Product

PRO8 LD / TEC Drivers

-

Thorlabs, Inc.

Thorlabs, Inc.

This section includes single-channel laser current controllers, temperature controllers, and combined LD/TEC controllers compatible with our PRO800 and PRO8000 chassis.

Product

Analogue (1kV below) Insulation Tester

8052 IN

-

Standard Electric Works Co., Ltd

8052 IN - Standard Electric Works Co., Ltd

● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 3Ω & 500Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.

Product

Load Cell Amplifier Signal Conditioner with Removeable Terminals

MODEL LCA-RTC

-

Transducer Techniques, Inc

MODEL LCA-RTC - Transducer Techniques, Inc

The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.

Product

Test Equipment for Instrument Transformer

-

Soken Electric Co. Ltd

Soken Electric Co. Ltd

is desirable for measuring ratio errors and phase angles of low current (voltage) transformers used in electric devices, such as watt hour meters, smart meters, digital current meters, and transducers, etc.

Product

Pulser/Receiver

DPR500 Family

-

Imaginant Inc.

DPR500 Family - Imaginant Inc.

The DPR500 DUAL Pulser/Receiver is the first dual channel, modular instrument consisting of two complete pulser/receivers integrated into one unit. Receiver modules are currently available in the following bandwidths: 500 MHz, 300 MHz, and 50 MHz. The DPR500 may also be configured as a single channel instrument using any of the available modules

Product

Outdoor AGC Optical Node

SR814

-

Hangzhou Softel Optic Co., Ltd.

SR814 - Hangzhou Softel Optic Co., Ltd.

Based on plenty of experience about CATV HFC network optical fiber transmission equipment, we developed SR802, SR802B, SR804, SR804B series field optical receiver which is two-way optical receiver; They are mainly used in long-distance optical fiber transmission of TV image signal, digital TV signal, telephone voice signal and data (or compressed data) signal. We are innovating the product technology, rebuilding the line structure and Improving the process quality since we developed the first CATV optical receiver successfully in 1995; The current WR series optical receiver are not only of the lead position in domestic level regarding line technique, but also the same as imported product regarding technological quality; We have developed a variety of different models for users to choose models.

Product

Transducers

-

Rishabh Instruments Pvt. Ltd.,

Rishabh Instruments Pvt. Ltd.,

Current Transformers With Transducer for the measurement of AC current. A very reliable, efficient and robust current transformer for measurement of AC current. It provides 4 to 20 mA or 0 to 20mA DC output.

Product

Digital Thickness Gauges Ultrasonic Coating Thickness Meter

HC-220

-

Shenzhen Chuangxin Instruments Co., Ltd.

HC-220 - Shenzhen Chuangxin Instruments Co., Ltd.

HC series of coating thickness gauge is a portable thickness gauge with eddy current thickness method and electromagnetic thickness method. It can be used to quickly and accurately measure the thickness of coating or cladding material withoutdamaging it. As an  essential instrument for professional material protection, this coating thickness gauge is widely used in manufacturing industry, metal processing industry, chemical industry and commodities inspection etc. ,both in the laboratory and in the engineering field. It can measure the thickness ofnonmagnetic layer on magnetic metal substrate condition (such as steel, iron, alloy and hard magnetic steel, etc.) and the thickness of conductive layer on nonmagnetic metal substrate condition (such as rubber, paint, plastic, anodic oxidation film, etc.).

Product

Instrument Systems General Accessories

-

Konica Minolta Sensing Americas, Inc

Konica Minolta Sensing Americas, Inc

Instrument Systems General Accessories current range of optical probes and measurement adapters using fiber optics as a means to transport light in the spectrometer was a primary goal sought by Instrument Systems from the beginning of their product development.

Product

High Power Digital Lab Series Regulated DC Power Supply – 2KW

-

Aplab Limited

Aplab Limited

- 2000W different combination- High current density.- 19″ rack adaptable -3U high- Front panel potentiometer to set V&I- Remote sensing- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I

Product

Switching Regulators

-

Analog Devices Inc.

Analog Devices Inc.

Analog Devices offers a wide range of switching regulators that operate in step up (boost), step down (buck), and inverting modes. These devices are capable of generating a fixed or adjustable output voltage, and offer up to 2 A of output current. Some of the features available in ADI’s portfolio of switching regulators are low battery detector, user adjustable current limit, a variety of switching frequencies, and a reduced number of external components. This highly integrated, versatile family of products is intended to minimize external components for space challenged applications.

Product

40 kV AC Withstanding Voltage Tester

-

AllWin Instrument Science and Technology Co., Ltd.

AllWin Instrument Science and Technology Co., Ltd.

Leakage current at real-time detectionAlarm value can be preset freelyAudio alarm, High-voltage breakdown protection

Product

Broadband Current Probes

-

A.H. Systems, Inc.

A.H. Systems, Inc.

Conducted currents can be measured without making direct contact with the source conductor or metallic surface by means of clamp-on broadband current probes. The BCP-5xx EMC Current Probes are designed to permit field intensity meters, spectrum analyzers, and other 50W impedance instruments to measure quantitative magnitudes of current.

Product

VME64X 7U 10 slot with P0

101V64XM10-0621R

-

ELMA Electronic, Inc.

101V64XM10-0621R - ELMA Electronic, Inc.

7U VME64x Backplane 10-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.

Product

DC Alignment

SEP/SIP

-

Nihon Denji Sokki Co., Ltd

SEP/SIP - Nihon Denji Sokki Co., Ltd

There are analog phase control type DC power supply type and digital control type inverter energy saving type. We provide the most suitable equipment according to the current capacity and cycle time.If the "start command" is executed from the existing molding equipment, each mode of "alignment-pause-demagnetization" is continuously operated by the program inside the instrument. It is also possible to share an emergency stop signal and output an output current abnormality signal.

Product

Bench Digital Multimeter, Calibrated, Data, 1 kV, 10 A, 3.8 Digit

72-1015 CAL D

-

Tenma

72-1015 CAL D - Tenma

The 72-1015 CAL D from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.

Product

Split type Pulse Current Sensor

CTF-03

-

MULTI MEASURING INSTRUMENTS Co., Ltd.

CTF-03 - MULTI MEASURING INSTRUMENTS Co., Ltd.

Suitable for the operation and cable continuity check of the equipment by pulse current detection method. Wide AC current range from 0.1mA to 8A. Ultra compact and light weight. High sensitivity and least affection from external magnetic field.