-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
SparkFun Spectral Sensor Breakout
AS7263 NIR (Qwiic)
-
The SparkFun AS7263 Near Infrared (NIR) Spectral Sensor Breakout brings spectroscopy to the palm of your hand, making it easier than ever to measure and characterize how different materials absorb and reflect different wavelengths of light. The AS7263 Breakout is unique in its ability to communicate by both an I2C interface and serial interface using AT commands. Hookup is easy, thanks to the Qwiic connectors attached to the board --- simply plug one end of the Qwiic cable into the breakout and the other into one of the Qwiic shields, then stack the board on a development board. You’ll be ready to upload a sketch to start taking spectroscopy measurements in no time.
-
Product
Modulation Distortion Up To 8.5 GHz
S930700B
-
S930700B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 8.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930700B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Spectroscopic Ellipsometers
M-2000
-
The M-2000 line of spectroscopic ellipsometers is engineered to meet the diverse demands of thin film characterization. An advanced optical design, wide spectral range, and fast data acquisition make it an extremely powerful and versatile tool.
-
Product
ThermalAir Desktop Series Temperature Forcing System
ThermalAir TA-1000A Desktop System
-
The ThermalAir TA-1000 high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -25°C to +200°C.
-
Product
OTDR
-
Wuhan Sunma Technology Co., Ltd.
OTDR, short for optical time-domain reflectometer, is an optoelectronic instrument used to characterize an optical fiber. It can offer you an overview of the whole system you test and can be used for estimating the fiber length and overall attenuation, including splice and mated-connector losses. It can also be used to locate faults, such as breaks, and to measure optical return loss.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784777-01
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
LXI Microwave Matrix, 10GHz, Dual 4x4
60-750-244
Matrix Switch Module
The 60-750-244 is a dual 4x4 10GHz microwave matrix. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 18GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
Product
M2 & BPP Systems
-
The M2 factor wil define the beam propagation characteristics compared to ideal Gaussian beam propagation. According to ISO Standard 11146 rightfully offers the laser beam characterization as "M2 times diffraction limited beam", as such, a perfect beam will have an M2 of 1. 1 will be the best achievable value and no beam could have an M2 less than 1. Our conceptual design is based on sub-assemblies allowing to change the sensing head in the M2 device, offering multiple wavelengths heads up to 2.7 microns from deep UV (knife-edge technology) and camera based technology with built-in automatic filter wheel for adjustment. For focused beams, the same measuring head could be attached to a device for meauring highly divergent or highly convergent beams - FocusGage-BA, wherein the Laser Analyzing Electronic Autocollimator offers the capability of divergence measurement with Coming Soon M2 definition. M2Beam is the cornerstone of those measuring devices.
-
Product
Antenna Characterization
-
Radiometrics Midwest Corporation
Radiometrics Open Area Test Site and 10 Meter Anechoic chamber provide ideal test sites for antenna characterization.
-
Product
Soft Front Panel for NI RF Analyzers
NI RFSA Soft Front Panel
Analyzer
The NI RFSA Soft Front Panel helps you quickly view and analyze RF signals using PXI hardware from National Instruments. The soft front panel features built-in measurements such as third-order intercept (TOI), complementary cumulative distribution function (CCDF), adjacent channel power ratio (ACPR), occupied bandwidth (OBW), channel power, and transmit power. With these one-button measurements, you can quickly measure, display, and store results, which makes NI PXI instruments ideal for characterization and validation environments. You can also use the NI RFSG Soft Front Panel for generating continuous waveform (CW) or modulated RF signals.
-
Product
Life Science Lab Instruments
-
Shimadzu's Life Science Lab Instruments are focused on developing new tools to help accelerate life science research by integrating novel chemistry with innovative technology to achieve a unique position as a true provider of solutions for life scientists. Shimadzu brings together technologies and tools that help you find out more about your biological sample. Whether it is a gel based experiment for understanding protein expression, characterizing differences in metabolism in patient studies, imaging tissue with mass spectrometry, Shimadzu can help you discover more about the biology of disease.
-
Product
Squeak & Rattle Sub-System And Component Testing
-
At MB Dynamics, we’re proud to provide clients in a wide range of industries with quiet, custom turnkey component testing systems for combined squeak & rattle testing as well as durability testing of different components and subsystems (in 1 to 6 DOF). Test items can be excited in one or more axes to understand and characterize the physics and root causes of BSRs. Real-world, on-road vibration conditions are multi-axis simultaneous – vertical, fore-aft or longitudinal, lateral, roll, pitch, and yaw – 6 degrees of freedom or 6 DOF. Affordability drives decisions to find BSRs by exciting in one or two – fewer than 6 DOF. That has been a driving force for MB – be effective at finding BSRs with a lesser number of shakers (DOFs) and thus reduce the test equipment cost of finding BSRs. Vertical-only can be effective; sequential vertical then fore-aft then lateral is one step closer to real-world; creating vibration in four or five axes of response simultaneously is even closer; and full 6 DOF systems that are quiet come closest to duplicating in the lab the on-road conditions. MB offers all these possibilities to meet trade-offs of budget, test time, road replication, and BSR detection effectiveness.
-
Product
Blackbodies
-
Blackbodies are devices that work as near perfect emitters of thermal radiation in range from visible to microwaves. There are many blackbodies available on international market. Inframet specializes in high-tech expensive blackbodies optimized for narrow market of high requirements. All blackbodies offered by Inframet are characterized by special features.
-
Product
Thermal Warpage and Strain Measurement Tool
PS200S
-
The TherMoir PS200S is a metrology solution that utilizes the shadow moir measurement technique combined with automated phase-stepping to characterize out-of-plane displacement forsamples up to 150 mm x 200 mm. With time-temperature profiling capability, the TherMoir PS200S captures a complete history of a sample's behavior during a user-defined thermal excursion.
-
Product
Solutions for Nondestructive Characterization of Elastic
Sonelastic
-
Sonelastic® is a line of solutions for nondestructive characterization of elastic modulus and damping of materials by the natural frequencies obtained by impulse excitation technique.
-
Product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784776-02
Signal Module
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
Product
Rebuilt Testers
-
Lorlin® manufacturers New and Rebuilt Discrete Component Semiconductor Test Systems for Transistors, Diodes, Zeners, Fets, IGBTs, SCRs, Triacs, Optos, Small Signal and Power Semiconductors. We measure, screen, test, analyze, characterize and sort the critical parameters of semiconductors devices including Leakage Current, Breakdown Voltage, Gain, Saturation Voltages, and offer a comprehensive test parameter library with an easy to use Windows based applications software. The systems us a Windows 10® 64-BIT Operating System with a USB 2.0 Interface. Engineering excellence, innovation, creativity and cutting edge technology has made Lorlin equipment well known for testing discrete components.
-
Product
Dimensional Metrology
Stand-Alone Metrology Family
-
Nova’s stand-alone metrology platforms are utilized to characterize critical dimensions such as width, shape and profile with high precision and accuracy and are used in multiple areas of the fab such as photolithography, etch, CMP and deposition in the most advanced technology nodes, across all semiconductor leading customers.
-
Product
PNA Network Analyzer Family
-
Choose between three PNA Series to get the right mix of speed, performance and price In R&D, obtain a higher level of measurement integrity that helps you transform deeper understanding into better designs On the production line, attain the throughput and repeatability you need to transform great designs into competitive products Get the ultimate expression of Keysight expertise in linear and nonlinear device characterization
-
Product
On-Wafer Measurements
-
Accurate DC/CV (and RF) statistical modeling of semiconductor devices requires collecting a significant amount of measured data from different wafers across several temperatures. Keysight Technologies recommends IC-CAP WaferPro as a turn-key DC/CV and RF automated characterization solution to help modeling and device engineers achieve more efficient on-wafer measurements across temperature. This new breakthrough solution is based on IC-CAP modeling software and efficiently controls DC/CV analyzers, network analyzers, probers, switching matrixes, and temperature chucks, as well as the powerful 407x and 408x Series of Keysight parametric testers.
-
Product
Nanoindenters
-
The KLA Instruments nanoindenter portfolio provides precise, reliable and repeatable testing to characterize static and dynamic mechanical properties of materials, under a wide range of test conditions.
-
Product
The Leading Measurement System for the Analysis of Porous Materials
ELWIS
-
ELWIS (Evaluation of Light Weight Impedance System) offers a full and rapid characterization of porous materials based on the analysis of a single sample. The ELWIS system consists of the ELWIS-A and ELWIS-S components which can be used independently from each other although both applications are needed for a complete material simulation.ELWIS-A measures acoustic parameters that are needed to evaluate the acoustic performance of sound insulation and sound-absorbing multi-layer materials. An additional impedance tube for absorption measurements at higher frequencies is available for ELWIS-A.ELWIS-S measures structural parameters that are needed to simulate the dynamic and acoustic behavior of sound packages in the medium to low frequency range (including the "Poisson Ratio" for foam materials).ELWIS is very easy to operate: Thanks to its user-friendly software, the system can also be used to obtain reliable results by users with only limited experience in the characterization of porous materials.
-
Product
LXI Microwave Matrix, 20GHz, Single 3x3, Terminated With Loop-Thru
60-751-133-C
Matrix Switch Module
The 60-751-133-C is a single 3x3 20GHz microwave matrix with internal termination and loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 20GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-01
Signal Module
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
Material Characterization Services
-
Accolade Engineering Solutions
As the direction of materials science continues towards studying the basis of properties on smaller and smaller scales, different techniques are used to quantify material characteristics and tendencies. Measuring mechanical properties of materials on smaller scales, like thin films, cannot be done using conventional hardness testing.
-
Product
Base Station Emulator
SUTP 5018
-
Designed to create a custom cellular environment to serve testing and characterization needs. The combination of high power, real-time computing and the software defined radio platform enables this instrument to create your own cells for testing in a compact size and cost-efficient way.
-
Product
CD Measurement and Advanced Film Analysis
FilmTek CD
-
Scientific Computing International
SCI’s leading-edge solution for fully-automated, high-throughput CD measurement and advanced film analysis for the 1x nm design node and beyond. Delivers real-time multi-layer stack characterization and CD measurement simultaneously, for both known and completely unknown structures. Patented multimodal measurement technology meets the challenging demands associated with the most complex semiconductor design features in development and production.
-
Product
ATI Performance Oscilloscopes
DPO70000SX
-
DPO70000SX ATI Performance Oscilloscopes deliver the industry’s most accurate capture of high-speed signal behavior to verify, validate and characterize your next generation designs. Capture up to 70 GHz signals with the lowest noise and highest fidelity, ensuring the most accurate measurements of your signal’s true characteristics.
-
Product
Automatic Fixture Removal
S95007B
-
Many devices do not have coaxial connectors and so they are put in fixtures in order to measure them in a coaxial environment. You must accurately remove the effects of the fixture to get a good measurement of the device under test (DUT). This option adds a powerful application wizard to guide you through characterizing a fixture and removing it from the measurement. The S95007B software is compatible with M980xA PXI Vector Network Analyzers.
