A/D Converters
quantization of an analog signal into a digital signal.
-
Product
4 Channel ADC FMC Module
ADCFN04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
Product
Digital Turn-to-Turn Tester
-
Shanghai Aoboor Electric Co., Ltd.
observe subtle changes in the rising edge of low inductance coil waveform in real time using hight speed A/D conversion technique.
-
Product
NI-5752, 50 MS/s, 12-Bit, 32-Channel Digitizer Adapter Module for FlexRIO
781357-01
Digitizer
The NI‑5752 is a digitizer adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a high-speed digitizer that simultaneously samples 32 channels at 50 MS/s. You can use the NI‑5752 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
1 GHz A/D and D/A with Virtex-6 FPGA - PCIe
Model 78630
-
Model 78630 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A highspeed data converter, it is suitable forconnection to HF or IF ports of a communications or radar system. Its built-in data capture and playback features offer an ideal turnkey solution as well as a platform for developing and deploying custom FPGA processing IP.
-
Product
Virtex 5 Based PXIe Board.
SMT700
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
Voltage Pulse Generator
SKS-IV10J
-
Shanghai Sanki Electronic Industries Co., Ltd.
The voltage pulse generator SKS-IV10J is completely designed in accordance with the requirements of the impulse voltage chapter in OIML R 46-1/-2; it meets the requirements of the new IEC60255-5 and GB14711 standards; the leakage current detection alarm function is added, and the leakage current limit can be Adjustment; using linearized high-voltage power supply, low noise, high stability, high voltage accuracy and long service life.
-
Product
Photometric Radiometric Transmitters
HD2021T Series
-
The serie HD2021T allows to convert photometric and radiometric quantities, such as illuminance (Lux) and irradiance (W/m²) in the UVA, UVB, UVC spectral regions and in the 400 … 1050nm band, into a 0 …10Vdc voltage signal. The series is suitable to be installed either indoor and outdoor.
-
Product
128 Channel Multihit TDC
VX1190A-2eSST
-
The VX1190A-2eSST is a 128 channel Multihit TDC, housed in a 1-unit wide VME64X 6U module. The unit features High Performance Time to Digital Converter chips developed by CERN. LSB can be set at 100 ps (19 bit resolution, 52 µs FSR), 200 ps (19 bit, 104 µs FSR) or 800 ps (17 bit, 104 µs FSR).
-
Product
Optical Fiber Cable Testing Equipment
-
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
Product
Signal Converters
-
The signal converters from HEIDENHAIN let you flexibly adapt the encoder signal interfaces to the requirements of your applications. For some applications, additional signals, such as from temperature sensors, are processed and forwarded to the subsequent electronics.
-
Product
Multisite Testing – Rail System
-
Mechanical system allowing the flexibility of multi-site testing with adjustable site to site spacing The Celadon Rail System allows multi-site testing capability with flexible die to die spacing using existing Celadon VersaTiles™ to minimize cost of test with new DUT structures. The modular design allows for additional site assemblies and rail assemblies to be added after the original system purchase. With the Celadon Light-Tight Enclosure and Rail System Tool, high accuracy alignment and testing can be performed at extreme temperatures without effecting the thermal equilibrium of the system.
-
-
Product
Scalar Mixer / Converter Measurements
S97082B
-
The S97082B scalar mixer/converter measurements enables the highest accuracy for scalar conversion–loss/gain measurements with a simple setup and calibration
-
Product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 4 Channels
M4i.4471-x8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them.
-
Product
Unipolar D/A Converters
-
Analog Devices offers the broadest portfolio of low voltage single-supply d/a converters in the industry, which includes many leading products in performance and package size. A wide variety of applications use ADI precision nanoDAC® products because of their small footprint and robust range of features, including 8- to 16-bit resolution, low power, a fast 50 MHz SPI or 3.4 MHz I2C interface, and more, in a tiny package option. ADI’s nanoDAC+® products offer enhanced features such as higher accuracy, improved dc performance, increased robustness, and lower glitch energy, among other advantages.
-
Product
ANSI X3.28 Interface Board
Model 4804B-7
-
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
Product
Temperature and Humidity Transmitter
T3319-2
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Platform
ATX7006A
-
The ATX7006A is a fully integrated solution for testing ADCs, DACs and other Analog functions. It combines very high accuracy, low noise and fast sampling with an exceptional ease of use. Traditionally data converters are tested using a whole stack of bench instruments, filters, switch matrices and user made software. Many engineering hours are needed to get reliable results. The ATX7006A is a single instrument for all your data converter testing and test methods.
-
Product
DC/DC Converter 4 W
20IMX4-2
-
Rugged BMP Melcher™ DC/DC converter | power 4.1 W | input 8.4 - 36 VDC
-
Product
Power Meters
-
Chroma Systems Solutions, Inc.
Chroma’s Digital Power Meters are designed for both single-phase and multiple phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits the 66200 Digital Power Meter uses state-of-the-art DSP digitizing technology. The internal 16 bits analog/digital converters with sampling rates of up to 200KHz provide both high speed and high accuracy measurements which is unprecedented within the industry for this class of power meters current on the market.
-
Product
Block Down-Converter
-
RF Lambda’s block down-converters are used to convert higher frequencies down to IF. They can include front end amplifiers for lower noise figure and signal conditioning such as image rejection as required by the system.
-
Product
PLCC-to-DIP Adaptor
Series 652000/653000
-
PLCC to DIP Adapter. Converts PLCC packaged ICs to DIP footprints. Ideal for prototyping and testing/evaluation. Available with PLCC sockets or PLCC pads on top side. Consult factory for panelized form or for mounting of consigned ICs.
-
Product
Web Sensor
T3511P-2
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Frequency to Current Converter
DAT4540R
-
The Frequency to Current converter DAT4540R is a signal conditioning din rail mount converter which converts a pulse input to an analog output equal to the set range which is selectable from 0.1 Hz up to 20 KHz. The DAT4540R also provides 2 relay outputs and a transistor output. The input can be from a Tacho, TTL, PNP transistor or from any Namur standard. The DAT4540R provides a Voltage or Current output that is isolated from the power supply and input.
-
Product
Telephone Test Sets
-
Telephone test sets are a standard among telephone linemen. For the past 100 years, a test set’s functionality hasn’t changed much. Times are changing, networks are changing and now butt sets are changing. No longer are they single-purpose tools but are evolving into full-fledged, multi-functional test sets. Enter Fluke Networks’ newest line of VDV (voice, data and video) telephone test sets. We’ve taken the best features from our existing line, added new technology and totally redesigned them to lighten up your tool belt.
-
Product
Network Management
-
PLANET Universal Network Management System is designed to monitor all kinds of deployed network devices, such as managed switches, media converters, routers, smart APs, VoIP phones, IP cameras, etc., compliant with the SNMP Protocol, ONVIF Protocol and PLANET Smart Discovery utility. It thus enables the administrator to centrally manage a network of up to 1024 nodes from a central office, greatly boosting network and power management efficiency. The NMS solution includes the software, hardware and Touch LCD controller series to attend to different applications. They all feature dashboard, topology and map viewing to make network management efficient and effective.
-
Product
2-Channel ADC Module
FMC161
-
Sundance Multiprocessor Technology Ltd.
The FMC161 provides one 12-bit A/D channel at 3.6Gsps or two A/D channels at 1.8Gsps clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC161 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
SparkFun Qwiic Pro Micro
USB-C (ATmega32U4)
-
Here at SparkFun, we refuse to leave 'good enough' alone. That's why we're adding to our line-up of Arduino-compatible microcontrollers once more! The SparkFun Qwiic Pro Micro is a revision of the original Pro Micro and is, overall, functionally the same as the previous version. The board is the same size as the original Pro Micro but we added a few additional features by shrinking down some components on the board such as a reset button, Qwiic connector, USB-C, and castellated pads (this makes it really handy for you custom keyboard creators out there)! Think the Pro Mini except with an ATmega32U4 on board and full USB functionality.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 3U VPX
Model 52690
-
- Accepts RF Signals from 925 to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal levels with up to 60 dB gain- Programmable analog downconverter provides I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Airborne Frequency Converter
AFC Series
-
Behlman’s AFC-7000-1 & -2 and AFC-7003, frequency converter are designed to convert three-phase aircraft power to regulated single-phase (115 or 230 VAC) or three-phase (115/200 VAC) at 50 Hz, 60 Hz or 400 Hz. They are ruggedly built to support aircraft takeoffs and landings and designed to meet the input power requirements of MIL-STD-704 and RTCA-DO-160.
