Wafer Inspection
Inspection of integrated circuits in wafer form for contaminants, flatness, size, and roughness.
See Also: Wafer, Wafer Thickness, Wafer Failure Analysis, Wafer Edge, Wafer Resistivity, Wafer Mapping, Wafer Probes, Wafer Probers, Wafer Handlers
-
Product
Inspection Microscope
Z-NIR
-
The McBain Z-NIR Near Infrared Inspection System is best-in-class for wafer-to-wafer and die-to-die alignment measurement and verification. This unique tool has been sold into many industries with various applications including sub-surface wafer and die inspection for cracks and bond integrity, MEMS, wafer bonding, 3-D chip stacking, failure analysis, process development, tool verification, part characterization, environmental testing and more.
-
Product
Fiber Inspection and Cleaning
-
Dust - just because you can't see it doesn't mean it's not there. A 1-micrometer dust particle on a single-mode core can block up to 1% of the light (a 0.05dB loss). The only way to know it's clean is to inspect it before you connect it. And if it's dirty, it needs to be cleaned with the right tools or you might just make it worse. Know it's clean with our cleaning and inspection tools.
-
Product
Manual & Automatic Inspection systems
-
Manual and Automatic inspection systems mounted on vehicles such as motortruck, van, railway testing wagons etc. Operation is either on the move or during a stop. Ideal for inspecting transmission and distribution lines and for electric transportation.
-
Product
Inline Wafer Testing
IL-800
-
Pre-process elimination of low-quality wafers using measured lifetime, trapping, and resistivity. Process control and optimization at dopant diffusion and nitride deposition steps.
-
Product
Inspection Class ROV
Phantom® L Series
-
THE PHANTOM® L6 IS THE NEWEST IN THE NEXT GENERATION OF PROVEN, RELIABLE UNDERWATER ROBOTICS PIONEERED BY DEEP OCEAN ENGINEERING IN ITS MANUFACTURE OF REMOTELY OPERATED VEHICLES (ROV), BUILT IN THE USA FOR NEARLY FOUR DECADES.
-
Product
Automated LED Inspection and Testing
-
Landrex Technologies Co., Ltd.
Automated LED Inspection and Testing
-
Product
Solder Paste Inspection Machine
3D SPI
-
The 6500 series is the measurement equipment provided by Jiezhi Technology for the small pads of solder paste printed on the PCB board. It will cause defects such as sharpness, offset, more tin, and less tin printing during solder paste printing. Causes defects in the later stage of production, this equipment can find problems in advance
-
Product
Solder Paste Inspection
3D SPI
-
Checking all the relevant points in the production process is essential, especially in terms of analyzing the causes of defects, fixing them, and – most importantly – preventing them in the future. That’s why solder paste printing is of fundamental importance for manufacturing complex assemblies: If paste printing isn’t performed correctly, the defect can impact the subsequent assembly and the soldering process, resulting in a tilted component or a poor or missing solder joint.
-
Product
Bond Tester for Wafers 2 - 12 inch
Sigma W12
-
Bondtester for wafers or at wafer level 2” – 12” (up to 300 mm)Precise testing and Cold Bump Pull (CBP) testingLarge X/Y stages X: 600mm, Y: 370 mmForce range from 1gf – 10 kgfBump pitch down to 20 µm
-
Product
Wafer and Cells PL System
HS-PL
-
Photoluminescence (PL) Imaging is a unique non-invasive inspection tool as it can be used in-line at many different steps of the cell manufacturing process. This facilitates the direct comparison of data obtained at one process step to data obtained at another. Additionally, PL imaging can be compared to electroluminescence (EL) imaging on finished cells using comparable equipment.
-
Product
Ceramics and Glass Inspection Systems
-
Due to their special material properties, ceramic and glass components are the basis of many high-tech products. The same properties make the production complex and costly. Substrate defects that lead to failure of finished components should be avoided at all costs. For this reason, early automated optical inspection is essential.For the inspection of sapphire and quartz glass Intego has developed systems to detect both external and internal defects and can also provide cutting suggestions. Using index matching it is possible to test rough or uneven glass profiles.For the inspection of ceramic components Intego offers solutions specifically tailored to the respective testing task. Our modular design uses standard components that have already been developed and tested and in most cases only requires minimal adaptation.
-
Product
Deep Inspection Kit
GRL-KIT-DI20
-
The GRL Deep Inspection Kit (KIT-DI20) addresses the gap between expensive, challenging-to-use VNAs and simple functional/continuity tests that are not adequate for high speed interfaces. Now, users without years of signal integrity testing expertise can perform professional measurements with high accuracy to 20GHz with easy-to-use equipment.
-
Product
Vision Inspection Systems
-
We have available with us diverse array of Vision System. These systems are based on high-end technologies and meet the requirements of diverse sectors. Further, our systems are an epitome of quality and available at economical prices. Details of different systems.
-
Product
X-ray Inspection System
TruView Prime
-
The TruView Prime is a fully motorized radiography system developed to meet the stringent requirements of electronics assembly and component inspection. The TruView Prime is professionaly built - something hard to find in entry level systems in the TruView Prime's price range.
-
Product
Universal Paint Inspection Gauge
-
The byko-cut universal is a multi-purpose paint testing instrument that measures paint coating thickness, paint adhesion, and coating hardness.
-
Product
Video Inspection Scope
BK3000
-
• Integrated 8.5 mm high-res imager allows for ease of use and ensures the product is always ready to go. Imager is resistant to dust, dirt, and water ingress for 30 minutes at depths of up to 3 meters.
-
Product
RFID Label Inspection System
Eurotech RFID FS
-
The Eurotech RFID FS RFID accurately rewinds rolls of RFID labels and validates their receptivity by running them through the Voyantic Tagsurance RFID inspection system. The unit allows stopping at a predetermined editing spot for the removal and replacement of the defective piece, as well as indicating defective labels by a mark printed by an inkjet system integrated with the machine. Adjustment of the closed loop tension control system can be made through adjusting the parameters on the software that control the servo motor control system. This gives the customer a virtual infinite range with which to wind their labels without cracking the inlay or antenna. As well accurate web adjustment and guidance is provided with a web guide system complete with an ultrasonic sensor. The Eurotech RFID FS RFID label inspection system is equipped with the Voyantic Tagsurance for testing the performance of RFID tags. This is done by verifying that the tag responds to commands on its whole operational frequency range, which means testing the tag on multiple frequencies, also outside the RFID reader frequency. Accurate power output combined with the Voyantic Snoop Pro antenna, optimized for testing tags inline at high speed, allows defining precise acceptance criteria and achieving stable quality.
-
Product
Inspection Scope
KI-TK1010
-
Inspection scope & cleaning materials for SC, FC, ST connectors, universal 2.5 mm & 1.25 mm ferrules (LC / 1.25 mm option)
-
Product
Vacuum Inspection
INDEC
-
INDEC vacuum test systems monitor a wide range of containers during the production process, including bottles, jars and cans, by measuring the cap panel concavity of their closures which is dependent on the vacuum inside. This non-contact inspection reliably identifies defective containers for automatic rejection.
-
Product
Fiber Optic Inspection Microscope
80760
-
The Miller 200x Microscope helps inspect fiber optic connectors quickly and easily. Its ergonomic design and built-in features make it ideal for field and lab use. The microscope features a pressure-activated on/off switch, focusing wheel, eyepiece, auxiliary white LED light source rated for 100,000 hours, adapter tip for inserting ferrule and battery compartment.
-
Product
X-Ray Inspection System
MX1
-
Manncorp’s new MX1 is a high-performance x-ray inspection system designed for real time imaging of multilayer PCBs and dense metal BGAs, μBGAs, and chip scale packages. Its high voltage (80kV), computer-controlled x-ray tube and 35 μm focal spot provide the power necessary for detection of a variety of defects including bridging, voids, and missing balls. The MX1’s standard camera features continuous zoom magnification from 4X to 50X and variable angle viewing up to 45°, and an upgrade to the x-ray tube can boost magnification to 225X.
-
Product
X-ray Inspection Of PCB Boards And More
The RTX Series
-
Glenbrook’s RTX Series of modular, real-time systems include models designed to meet a variety of production requirements including circuit board components. Numerous options make it easy to customize any RTX model to your specific application. All hardware and software elements are fully compatible to ensure the continued value of your equipment.
-
Product
Inspection Toolkit
OTK-4000
-
The Inspection Toolkit contains selected tools for verifying the existence of threatening electronic surveillance devices.
-
Product
High Resolution Wafer Thickness & Thickness Variation Gauge
MX 10x series
-
The MX10x series measure thickness and thickness variation on silicon wafers. It has a resolution of 10 nanometers and can be adapted to different thickness ranges within a few seconds.
-
Product
Wafer Test Solutions
-
Wafer Test Solutions has established leadership positions in developing and deploying application-specific test solutions for MEMS devices, offering wafer and frame probing stations suitable for R&D, Wafer Sort, and Final Test. We offer state-of-the-art solutions to test environmental and motion sensors in wafer and other advanced packages.
-
Product
Explosion Proof UV Inspection Light
-
he Labino MB Hercules Ex is an extremely durable product specifically developed for use in areas where the risk of an explosion is high. Offshore Oil Rigs, Refineries, Aerospace, and Defense often require explosion proof products to ensure safety for their inspection teams. The Midbeam Hercules Ex has successfully completed extremely tough tests, including tests for thermal conditioning, Impact Tests, Drop Tests and IP tests that led to the ATEX certification (Certificate: ITS17ATEX402144X). This unique product is suitable for use in extreme weather conditions varying from 104° Fahrenheit (+ 40° Celsius) to minus 4° Fahrenheit (- 20° Celsius).
-
Product
Chip Inspection System
GEN3000T
-
GEN3000T is an inspection system that performs automatic inspection of individual semiconductor chips.This revolutionary chip surface inspection system was achieved by combining the chip handling technology cultivated by Toray with the inspection algorithm used in the "INSPECTRA®" wafer defect inspection system.
-
Product
Protective Inspection Kit for Hazardous Areas
-
The kit provides all the tools required for the on-site inspection of a coating, including surface profile, dewpoint, relative humidity, both wet and dry film thickness and also adhesive testing.Measurement parameters include:Surface inspectionSurface profileSurface contaminationClimatic conditionsCoating thicknessAdhesion
-
Product
Protective Coating Inspection Kit 3
-
Measurement parameters include:Surface profileSurface temperatureClimatic conditionsCoating thicknessAdhesion
-
Product
Low to Modest Volume Clean, Inspect & Test
KI-TK071A
-
1310/1550 nm & 850/1300 nm source & Autotest power meter + acceptance reporting software, inspection microscope, cleaning materials. Interchangeable MPO, MPO/APC, SC, LC connectors (EAR99 Restricted)
