Test Adapters
See Also: Interface Test Adapters
-
Product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-01
Transceiver Adapter Module
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, To NI PXI-2529
510150148
PCB Adapter
This PCB Adapter was designed specifically for the NI PXI-2529, which uses 160 signals at 2 amps. This PCB Adapter will accommodate one or two NI TB-2634 terminal blocks. If 192 signals or 3 amps are needed for a different application; use # 510 150 155 which has 6 32-pin ribbon cable connectors capable of up to 3 amps each.
-
Product
Power Cord, 240V, 10A, North American
763068-01
Power Adapter
Power Cord, 240V, 10A, North American
-
Product
PCB Adapter, Receiver, QuadraPaddle ,192 Position, NI PXI-2532
510150141
PCB Adapter
This solution works with NI Terminal Blocks: TB-2640, TB-2641, TB-2643 and TB-2644. Part does not include ribbon cables. Please see parts 510150142 and 510150143 for complete solutions with ribbon cables.
-
Product
Mixed Signal Battery Test System
Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male
510140158
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, 90 Series, 2 VHDCI Male.
-
Product
PCB Adapter, Receiver, TriPaddle, 96 Position, To PCB-Mounted 1x96 Male DIN 41612 Connector
510104139
PCB Adapter
The 96 Pin Signal receiver module is made from Ryton R-7, withstanding temperatures up to 220°C. Nomenclature is molded on the module.
-
Product
EBIRST 78-pin D-type To 68-pin Male SCSI Adapter
93-006-401
Test Adapter
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
6TL60 Rotary Test Handler
H79006010
Test Platform
6TL60 has been designed according to the 6TL philosophy, following the concepts of flexibility, modularity and scalability, and with the aim of improving production efficiency as well as increase production capacity and reduce costs.The 6TL60 is the best production solution to automate test processes to reduce the cycle time and the footprint used in the manufacturing plan
-
Product
Interconnect Adapter, C-Size, Double Slot, 4 Module Positions
510109118
VXI Adapter
Interconnect Adapters funnel wiring from modules to a VXI card. The adapter has removable side, top and bottom plates. Connector cover plates and cable clamps are ordered separately.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
Test System
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
Iridium Physical Layer Test Systems
PLTS
Test System
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, PXI 160 Pin DIN
510140311
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, PXI 160 Pin DIN
-
Product
Rack based antenna test system
R&S®ATS800R CATR
Test System
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique rack based CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
A-quad-B cable
E1735A-001
Adapter Cable
The A-quad-B cable is a 3-meter cable that connects your machine's A-quad-B encoder output to the E1735A USB axis module's A-quad-B input connector. The cable is supplied with a mating connector for the USB axis module on one end. The other end is un-terminated, allowing you to make the connections you need for use with your machine's encoder.
-
Product
NI-5792, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782511-01
RF Adapter Module
The NI‑5792 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5792 modules.
-
Product
Adapter Plate, Allows 10 Module ITA To Accept 25 Module Enclosure
410112424
Adapter Plate
The Adapter Plate allows the user to use standard 25 module enclosures with the 10 module ITA. See enclosures in the 25 Module section for more options.
-
Product
EMS Test System
TS9982
Test System
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
Product
PCB Adapter, ITA, SIM, VTAC, 16 Pos, 6 Slot, to (1) Cat6
510171105
PCB Adapter (ITA)
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single Cat 6 connector. Great for COTS cable configurations. Compatible with all VTAC/SIM ITA modules. Please note this part is too wide for use in multiple adjacent slots.
-
Product
Coaxial Adapter, 3.5 mm (m) to 3.5 mm (f), DC to 26.5 GHz
83059C
Contact Adapter (Receiver)
The Keysight 83059C instrument-grade 3.5-mm coaxial adapter offers outstanding performance to 26.5 GHz. With SWR typically better than 1.05, this adapter is ideal for most connector saver and interconnect needs.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-614A-002
510140253
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, f/ Pickering 40-614A-002.
-
Product
Bottom Electrode SMD Test Fixture
16198A
Test Fixture
Designed for impedance evaluations of bottom electrode SMDs and supports 201 (mm) and 402 (mm) sizes
-
Product
H(3)TRB & HTGB Test Systems
Test System
SET offers two H(3)TRB and HTGB product lines which differ in the number of test object channels and the range of technical possibilities. The innovative systems are scalable, modular and standardized.
-
Product
Communications Test System for Frontline Diagnostics
ATS3000P
Test System
The ATS3000P is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000P also includes the sophisticated IF and baseband I/Q DigitalSignal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easyto-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets are available for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
RSE Wireless EMC Spurious Emission
TS8996
Test System
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
Conformance Test System
TS-RRM
Test System
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
Product
Bottom Electrode SMD Test Fixture
16197A
Test Fixture
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
Product
Benchtop Automated Functional Test
midUTS
Functional Test
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
Product
Eagle Test Systems
ETS-200T
Test System
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
Product
Adapter, 1.0 mm (m) to 2.4 mm (m), DC to 50 GHz
11922A
Coax Adapter
The Keysight 11922A precision 2.4 millimeter coax in adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and a frequency range from dc to 50 GHz.
