Compensators
-
Product
VHF True RMS Probe
-
The VHF True RMS Probe is a frequency compensated power probe capable of measuring power even in a multiple carrier installation. Regardless of physical waveform, the probe will measure the True RMS power of the signal. When used together with our Broadcast Power Monitor type 3024, you can add Web and SNMP capabilities to your mast site installation.
-
Product
Passive Probe, 10:1, 500 MHz, 1.2 M
N2843A
Oscilloscope Probe
The Keysight N2843A low-cost passive probe provides a 10:1 attenuation and features a high input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.
-
-
Product
8 Channels, RTD Measurement
RT1
-
The module provides 8 measurement channels, and can be programmed for interfacing to 2, 3, and 4-wire platinum RTD sensor configurations. The 4-wire mode (default) is the most accurate, providing excellent stability and repeatability. The RTD channels feature individual A/D converters and precision excitation/current drive. Programmable lead-wire compensation is provided for inherently less accurate 2 and 3-wire configurations. All RTD channels are self-aligning because each channel is automatically "aligned" on a rotating basis to eliminate offset and gain errors throughout the operating envelope. Programmability for expected resistance range and wire modes allows for optimization of scaling/resolution, as well as flexibility in reading many RTD types.
-
Product
Residential Combustion Analyzer w/ AC509 Carrying Case
C161C
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C161 Residential Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and now adds a heat exchanger test. Prints to optional printer. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
ReCalibration and Post Calibration Software
SI58
-
The SI58 software allows the user to set zero and span as well as do full temperature compensation and linearity corrections for your Validyne USB pressure transducer. The SI58 provides everything needed to change the range of your transducer and calibrate it through the new full scale pressure. Corrections to non-linearity and temperature error are also possible. The SI58 software provides prompts to the operator for temperature and pressure points to achieve an accurate calibration.
-
Product
High performance multisensor
Werth StentCheck®
-
High performance multisensor CMM with Integrated Werth Zoom® optic with magnification 0.7x – 6.8xRotary/Tilt Axis with high speed air bearing rotary axisRotary OnTheFly for fast measurementsContour image processing for fully automatic measurements of complex geometrical elements with sub-micron repeatabilityIntegrated goniometer (tilting axis) allows for the measurement of non-cylindrical geometriesUnique lighting design optimized for measurement of stentsTemperature compensation included
-
Product
Thermal Mass Flowmeters
-
ABB’s thermal mass flowmeters are suitable for all industrial and test rig applications that demand quick and precise gas measurement. The flowmeters directly indicate the mass flow or normalized volume flow of gases without any additional pressure and temperature compensation. They have an impressively high accuracy, short response time and a very wide flow range with virtually no loss of accuracy even at the lowest flow rates.
-
Product
Power Detectors
-
Macom Technology Solutions Holdings Inc.
MACOM’s power detectors are broadband devices that have integrated low loss directional couplers and built-in temperature compensation circuits. These detectors provide an easy way to monitor the power of a signal travelling in a specific direction along a transmission line. These detectors are conveniently housed in miniature lead free plastic surface mount package. Typical applications include; Power monitoring and leveling in Point-to-Point radios, IMS, Radar, VSAT, EW, Aerospace and Defense Systems.
-
Product
High Power DC Power Supply
-
*Low ripple and low noise*High resolution and accuracy (0.1mV/0.01mA)*Built-in high-accuracy 5 1/2 voltmeter and milliohmmeter*Supporting high-accuracy and dynamic programming output*High-luminance VFD screen with two lines& four channels display*Intellegent fan system fan will be automatically initiated according to the temperature*Supporting remote voltage compensation and multidata storage*Supporting external trigger input and output*Power-on-self-test, software calibration and standard rack mount*Using standard SCPI protocol*Communication mode: RS232/RS485/USB.
-
Product
Panel-mount Type Resistivity Meter (Four-Wire Transmission, 2-channel)
HE-960RW
-
HE-960RW connects resistivity sensor(ERF sereies) and measures resistivity and temperature in the sample water.This resistivity meter is ideal for such applications as the high-precision water monitoring employed at ultra-pure water plants used in semiconductor manufacturing.They utilize newly designed, high-precision, high-stability temperature measurement circuitry and a vastly improved temperature compensation function, an important element for measuring the resistivity of ultra-pure water.
-
Product
X-Band Silicon Radar Quad Core IC
AWS-0103
-
The AWS-0103 is a highly integrated silicon quad core IC intended for radar and 5G phased array applications. The device supports four radiating elements, single beam transmit, and dual beam receive and includes all requisite beam steering controls for 6 bit phase and gain control. The device provides 21 dB gain and +15 dBm output power during transmit mode and 7 dB gain and +7 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
Product
NI-9213, 16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module
785185-01
Temperature Input Module
16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module - The NI‑9213 is a high-density thermocouple input module that is designed for higher channel count systems. With this module, you can add thermocouples to mixed-signal test systems without taking up too many slots. The NI‑9213 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9213 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
Product
Linear regulated power supply with thyristor pre-regulation
NTN
-
High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units
-
Product
Button Load Cell
3000 Series
-
Button Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type provides a range of capacities up to 150 kN or 30 klb with better than ±0.5% (full scale) non-linearity. Three tapped holes are provided on the underside for ease of mounting. Fully welded cover, amplified and digitised versions are available on request.
-
Product
6GHz RF Signal Generator
TGR6000
-
0MHz to 6000MHz frequency range10Hz setability, ±1ppm frequency stabilityLocking to external frequency standard-110dBm to +7dBm amplitude, 0.1dB stepsFast stepping sweep with dwell times down to 10msList sweep of up to 1000 points of amplitude vs frequencyUser compensation tables for specific test set-upsStorage for 12 generator set-ups and 16 sweep listsCompact half-rack 2U casing uses minimum bench spaceFull remote control through RS232, USB, LAN and GPIBSignificantly lower cost than other 6GHz generators
-
Product
Linearizers
-
Gain Shape Linearizer Amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run, or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
Product
Accelerometers
-
The unit is based on micro machined MEMS technology. The unit contains a 35g sensing element. The element is scaled to optimise the resolution to suit the g range of interest. An internal amplifier provides an output between 0 and 5 volts. The on board microcontroller and temperature sensor are used for offset drift compensation. This unit can be re-calibrated at the factory.
-
Product
Passive Probe, 10:1, 300 MHz, 1.2 M
N2842A
Oscilloscope Probe
The Keysight N2842A low-cost passive probe provides a 10:1 attenuation and features a high input resistance of 10 MΩ. The probe can be adjusted for low-frequency compensation and high-frequency compensation.
-
Product
Pressure Sensor
2450
-
The Signet 2450 Pressure Sensor has a one-piece injection-molded PVDF body and ceramic diaphragm for superior compatibility in corrosive liquids. Three pressure range versions allow for optimal resolution matched to your sensing needs. Solid state circuitry eliminates drift (no internal potentiometers.) Built-in temperature compensation provides outstanding accuracy over wide temperature ranges.
-
Product
Fiber Optic Measurement Systems & Sensors
-
MTI Instruments offers large measurement range and standoff distance fiber-optic measurement sensors and probes that provide ultra sensitive linear output response. Our modular (interchangeable) non-contact fiber optic sensors systems have dual channel that enables the user to make simultaneous measurements. Our fiber optic probes are designed to automatically compensate large changes in reflectivity making it possible to monitor dynamic reflectance of up to 100:1 making it ideal for measuring vibration of ultrasonic horns, modal analysis of disk drive suspension, displacement and timing of fuel injectors and lateral motion measurements.
-
Product
GNSS Smart Antenna
iCON gps 70 series
-
For construction professionals, Leica Geosystems introduces the most efficient GNSS rovers, the Leica iCON gps 70 Series. With the iCON gps 70 T you can measure and stakeout points quicker than ever before without the need to keep the pole vertical and level the bubble. The combination of the latest GNSS technology and inertial measurement unit (IMU) equips the iCON gps 70 T with permanent tilt compensation and makes it resistant to any magnetic interference. Being fully calibration-free, the iCON gps 70 T is ready when you are – anytime, anywhere.
-
Product
Battery Chargers
-
Our dedicated range of battery chargers support Ni-Cd, Ni-MH, Li-ion and lead acid chemistries. Industrial lead acid battery chargers with temperature compensation are available at a variety of voltage levels and output powers. The high conversion efficiencies result in a small case style making the BC-SMPS product family ideal for system integration.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-J
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
PH And Temperature Pen
Ultrapen™ PT2
-
This instrument is designed to be extremely accurate, fast and simple to use in diverse water quality applications. Advanced features include automatic temperature compensation; highly stable microprocessor-based circuitry; user-intuitive design; and waterproof housing. A true one-handed instrument, the PT2 is easy to calibrate and easy to use. To take a measurement, you simply push a button then dip the pen in solution. Results display in seconds.
-
Product
SinglePhase Prismatic Capacitor
FMLI
-
Lifasa - International Capacitors, SA
These LIFASA capacitors are suitable for the individual compensation of inductive loads.
-
Product
Water Cut Meter
-
The Drexelbrook Universal IV Series products feature full compensation for both temperature and density as well as multiple mounting options which includes insertion and spool piece probes.
-
Product
Hydrometer
DMA-35
-
Explorer Technology Group (ETG)
Reads specific gravity and temperature. Package includes; a custom carry case, operating instructions and a 6 month limited warranty. The DMA-35n will be configured to read the specific gravity of battery acid at 77F/77F compensation and fluid temperature in degrees Fahrenheit as standard.
-
Product
Temperature Data Acquistion
THERMES-USB RF
-
Physitemp’s original Thermes high accuracy ISA based data acquisition system has been redesigned to create a more versatile USB model. The new system requires no internal connections to your computer and simply connects via an external USB port on your laptop or desktop computer. Two versions of the data acquisition system are available. The standard version, THERMES USB, is connected to your computer USB port. The wireless version - THERMES USB WFI, can be either directly connected to a USB port or, with the included wireless receiver, positioned up to 100 feet from the host computer. Each unit will accommodate up to 7 type T thermocouple sensors and multiple Thermes units may be connected to the same computer for more thermocouple inputs. A high accuracy electronic cold junction compensation circuit maintains typical system accuracy of ±0.2°C over an ambient temperature range of 15 to 35°C. Individual offsets may be added to each input in software to facilitate individual calibration of each channel. For information on our wide selection of Type T Thermocouple temperature probes.
-
Product
Two-way Wireless Thermocouple Temperature Data Logger with LCD
RFTCTemp2000A
-
The RFTCTemp2000A is two-way Wireless thermocouple based temperature data logger with LCD. Transmits up to 2000' maximum (outdoors unobstructed). Built-in memory also stores data internally. Features a built-in temperature sensor for cold junction compensation (CJC). An external thermocouple probe is required (not included). Accepts J, K, T, E, R, S, B, and N type thermocouples.
