communications bus access test for up to four serial buses used in board level (SRA/SRU) and box level (WRA/LRU) equipment—all in a single VXI module.The instrument includes test applications, industry-compliant software drivers and hardware enabling straightforward integration into automatic test systems.With the configuration flexibility needed to effectively test every bus format used in defense and aerospace applications, the Bi4-Series instrument plays a key role in reducing implementation time and test system cost.
-
Product
ARINC 818 Tester
Test Platform
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
Product
H(3)TRB & HTGB Test Systems
Test System
SET offers two H(3)TRB and HTGB product lines which differ in the number of test object channels and the range of technical possibilities. The innovative systems are scalable, modular and standardized.
-
Product
Adapter, 1.0 Mm (f) To 1.0 Mm (f), DC To 120 GHz
Y1910B
Coax Adapter
Y1910B Adapter, 1.0 mm (f) to 1.0 mm (f), DC to 120 GHz provides measurement accuracy, versatility, and ease of use for on-wafer and coaxial measurements.
-
Product
Adapter, 2.4 mm (f) to 3.5 mm (m), DC to 26.5 GHz
11901D
Coax Adapter
The Keysight 11901D is a metrology grade, 2.4 mm female to 3.5 mm male adapter with dc to 26.5 GHz operation.
-
Product
PCIe 5.0 Test Platform
PXP-500A
Test Platform
The Teledyne LeCroy PXP-500A Test Platform provides a convenient means for testing PCIe 5.0 cards with a self-contained portable and powered passive backplane. The PXP-500A provides power required for both cards under test.
-
Product
Memory Test System
T5801
Test System
Capable of Testing Ultra-High-Speed DRAM Devices, Supporting Next-Generation GDDR7, LPDDR6, and DDR6 Technologies
-
Product
6TL24 Combinational Base Test Platform
H71002400
Test Platform
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
Product
LitePoint RF Test System
J750
Test System
The option of adding LitePoint instrumentation to the J750 system delivers a cost-effective, complete production test solution covering global wireless connectivity standards.
-
Product
NI's Wireless Connectivity Functional Test Solution
Functional Test
The proliferation of wireless functionality in electronic devices is pressuring test developers to deliver more complex testers within shrinking project schedules. Evolving standards and the integration of multiple wireless technologies into new product designs mean developers must prioritize measurement speed and quality to maintain throughput and yield targets. For a solution to meet these sorts of demands, it must:
-
Product
Memory Test System
T5230
Test System
T5230 memory test system for NAND/NVM devices adopts a combined array architecture to achieve best-in-class cost-of-test performance for wafer test, including wafer-level burn-in (WLBI) and built-in self-test (BIST). The system can perform on-wafer test of 1,024 memory devices per test head in parallel, delivering high productivity and enabling floor space savings of up to 86%. Multiple test cells are connected per system controller in the T5230, allowing independent wafer test of each test cell. The test cells can be stored in a general multi-wafer prober while minimizing the test cell floor space, and the tester can be docked with probers in both linear and multi-stack configurations. For functional tests at a maximum test rate of 125MHz/250Mbps, the T5230 assures high timing accuracy, repeatability, and failure detection capability.
-
Product
OTP-Based Test System
Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
Product
PCI Express 5.0 Test Platform
Test Platform
Teledyne LeCroy’s PCI Express 5.0 Test Platform is part of a suite of tools that facilitates complete protocol testing of PCI Express devices up to and including version 5.0. The latest feature of the Teledyne LeCroy Test Platform is the addition of an integrated interposer, which eliminates the need for an external interposer. This innovation simplifies setup with fewer connection points and outboard devices, making analysis easier and more reliable than ever. In addition to using the Test Platform with the Exerciser, the user can connect two of their own devices and use the Test Platform as a PCIe 5.0 backplane and as an interposer to capture protocol traffic between the systems.
-
Product
Build-to-Print for Test Systems
Test System
Built-to-print / test system replication addresses your internal capacity and capability constraints. Ball Systems has perfected quoting, procurement, planning, assembly, testing, quality, delivery and installation to ensure your testers are on-time and on-budget, and meet design and production standards while keeping open and transparent communication.
-
Product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
Test Fixture
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
Product
Attenuator Interconnect Kit, 2.4 mm
11716F
Interconnect Adapter
The 11716F attenuator interconnection kit provides the necessary parts to connect 84904/8M and 84904/6L programmable step attenuators in series.
-
Product
RF-Antenna Communication Links Functional Test
Functional Test
The application encompasses functional tests of very large quantities of automotive antenna amplifiers, plus parallelization of tests by implementing several test stations in a rotary indexing table. The DUTs are inserted manually and after final assembly, they are loaded into the rotary table; this requires manual triggering by the operator.
-
Product
Adapter, 1.0 mm (f) to 1.0 mm (f), DC to 110 GHz
11920B
Coax Adapter
The Keysight 11920B precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms and frequency range from dc to 110 GHz.
-
Product
Adapter, 1.0 mm (f) to 1.85 mm (m), DC to 67 GHz
11921H
Coax Adapter
The Keysight 11921H precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
Product
Coaxial Adapter, 3.5 mm (f) to 3.5 mm (f), DC to 26.5 GHz
83059B
Contact Adapter (Receiver)
The Keysight 83059B instrument-grade 3.5-mm female to 3.5 mm female coaxial adapter offers outstanding performance to 26.5 GHz. With SWR typically better than 1.05, this adapter is ideal for most connector saver and interconnect needs.
-
Product
Passive Probe Interface Adapter
CX1151A
Digital I/O Adapter
The CX1151A is an adapter for passive probes for the voltage waveform measurements by the CX3300 series Device Current Waveform Analyzer.
-
Product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Test Fixture
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
Product
Dynamic Test Systems
H3TRB | HTGB (HTGS) | RTGB (RTGS)
Test System
Durability and reliability of wide-bandgap materials such as SiC and GaN are an important topic. The focus here is on new failure mechanisms whose effects are not visible with traditional H(3)TRB/HTGS – but which nevertheless have an influence on the real application.
