System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
Modulation Distortion Up To 50 GHz
S930705B
-
S930705B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 50 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
External Frontend
FE50DTR
-
The R&S®FE50DTR external frontend can extend the frequency range up to 50 GHz for Rohde&Schwarz signal and spectrum analyzers as well as signal generators. The R&S®FE50DTR enables signal up and downconversion directly at the device under test (DUT), lowering cable losses, increasing sensitivity and delivering more power at the antenna in an OTA environment. With a dual connector system, testing of active components is an easy task.
-
Product
AMIDA 3001XP Tester
-
AMIDA has introduced two new analog/mixed-signal and logic options in the AMIDA-3000 series in recent years—the AMIDA-3001XP and AMIDA-3KS test systems. Both reinforce the AMIDA-3000 series' ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. The AMIDA-3000 series provides more than twice the number of analog channels of its modules per test system, thus greatly reducing the acquisition cost of each channel and more than doubling the number of analog channels in the entire test system. This results in a higher number of parallel tests and a higher level of capability for this system, as well as a lower and more cost-effective IC unit test cost for this tester. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The built-in instant messaging protocol detection function of AMIDA-3001XP test machine not only simplifies the complexity and difficulty of test development, but also greatly shortens the test time by using its high-speed computing capability.
-
Product
Multi Channel Linear Vibration Motor Aging Tester
BK8018B
-
The BK8018B is our biggest Aging Tester for linear vibration motors. Connect up to 20 DUT's and the system will automatically test them all simultaneously. As well as evaluating current, it can also connect to accelerometers to test vibration characteristics. You can see information on the monitor in real time, and also store it to analyze later so you can keep track of the accuracy and stability of your manufacturing process. In addition, we will modify BaKo’s BS1123-BS8018 program to fit your needs so that the testing you do is a custom fit.
-
Product
Multiport Coaxial Switch, DC to 20 GHz, SP4T
87204B
-
The Keysight 87204B terminated multiport switch provides the life and reliability required for automated test and measurement, signal monitoring and routing applications. Innovative design and careful process control created the Keysight 87204B which meet the requirements for highly repeatable switching elements in test instruments and switching interfaces. The Keysight 87204B is designed to operate for more than 10 million cycles. The exceptional 0.03 dB insertion loss repeatability is warranted for 5 million cycles at 25° C. This reduces sources of random errors in the measurement path and improves measurement uncertainty. Switch life is a critical consideration in production test systems, satellite and antenna monitoring systems, and test instrumentation. The longevity of this switch increases system uptime, and lowers the cost of ownership by reducing calibration cycles and switch maintenance.
-
Product
Autoinjector Testing System
-
Instron’s Autoinjector Testing System is designed to perform full functionality testing on a wide variety of drug delivery devices, including safety syringes and both needle shield and button-activated formats. Developed in collaboration with pharmaceutical manufacturers and CDMOs, the system captures essential performance requirements such as activation force, injection time, dose accuracy, needle depth, and click detection. It supports compliance with international standards like ISO 11608 and can be configured for integration with collaborative robots to enhance automation and throughput.
-
Product
MCB Thermal Verification Test Bench
-
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
Product
Maxirack - 200 x 60 x 80 cm
OTP2 module no003
-
The rack serves as the basic framework for your individually designed test system. Various OTP² modules can be installed in the 200 x 60 x 80 cm rack in order to meet the most varied of test requirements.The modular architecture of the OTP (Open Test Platform) is based on a flexible instrumentation matrix, LXI-based sources and measuring devices, combined with a high-quality transfer interface for connecting the test adapters. The systems can easily be expanded with customer- and application-specific functions. We use standardization to build cost-effective systems that still fit your requirements exactly.
-
Product
PXI Precision Resistor Module 3-Channel, 3 to 1.51M
40-297-150
Programmable Resistor Module
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Quality Management Software
QMan
-
The Paperless Repair software QMAN is a powerful quality management system. It helps achieve higher quality assurance, reduce production costs and shorten repair time – regardless of which test system you are using.
-
Product
PCI Precision Resistor Card 18-Channel, 1Ω To 470Ω
50-297-014
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Power Supply Modules
-
Fixed power supply modules provide you with up to four separate voltage outputs isolated from the PXI backplane. Any combination of 3.3V, 5V, 12V or 15V can be specified with a maximum current capability of 4A for the 3.3V option; the software provides on/off control and status monitoring for each output. Dual programmable power supplies are capable of supplying up to 60 Watts of power. These are ideal solution for applications where a self contained test system with a high power supply power capability is required in a PXI format.
-
Product
Damped Oscillatory Magnetic Field Immunity Tester
DOMF61000-10
-
DOMF61000-10 damped oscillatory magnetic field immunity test system included damped oscillating wave generator and single ring coil, it’s designed for to do damping oscillation magnetic field immunity test and fully meet IEC 61000-4-10, EN61000-4-10 and GB/T 17626.10 standards requirement.
-
Product
Electro Mechanical Solenoid Switch
-
Electro Mechanical Solenoid Switches are a type of switch that are used in applications that require remote-controlled or timed transmission line switching. These switches are very useful in operational systems and test setups where they supply a variety of switching combinations.View more Electro Mechanical Solenoid Switch
-
Product
Life Cycle Module Testing System
LCN
-
Full featured test system for quality control and R&DLife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
Product
Informtest SAT
-
«Информтест САТ» - это инновационная, высокотехнологичная среда для разработки циклограмм, осуществления процессов моделирования и тестирования любых объектов контроля, не имеющая аналогов российского производства. Крупнейшие научные и производственные центры (РКК «Энергия», ОАО «ИСС» им. Академика М.Ф. Решетнева) уже используют данное программное обеспечение. Informtest Holding presents a unique software product "Automatic Testing System". This product eliminates the need to involve programmers in the development of open source software for testing and modeling, a CAD of the Informtest SAT shell and one specialist is enough. Thanks to an intuitive graphical interface, the development of any necessary sequence diagrams is not difficult even for a user unfamiliar with the basics of programming. The system is constantly being improved and updated. It is possible to make the necessary changes for each customer.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 470Ω
40-252-014
Programmable Resistor Module
The 40-252-014 is a programmable resistor module with 4 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Testing Cars and Trucks
-
Sun Test Systems develops, produces and installs high-quality testing equipment suitable for dynamic vehicle testing at the end of the production line.As a result of the long-term and intensive cooperation with our customers products have come into being with unique features such as high safety, great flexibility, optimal operational reliability and low costs during the long life span.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm
40-294-012
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 470Ω
40-251-114
Programmable Resistor Module
The 40-251-114 is a programmable resistor module with 4 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Test Database Software Module
-
The relational test database is the pivotal point of the software structure. On one hand, this is where the test applications and test systems used for productive testing are stored; on the other hand, it provides the storage space for all DUT-related test data. Depending on customer requirements, the test database may either be hosted locally on the test system or centrally on a server, supporting several test systems. The database performance is sufficient for a high-volume production environment with many test systems which access the central database in parallel. LXinstruments prefers to implement the database as a license-free MySQL database; it is however also possible to realize a version based on Microsoft SQL.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
-
Product
Analyser
Harmonics & Flicker
-
The Laplace Harmonics and Flicker analyser provides the user with a complete system for testing product compliance with IEC61000-3-2 and IEC61000-3-3.
-
Product
Testability Director
-
Advanced Test Engineering Solutions, Inc.
A spreadsheet template, which guides in the development of testable designs. It contains the Inherent Testability Checklist used with MIL-STD-2165, the U.S. Government''s Testability Program for Electronic Systems and Equipments. But Version 3.1 goes much further, bringing you hundreds of guidelines from IC design through board and system testing.
-
Product
Parallel Test Systems
-
Our parallel test systems for research and development are highly flexible in use and easily adaptable to different tasks as well as changing piezoelectric materials and designs.
-
Product
4/8 Channel Optimal Multiport Power Meter
UC8728
-
UC INSTRUMENTS UC8728 4/8 CHANNEL OPTICAL MULITIPORT POWER METER are PC control multiport passive components power meter test system and offer superior performance for the test of multichannel DWDM, WSS, ROADM, AWG & PLC components and modules, optical amplifiers, DWDM system and other general purpose of multiport fiber optical test and measurement applications. The system can be integrated with tunable laser source, optical attenuator & PDL controller provides a high performance passive components and modules automatic test system platform.
-
Product
Field Strength Analyzer
SRM-3006
-
Selective measurement of high frequency electromagnetic fields. Complete, easy to use test system, consisting of a base unit and measuring antennas, for non-directional detection of fields and their sources in the frequency range from 9 kHz to 6 GHz and from 24.25 GHz up to 29.50 GHz with 5G FR2 Antenna.
-
Product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
Test System
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
Product
System for Analyzing Door Handles
-
In the production process of a vehicle door handle, the electrical functions of the component are to be tested. The mechanical testing of the operation of the door handle is performed by a PLC-controlled test system. In addition to the mechanical test, the electrical parameters: “serial data stream” and “impedance of the antenna” are to be analysed.
