System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
Modulation Distortion Up To 70 GHz
S930707B
-
S930707B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 70 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930707B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Accelerated Life Test Systems
-
Test systems for accelerated life testing and product burn-in utilize Intepro’s electronic loads that are ideal where high power bulk loading is required. Characterization applications within Telecommunication and Aerospace sectors benefit from Intepro’s environmental stress screening (ESS)/Burn-in solutions
-
Product
SoftTest Design Testing Services
-
We are a one-stop turn-key solution provider for the design, development, integration and support for Automated Test Systems. Our capabilities include Functional parametric and non-parametric test systems, intelligent go/no-go gauges, vision systems and a variety of fixtures and adaters to interface with the product under test the most efficient way possible. SofTest Designs can adapt the development architecture to meet the preferences or requirements of our customers in terms of instruments, interfaces and software. With our own in-house machine shop, our development and integration times are greatly reduced optimizing resources and transfering the benefits to our customer's applications.
-
-
Product
370MHz To 6GHz Radiation Measurement System
RMS-0460
-
The MegiQ Radiation Measurement System (RMS) is a compact test system that performs 3-axis radiation pattern measurement in non-anechoic spaces.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 1.02k Ohm - SPST
40-294-121
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Broadband Coaxial Noise Sources
-
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
Product
PXI Resistor Module 4-Channel 1R to 510R with SPDT
40-293-114
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Automated Engine Testing System
-
Automated engine test system is intended for comprehensive testing of electrical motors with shaft rotation frequency up to 70 000 rpm. Such engines include:*high-voltage motors;*traction engines;*internal combustion engines;*AC motors;*DC motors;*synchronous engines;*asynchronous engines;*asynchronous engines with short-circuit rotor.
-
Product
Power Management Infrastructure
-
Universal functional test system for control assemblies for railway vehicles. Testing takes place in a high mix / medium volume environment. Several systems are in production throughout Europe and Asia. The systems are equipped with a Virginia Panel G12 adapter interface.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 2.5Ω To 472Ω
50-298-020
Programmable Resistor Module
The 50-298-020 is a high density programmable resistor card with 9 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 395kΩ
50-297-042
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Adjustable High Frequency Reference Ballast
HCS-109A
-
HCS-109A Adjustable High Frequency Reference Ballast also called High Frequency Current Source. Comparing to IEC Test Method, HCS-109A is an Equivalent Test Method which is economic solution. HCS-109A equipped with Spectrophotometer & Integrating Sphere Test System. It can also measure the photo, color and electricity parameters for high frequency fluorescent lamp.Specifications: • Input voltage: 200V~240V, 50/60Hz • Input Power: 80 W max • Output Current: 130mA~400mA (Adjustable), accuracy: +/- 1% • Output Frequency: 25kHz< +/-2.0% (Adjustable), accuracy: +/- 0.3kHz • Output current total harmonic wave distortion: THD<2.5% (HF current wave)
-
Product
HV AC Voltage Test Systems
-
Fivestar HV Testing Equipment Co., Ltd.
FSHV offers three different types of AC voltage test systems, the conventional type is AC test transformer design, mainly for testing objects of medium & low capacitance products, particularly for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (like inductive voltage transformers). Another is AC resonant test systems, according to series resonance circuit XL=XC (2πfL=1/2πfC), by setting F frequency of power supply or L inductance of reactor, generate a pure sinusoidal waveform of the test voltage, and the required input power is only 1/Q. Variable frequency type operates in a frequency range from 20Hz to 300Hz, ideal for field commissioning test of power cables and GIS/GIL. Variable inductance type outputs continuous AC voltage of power frequency (50/60Hz), mainly for factory testing of high and ultra-high voltage cables, power transformers, GIS, etc.
-
Product
Day Camera Testing
-
CI Systems' CCD test stations are used to carry out all the necessary tests to verify and compare the quality of a CCD based camera. These stations are based on CI Systems' reflective collimators, Visible Radiation Sources, special targets and integrated software, to project standard patterns with known geometry and intensity to the Unit Under Test. As a result, these stations are turnkey solutions for the CCD camera testing needs.
-
Product
Validation System
FLEX BMS
System
The FLEX BMS™ Validation System is a quick-connecting, highly flexible test system for rapid evaluation of centralized, single-board and distributed battery management systems. Utilizing Bloomy’s industry-leading battery cell simulators, COTS instrumentation, industry-standard connectors, and models that run in real-time, the FLEX BMS™ Validation System can easily be reconfigured to test a wide variety of BMSs. The FLEX BMS™ Validation System is used by national and regional safety and standards labs for certifying the BMS for a wide array of e-mobility products and applications.
-
Product
Software Capabilities
-
In test system development, the best hardware is only usable if its software control environment is robust and easy to use. If you are a test system developer, you need to look at both the hardware and software aspects of your vendors of choice.
-
Product
Additional hardware for our test systems
-
REINHARDT System- und Messelectronic GmbH
Our test systems are made up of modules which can be added to the needs of our customers.
-
Product
Carrier Acceptance Test Solutions for Network Operators
-
The Rohde & Schwarz carrier acceptance test systems provide access to the most important test plans of the world’s major mobile operators.Voice over NR, data throughput, protocol, positioning, RF, RRM and application testing – all relevant test scenarios are available on a common hardware platform.The entire range of 5G NR testing modes are available, covering sub-8 GHz (FR1) and mmWave (FR2) frequencies, and both non-standalone (NSA) and standalone (SA) modes.Contact your Rohde & Schwarz sales representative to learn more about the latest products and features.
-
Product
FPGA PXI High-Performance Digital I/O Card
GX3700
Digital I/O
The GX3700 is a user configurable, FPGA-based, 3U PXI card which offers 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features 47,500 logic elements and 2.1 kb of memory. The GX3700 is supplied with an integral expansion board providing access to the FPGA’s 160 I/Os. Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera’s free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
Product
Multi Channel Vibration Motor Aging Tester
BK2022
-
The BK2022 is the ultimate in aging testing for coin type vibration motors. You can connect up to 128 motors and the system will automatically test them all at the same time. It tests RPM, current, individual errors, and even total error and puts the information on the monitor in real time. You can store the results and retrieve them later to be analyzed so you can keep track of the accuracy and stability of your manufacturing process. In addition, BaKo’s BS1123-BS2022 program will be modified to fit your needs so that the testing you do is a custom fit.
-
Product
High Performance EV Battery Test System
-
Shenzhen Sinexcel RE Equipment CO., Ltd
The 6V series battery test system uses a full-bridge circuit topology with a higher digit sampling chip. It can provide higher precision and more dynamic test data, and can provide a complete test program for mainstream lithium-ion batteries and batteries with a variety of material systems such as sodium batteries.
-
Product
SWB-2834, 8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-34
Relay Matrix Module
8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2834 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PCI Precision Resistor Card 18-Channel, 1Ω To 122Ω
50-297-012
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
2 Pole 12 X 4 Low Thermal Relay Matrix Module
DP-cPCI-4113
-
A matrix is the most versatile switch topology. It is made up of rows and columns that connect any input to any output. With matrix switching system, it is easy to connect a number of instruments or sources to various test points of the UUT. The benefit of matrix switching is simplified wiring with which the overall test system can easily and dramatically change the internal connection paths without any manual intervention.DP-cPCI-4113 offers switching matrix in a single slot 6U sized cPCI module with flexibility to configure for 48 cross-points or 72 cross-points on factory selectable basis.
-
Product
SWB-2815, 4x86, 0.3 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-15
Reed Relay
4x86, 0.3 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Flexible Test Environments and Integration Services for your Integrated System Tests
TESTERLYZER® Frame 4.0
-
The TESTERLYZER® Frame 4.0 provides a flexible test environment for vehicle control units in an integrated system and is easily accessible from all sides. Customized adaption is provided for panel designs, control unit holders and cable adapters. A TESTERLYZER® I-Box 4.0 is a standard component of the TESTERLYZER® Frame 4.0 and provides the basis for a wide range of structures for the testing of control units, software and services relating to vehicles in research and development. The backbone of the I-Box provides all signals required with distribution to standardized adapter sockets and interfaces. The modular assembly structure ensures swift and safe setting up of the required test environment.
-
Product
Diagnostic Test Tools For Switching Systems
-
You know that verification and diagnosis of complex switching operation in a test system has always been an issue. Two of our latest offerings in diagnostic test tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
Product
ATE For Data Communications Equipment
-
• Developed for DRS Codem Systems, Inc. to test the CTM-IP product line of the Multi-Interface Protocol Converter.• Manufacturing Test support for the CTM-IP chassis and Interface Modules. Functional test of signaling, protocol and software configurations for various communication interface configurations.• Regression Test support for Engineering Product Development. Configurable test sequencing allows engineer to select specific tests for execution, with the ability to exercise all combinations of data rates and interface configurations.
