Current
See Also: Direct Current, Alternating Current, Resistivity, Flow, Inductance
-
Product
Bench Power Supply, Adjustable, 2 Output, 0 V, 32 V, 0 A, 3 A
72-8690A
-
The 72-8690A from Tenma is a dual channel general DC power supply suitable for laboratory use. The dual channel (CH1 and CH2) can work in CV or CC mode and these two modes convert automatically according to the load. The CH1 and CH2 have auto tracking function. In this condition, the output of CH2 tracks the output of CH1. This function is usually used when adjustable symmetrical and double polarity power is required. Both CH1 and CH2 display the output voltage or current with a 6 digit LED meter. The main outputs can be connected in parallel or in series. This product comes with 2 years warranty.
-
Product
Elevated 1.68 (48.00) - 7.00 (198.00) High Performance Bias Ball Probe
POGO-1L24-7
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
8Thermocouple Robust Modbus RS-485 Remote I/O
ADAM-4118
-
8ch thermocouple(can be set to voltage or current)Operation temperature:-40~85°C,Power input:10VDC~48VDCNoise protection: 4kV surge(power),4kV EFT,8 kV ESD protectionInterface: RS-485/USB3000VDC isolation protectionLED indicator to monitor I/O status
-
Product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-1B-6-S
-
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Cable Testers
-
Can be used to fast check if Ethernet/telephone/BNC/HDMI cables are conducting, short-circuit, crossed or open-circuit. They are ideal tools for technicians to install, maintain and inspect week current system circuit.
-
Product
Standard 1.10 (31.00) - 2.50 (71.00) General Purpose Probe
HPA-1D
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 655Overall Length (mm): 16.64
-
Product
Power Supply, 150 V, 22 A, 3300 W
N8740A
-
Keysight's basic DC power supplies offer essential features for a tight budget. The Keysight N8740A is a 150 V, 22 A, 3300 W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
-
Product
Benchtop Multimeters (DMMs)
-
Transcat has benchtop multimeters that perform reliable electrical measurements during troubleshooting, repairs and installations. We sell thousands of precision DMMs annually, and our brands deliver multiple measurement functionality, including current, voltage, and resistance, within various ranges.
-
Product
Energy Analyser
DUCA-LCD
-
Energy Analyser for DIN-rail mounting (4 modules), for Single-Phase/Three-Phase systems with Graphic LCD screen, Co-generation Energy measurement and "Wide Range" Power Supply (24 - 240 Vac/dc); voltage and current waveforms and harmonics measurement and visualization; 2 digital output for pulses or alarms; 2 digital pulse input. Optional RS485 serial line interface (Modbus or ASCII_DUCBUS), Ethernet Interface (Webserver / Modbus-TCP).
-
Product
Alternate 2.58 (73.00) - 6.00 (170.00) High Performance Lead Free Probe
LFRE-25H-6
-
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Battery Fault Insertion Unit
-
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
Product
PXI 2A Multiplexer, 1-Bank, 8-Channel, 16-Pole
40-614C-019
-
This 1-bank, 8-channel, 16 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Shunt Voltage References
-
Analog Devices offers a broad line of shunt precision voltage references that combine excellent accuracy and temperature stability with low noise and small packages. These devices operate in a manner that is functionally equivalent to a Zener diode. The bias current must be set higher than the sum of the maximum quiescent current of the voltage reference and the maximum expected load current. Since shunt voltage references are typically biased with a resistor, the voltage reference can operate on a wide range of input voltages.
-
Product
Programmable DC Load Current Waveform Generator
9923
-
9923 application software can be used to edit arbitrary waveform, providing electronic load simulation different sink current conditions
-
Product
Broadband Current Probes
-
Conducted currents can be measured without making direct contact with the source conductor or metallic surface by means of clamp-on broadband current probes. The BCP-5xx EMC Current Probes are designed to permit field intensity meters, spectrum analyzers, and other 50W impedance instruments to measure quantitative magnitudes of current.
-
Product
20Hz Generator
-
Signals & Systems India Private Limited
In order to implement a 100 % stator earth fault protection based on subharmonic injection, a 20Hz voltage is injected into the generator star point. The 20-Hz generator SGEN-1001 is used in combination with the Band Pass Filter SBPF-1001 in the Stator Earth fault protection. The injection can be performed by connecting the SGEN-1001 and the SBPF-1001 to the load resistor of an earthing or neutral transformer. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. From the driving voltage and the fault current, the protective relay determines the fault resistance.
-
Product
Low Noise Amplifier
1010
-
A low noise, DC-coupled amplifier is packaged in a rugged, die-cast aluminum case with BNC connectors enabling input and output. Provides very low voltage noise and current noise in the critical region of 0.1 Hz to 10 Hz making this the ideal amplifier for thermopile detectors in sensitive systems design and laboratory experiments.
-
Product
PXI Very High Density Multiplexer, 24-Channel, 8-Pole
40-675A-002-24/8
-
The 40-675A-002-24/8 is a 24-channel, 8-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
Trip Amplifiers
-
Datexel manufacture a large range of Trip Amplifiers and Process Limit Alarms that accept universal inputs and provide either relays or NPN or PNP transistor outputs. The DAT5028 is also an isolated signal converter and has a local display with up to 4 relays and is DIP switch programmable. The inputs can be Thermocouples, RTD, mV, mA, Resistance, Potentiometers or Voltage. They can be supplied fully configured set up by PC or DIP switches. The DAT5024 is a trip Amplifier / Temperature limit alarm for RTD's, Thermocouples, Voltage, Resistance and Current with the option of 1 or 2 relay outputs hysteresis and delay timers. The DAT5024 E range is an economical choice with DIP Switch programmable for voltage or current input. Either 1 relay or 2 relays (SPDT) are available with delay timers.
-
Product
RF Reference Source
96040A Series
-
The 96040A RF Reference Source enables you to simplify your RF calibration system by replacing many of the instruments and accessories that make up your current system.
-
Product
Dual Mobile Comm DC Source w/ Battery Emulation, DVM
66319D
-
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.
-
Product
Joining Monitor
-
We are offering a variety of monitoring equipment for current, voltage, pressure and displacement which is indispensable for quality control of precision micro joining.
-
Product
Four Channel Relay Board for Power Supply Isolation
FXA-113 PSU Relay 4CH
-
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
-
Product
PXI 25 x SPST Reed Relay 2.5 Amp
40-136-111
-
Pickering Interfaces 40-136 Power Reed Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. The 40-136 is suitable for voltages to 200V and current to 2.5A. Available in Normally Open (SPST & DPST) configurations. Connections are made via a front panel mounted 50 or 78-pin D-Type connector.
-
Product
Programmable Current Preamplifier
99539
-
The Model 99539 is a modular, multi-channel current preamplifier with parallel, logic level, gain control input. It consists of circuit boards which plug into a 3 1/2" high by 19" wide rack chassis.
-
Product
Alternate 1.00 (28.00) - 2.00 (57.00) General Purpose Probe
P2663G-1C2S
-
Current Rating (Amps): 3Average DC Resistance lower than (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 90Full Travel (mm): 2.29Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 810Overall Length (mm): 20.57
-
Product
PWM Type AC Power Supply
LSP-5KVA
-
• Circuit Type: (IGBT) MPWM Pulse Duration Modulation • Input: 1 Phase 220V±10%, 50Hz/60Hz±5% • Output Voltage: HIGH/LOW Adjustable 1)1 Phase Voltage Range: (HIGH)0～300V, (LOW)0～150V 2) Nominal Voltage: +10%～+25%, -10%～-30% • Output Frequency: 50Hz, 60Hz, adjustable between 45 and 70 Hz, 400Hz • Load Voltage Stabilization Rate: ≦0.5% • Frequency Stabilization Rate: 0. 1% (Fix Point 50Hz, 60Hz and 400Hz) • Wave Distortion Rate: ≦2% (Resistor Load); Efficiency: ≧85% • Output Instruments: Frequency Indicator, 4-digits RMS digital frequency indicator, resolution is 0.1Hz Voltage Meter, 4-digits RMS digital voltage meter, resolution 0.1V Ampere Meter, 4-digist RMS digital ampere meter, resolution 1Ma Power Indicator, 4-digits RMS digital power indicator, resolution 1W Power Factor Meter Resolution 0.001 • Protective Devices: Over load, short circuit, over voltage, over current, over temperature protective and alarm devices • Operating Environment: Temperature 0～40℃ Relative Humidity 0～90%
-
Product
TTC-1 Tracking Test Chamber
TTC-1
-
It is according to IEC60695 and IEC60112 (GB4207), the Tracking Test Chamber TTC-1 is intended for determining the degree of protection against formation of conducting paths in solid insulating materials, due to the electric stress and electrolytic contamination of the surface. This method simulates tracking currents on insulation material by providing drops between electrodes. During the process of normal use, insulating material may be exposed to moisture and dirt, if conductive, may cause stress and fire hazard.
-
Product
DM 150-Watt Transmitter
Loc-150Tx
-
The Loc-150Tx, 150-Watt DM Transmitter is used primarily with the Defect Mapper (DM) Receiver, however it is also useful for those needing a low frequency, high output transmitter. Typically, the Loc-150Tx, transmitter (DM transmitter) is used to apply a signal current to the anode bed. The pipeline returns the signal via coating faults back to the transmitter. The Loc-150Tx transmitter is designed to be powered from CP (Cathodic Protection) stations, AC or external batteries, eliminating the need for internal batteries. This transmitter has a direct connection mode to apply the locate frequency onto the conductor. There is no clamp or induction mode.
-
Product
Wave Buoy
MOTUS
-
The MOTUS (movement in Latin) Wave Buoy is a perfect solution for collecting environmental data in coastal areas.Collect reliable environmental data with MOTUS Wave Data Buoy.The MOTUS (movement in Latin) Buoy is a perfect solution for collecting environmental data in coastal areas for all-year deployments. The platform used for collecting data is a robust buoy which has proven to be an excellent platform for providing high accuracy and reliable meteorological and oceanographic data. The wave buoy can effectively combine various Hydrological and Meteorological parameters. Basic parameters such as wind, waves, and currents can easily be expanded to include sensor packages with different water quality sensors. Data is controlled and synchronized by the data management systems that Xylem Analytics offers, which also controls and powers real-time communication. This provides a low-power efficient system offering long-term deployment capabilities.The MOTUS Wave Buoys combine our ultra-low power and field-proven solutions from developing oceanographic and water quality sensors. We have 60 years of experience operating in the industry, providing you with an optimal platform based on the buoy, a rugged, lightweight polyethylene buoy deployed in more than 40 countries all over the world. By selecting Xylem as your partner in your projects, you are on track for the lowest overall cost of ownership and a versatile platform that can be tailored to your needs. The MOTUS Buoy is developed for both scientific and commercial use.
