A/D Converters
quantization of an analog signal into a digital signal.
-
Product
RIM Modules
-
Curtiss-Wright Defense Solutions
In today’s market, customers are looking to maximize their I/O capabilities without adding extra hardware. The use of PMC or XMC mezzanine modules provides this ease of expansion.
-
Product
Mid-Range Chemiluminescence NO/NO2/NOX Analyzer
Model T200M
-
Teledyne Advanced Pollution Instrumentation
The Model T200M combines the proven chemiluminescence principle with a number of innovative features to provide reliable and repeatable NO, NO2, and NOx measurements for extractive type CEM systems. The option of either a molybdenum converter or a high-efficiency stainless steel thermal NO2 converter allows the T200M to be used in a variety of extractive CEM systems, from gas turbines to coal-fired boilers.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 16 Channels, 16 Single-Ended Inputs
DN2.592-16
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Frequency Converters
-
CAES offers a full range of custom frequency converter solutions including narrowband, wideband and block upconverters and downconverters.
-
Product
MOD MONITOR
TYPE HFX-1
-
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
Product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
-
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 3U VPX
Model 52690
-
- Accepts RF Signals from 925 to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal levels with up to 60 dB gain- Programmable analog downconverter provides I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
EDFA Optic Amplifiers
-
Wuhan Sunma Technology Co., Ltd.
With the feature of high input power, high output power, and medium optical gain, the booster amplifier operates at the transmission side of the link to amplify aggregated optical input power for reach extension.SunmaFiber booster amplifier is a low-noise, gain-flattened C-band optical erbium doped fiber amplifier (EDFA) designed to cost-effectively extend the optical link power budget for building long distance DWDM solutions.SunmaFiber also offers switches, routers and fiber converters including 10/100M, 10/100/1000M and 10G fiber converters, SFP fiber converters, manageable/unmanageable fiber converters, OEO fiber converters, POE fiber converters, fiber converter cards, and fiber converter chassis; transmitting distance from 2km(MM) to 150km(SM) with SC or LC or FC connectors.
-
Product
Charger and Low Voltage Power Supply
FlexiCharge FC1500
-
The FC1500 Medical Capacitor Charging power supply, with a built in configurable ACDC power supply is designed to provide the system power needs for Medical laser applications. The FC1500 can provide both capacitor charging and ACDC low voltage system power due to it’s unique design and intelligent control. The FC1500 can be used as a standalone capacitor charger, and if needed, various low voltage modules can be added to the unit to provide further system power. This functionality provides extra flexibility to power other systems and applications. Low voltage modules can be connected in parallel and in series for application that require higher voltage and current requirements. The Capacitor charger capabilities has the highest level of performance due the unique built in intelligent control for capacitor charging, higher charge rates and power limit control.
-
Product
Current Probes
-
Tektronix current probe solutions offer:*The broadest range of AC/DC and AC-only current probes*Measurement accuracy from uAs to 2000 A*Best-in-class bandwidth up to 120 MHz*Best-in-class current clamp sensitivity down to 1 mA*The only products with 3rd Party Safety Certification (UL, CSA, ETL)*The only products with bare wire voltage ratings*Automatic readout and scaling when used with Tektronix oscilloscopes so you don’t have to convert volts to amps or manually set the scaling
-
Product
In-line ICP® Charge Converters
-
In-line ICP® charge converters play a vital role in converting high impedance charge mode piezoelectric sensor signals into low impedance voltage signals, facilitating input to readout, recording, and analysis instruments. Specifically engineered for compatibility with high temperature piezoelectric sensors, these units are capable of operation in environments reaching up to 500°F (260°C). The series boasts ±2.5V or ±5.0 V output, offering a range of gain options, all packaged within a compact and durable casing. As a cost-effective alternative to laboratory charge amplifiers, in-line ICP® charge converters present an appealing choice for multi-channel applications.
-
Product
Synchro/Resolver Boosters
-
NAI offers a variety of multi-channel Synchro/Resolver Boosters that accept Synchro/Resolver inputs, and they deliver isolated outputs capable of driving passive and active loads such as Control Transformers or Torque Receivers. These amplifiers can be used stand-alone or in conjunction with Digital-to-Synchro/Resolver Converters.
-
Product
Coordinate Measuring Machines
-
Tokyo Seimitsu is the pioneer that developed “Japan’s first coordinate measuring machine.” We respond to every need with a varied lineup to which we have added Carl Zeiss products linked to our products.
-
Product
RH+T+Tdp Cable Probe
T3111-2
-
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
High Accuracy Fibre Optic Inertial Navigation System
SATURN INS
-
SATURN INS, from Teledyne TSS, is a world leading surface navigation system which offers enhanced unparalleled INS performance which builds on the TSS fibre optic gyro system by adding inertial navigation (INS) capability.As with SATURN, it is available in three standard heading accuracy variants; 0.1° sec lat (SATURN10INS), 0.3° sec lat (SATURN30INS) and 0.5° sec lat (SATURN50INS).
-
Product
Digital Synchro and Digital to Resolver
DSN-DRN
Digital / Synchro Converter
Computer Conversions Corporation
The DSN - DRN Series are highly reliable, miniature, narrow profile and low cost, continuously updating Digital Synchro and Digital to Resolver (AC Sine / Cosine) Converters designed for military and industrial control applications.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 32 Channels
DN6.593-32
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Pogos
-
AMETEK Sensors, Test & Calibration
The pogo system uses test frames fitted below the machine base to allow testing of very large samples up to 2 x 2 m (78.7 x 78.7 in) in size, with the added benefit of optional elevated and low temperature testing capacity.
-
Product
Digital Panel Meter
DPM
-
Digital panel meters are digital displays intended to be mounted in a panel, such as a control panel. They typically read some type of input, be it a voltage, current, or resistance, and display its value digitally. Often this input is a measurement from a sensor which is converted and displayed as a temperature, pressure, or other system variable. These meters may also act as simple controllers which trip a switch or perform a simple function when the reading reaches a preset measurement.
-
Product
2-Channel Front End
BEQ II.1
-
*Binaural, digital equalizer with 24 bit technology and USB interface.*The digital equalizer BEQ II.1 combines the characteristics of an equalizer, a two-channel front end and an A/D converter into one mobile and very versatile measurement tool.*Binaural, aurally-accurate recordings can be conducted easily with BEQ II. The AES/EBU interface allows a quick and easy expansion into a four-channel system, e.g. with the HMS III or HMS IV. Via the ADAT interface, up to four BEQ II units can be connected, allowing for eight-channel recordings.*Integrated signal conditioning allows common measurement sensors (Microphone, Line, ICP�) to be directly connected to the front end. In addition, separate pulse inputs are available e.g. for RPM data acquisition.*Thanks to the high-performance built-in battery - external DC power supply is also possible - and its low weight, BEQ II.1 is the ideal tool for either mobile or stationary operation.
-
Product
JadeFX FlexorSet 4-Ch 16-bit: 500 MHz A/D & 2 GHz D/A - 3U VPX
Model 5983-324
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex UltraScale FPGAs- Four 500 MHz 16-bit A/Ds- Four digital upconverters- Four 2 GHz 16-bit D/As (500 MHz input sample rate, 2 GHz output sample rate with interpolation- 4 and 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system referencePCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical interface for backplane gigabit serial interboard communication- LVDS connections to the Kintex UltraScale FPGA for custom I/O and sychronization- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)
-
Product
Flexible x1 PCI Express to PCI Adapter
SKU-041-0X
-
The Flexible x1 PCI Express to PCI Bus Adapter (Adapter) was designed to convert the x1 PCI Express bus into two 32-bit PCI buses. It allows you to connect up to two 32-bit PCI expansion boards to the motherboard x1/x4/x8/x16 PCI Express connector.The adapter includes a PCI adapter, x1 PCI Express host board and a PCI Express flat cable.
-
Product
10 Channel ADC FMC Module
ADCFN10-DC – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN10 is a ten channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Both AC and DC coupled input are supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
Product
Narrow Profile Power Supplies
DC-DC Converters
-
These state-of-the-art DC-DC converters combine excellent regulation and ripple specifications with broad input ranges, and they are available in a large selection of output voltages and current ratings. Accessory mounting kits permit easy installation on a vertical panel, wall or on a DIN rail.
-
Product
CAN Sensoy/ Interface
Strain
-
Reach Technologies' CAN Strain Sensor Interface sources, conditions and digitizes 8 strain sensor inputs for collection via CAN. The module is ideal for conveniently adding strain data to a distributed CAN network. The CAN Strain Sensor Interface is configurable via a CANopen stack.
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - 3UVPX
Model 54821
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Exceptional dynamic range/analog signal integrity- Xilinx® Kintex® UltraScale" FPGA- Compatible with several VITA standards including: VITA 66.5, VITA 67.2 and VITA 67.3C- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of 2400 DDR4 SDRAM- Programmable frequency synthesizedsample clock generator- Sample clock synchronization to an external system reference- Powerful DMA controllers for moving data- PCI Express (Gen. 1, 2 & 3) interface up to x8- Multi-channel synchronization with clock/sync bus- Optional clock/sync generator for multi-board systems- Optional gigabit serial links for custom FPGA I/O- Optional LVDS port and gigabit serial links for custom FPGA I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.5 GHz Bandwidth
M4X.2233-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Audio Content Management & Distribution
-
ATX is the worldwide leader in radio broadcast technology. The company’s field-proven XDS audio content management, distribution and monitoring platform enables all radio networks to deliver, schedule and playout live and pre-recorded audio, via satellite or the Internet, to radio stations throughout the world. The fully integrated, end-to-end XDS platform seamlessly manages localized ads, weather, news, and any other content over live and pre-recorded programing, as well as supports a centralized studio model. It is the most innovative, advanced, and cost-effective radio and audio broadcasting platform in the world.
-
Product
Shaker Systems
-
Vibration Research Corporation
Small force vibration testing equipment and shakers for product and modal analysis testing. Each system consists of a shaker and a matching linear direct-coupled power amplifier. Additional components may be added to the basic system to tailor it to your specific needs.
-
Product
DC-DC High Performance
CPC Chassis Mount Series
-
High performance DC-DC converters offer high efficiencies of 93% typical (12V model.) This high efficiency allows for minimal output current derating at elevated ambient temperatures.
