System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
Environmental Control System Test Platform
Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
System Level Test and Burn-in Solutions
-
System Level Test (SLT) is a paradigm shift from traditional structural and functional testing. The device is tested in a complete, integrated system to evaluate its compliance against specified requirements. The system approach allows for higher and more cost-effective test coverage especially for multi-function and non-deterministic devices. It also brings new integration and test challenges like: ..Designing test fixtures on Burn-in Boards with system components ...
-
Product
Flight Control System Test Platform
Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
TURBO AIR SYSTEM TEST KIT WITH SMOKE ADAPTER
TPT69700A
-
*Helps locate air leaks in turbo system components by plugging the output side of the turbo and the intake inlet*Air is applied through one adapter to show the presence of leaks within the system*Six pairs of stepped adapters to fit most turbo systems on cars and light trucks
-
Product
HSI System Test Panel
TA-500
-
This panel was designed to test primarily the NSD360 series of HSI systems. Panel allows running the complete system on the bench. Included is a panel mounted TA-902 API which can also be used for testing external instruments via a panel mounted switch. The API and standard meter drives allow testing many different instruments.
-
Product
Bluetooth RF Test System
FRVS
Test System
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
Product
SoC Test Systems
Test System
SoC (System on Chip) devices integrate multiple different functions into a single chip. Our SoC test systems can test all the integrated circuits in SoC devices, including logic, analog, RF, DC and imagers by flexible configuration of the cards/modules used in the test system.
-
Product
Semiconductor Test System
TS-960e
Test System
The GENASYS Semi TS-960e PXI Express Semiconductor Test System is an integrated test platform that offers comparable system features and capabilities found in proprietary ATE systems. Available as a bench top system or with an integrated manipulator, the TS-960e takes full advantage of the PXI architecture to achieve a cost-effective and full-featured test solution for device, SoC and SiP test applications.
-
Product
Scalable Tester System for Functional Testing
UTP6010
Functional Test
The UTP6010 is a scalable tester system for functional testing, comprising an integrated main switching unit, a keyboard drawer and a swivelling monitor. It is the reliable, modular, low priced UTP starter kit. The system is suitable for tester applications, where space-saving devices are required, because its construction height is only 12 HU (excluding keyboard drawer and main switching unit).
-
Product
Compact & Flexible Test Systems for FCT,ICT, ISP and Boundary Scan Designed for Easy Integration
LEON Rack
Test System
The LEONRack test system is a flexible test system that could be installed in automation or handling solutions. It is highly flexible and available in three different chassis sizes from low pin count to high pin count test systems. As part of the LEON Family, LEONRack is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
Asynchronous System Level Test Platform
Titan
Test Platform
The Titan System Level Test (SLT) platform delivers maximum flexibility, scalability and density in semiconductor test environments that require the highest levels of system performance testing. Titan is Teradyne’s solution for high-volume mobile application processor SLT requirements.
-
Product
Communications System Analyzer
Freedom R8200
System
The Freedom R8200 from Astronics Test Systems represents a major step in the evolution of the Land Mobile Radio Test. The Freedom R8200 is the first and only test instrument that combines comprehensive digital and analog LMR testing with the ability to measure important RF network characteristics, such as Distance to Fault (DTF), Return Loss, and Voltage Standing Wave Ratio (VSWR). The Freedom R8200 is also the only service monitor with the abilityto display advanced RF Parameters in a Smith Chart for more complicated network analysis
-
Product
Mixed signal LSI test system
-
Multi-pin type model is now launched in WL27 Logic/Power mixed LSI test system.This system is suitable for multi-site test in A/D mixed device such as automotive・motor driver IC. It’s a high throughput and cost performance mixed signal LSI test system.
-
Product
Scienlab Battery Test System — Cell Level
SL1002A
Test System
Test System with up to 36 Channels.The Keysight SL1002A provides sink and source with 0 to 6 V, 100 to 600 A, 0.6 to 3.6 kW and 36 channels for battery cells.
-
Product
Functional Testing and Test Engineering
-
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
-
Product
Macro-Vickers Hardness Testing System
LV Series
-
LECO's LV Series Macro-Vickers Hardness Testing Systems offer an affordable testing system suitable for larger, heavier samples used in welding and other demanding applications. Models include analog and digital, with options to upgrade to automatic configurations.
-
Product
PXI Precision Resistor Module 6-Channel, 3 to 11.4M
40-297-053
Programmable Resistor Modules
A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 32.7k Ohm - SPST
40-294-132
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
SWB-2813, 4x21, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-13
Matrix Switch Module
4x21, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2813 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 2.5Ω to 472Ω
40-298-020
Programmable Resistor Modules
The 40-298-020 is a high density programmable resistor module with 9 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 2Ω to 31.5Ω
40-298-110
Programmable Resistor Modules
The 40-298-110 is a high density programmable resistor module with 9 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
RF Generators
-
RF signal generators are equipment’s used to generate high frequency signals at a particular frequency for testing systems in the lab. RF Signal Generators from the leading manufacturers are listed here. Find signal generators based on the required frequency range, power level, modulation and other parameters. View product specifications, download datasheets and get quotes on parts that meet your requirement.
-
Product
JTAG External Modules for Cluster Test
JEMIO
-
The JTAG External Modules JEMIO™ for Cluster test are intended to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system. For many designs, Boundary-Scan has adequate access to on-board signals, but signals that go off the board often cannot be tested by a JTAG tester. By adding JTAG access to these off-board signals, JEMIO™ modules can increase the board's JTAG test coverage, possibly reducing the need for implementing another test method or for developing alternative tests to reach the required level of test coverage.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
Test System
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
Multi-Purpose RF Test System
SPA1241
-
The S - Series multi-purpose RF test system can be used in many applications such as R&D lab, ATE factory testing, EMC testing, field testing, and general purpose RF design. The S - Series is a flexible alternative to expensive and bulky RF test equipment. As shown in the setup in the upper right the S-Series system can be utilized to simultaneously provide all RF functions using its 7 inch front panel display or can be connected to a larger monitor for ease of viewing multiple windows at the same time
-
Product
Motion Simulator For Test Systems
Metis
-
METIS is a motion simulator for sensor and end system level testing. Configurable design allows you to create system you need! - 1-axis rate table for gyro testing - 2-axis unit for 6DOF accelerometer and gyroscope testing - 3-axis Gimbal system for simultaneus Yaw, Pitch and Roll stimulus.
-
Product
Static Load Cells (5 N to 300 kN)
2530 Series
-
The Instron 2530 Series static load cells are precision force transducers engineered for versatile use in tension, compression, cyclic, and reverse stress testing, delivering accurate measurements down to 1/500th of their capacity. Individually temperature-compensated and calibrated, they support automatic recognition and electronic calibration, and are built to international force-measurement standards (ASTM E4, ISO 7500-1 class 0.5, and JIS B7721, B7733). With overload protection (150 % of rating without damage, 300 % without mechanical failure), the 2530 family offers consistent, repeatable performance across a wide force range (5 N to 300 kN).2530 Series load cells with capacities of 5 N to 100 N are for use with 3300, 3400, 5900, and 6800 Series testing systems.2530 Series Load cells with capacities of 500 N to 300 kN are for use with 3300 and 3400 Series testing systems.
-
Product
Comprehensive Simulation of Master, Slave and End Nodes in A 2 B ® Networks
Infotainment Test Device ITD 1024
-
The complexity, cost and weight of audio systems are significantly reduced with the Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. Regardless of their hierarchical structure or use as master or slave, all A 2 B ® products must be adequately tested before use. This applies, for example, to HiFi amplifiers/loudspeakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators or sensors.Our small and very compact infotainment test system ITD 1024 takes on this task for you: It comprehensively and extremely reliably tests all A 2 B ® signals and communication in all phases of the product development process - during development, for validation and in production.
-
Product
NI-9213, 16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module
785185-02
Temperature Input Module
16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module - The NI‑9213 is a high-density thermocouple input module that is designed for higher channel count systems. With this module, you can add thermocouples to mixed-signal test systems without taking up too many slots. The NI‑9213 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9213 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
Product
Stationary Circuit Breaker Testing
ACTAS L260
-
High-precision test system for function tests on various types of switchgear device, including circuit breakers, disconnectors or earthing switches, regardless of the type of drive unit.The inputs and outputs are connected flexibly via a terminal strip, making the test system particularly suitable for use in development and laboratory environments as well as in production environments.
