-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm
50-294-024
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Resistor Module 2-Channel 2R to 16.3k with SPDT
40-293-131
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Stability Walk-in Chambers
-
Stability walk-in rooms are an ESPEC North America specialty, designed for light-duty testing or long-term steady-state evaluation of pharmaceuticals and other products.
-
Product
Testing And Design Services
-
Rhein Tech Laboratories, Inc. (RTL) is a full-service design and compliance engineering test laboratory. We have grown with the industry from general purpose EMC testing into other areas of testing such as Radio (RF testing), Military and Aviation, Industrial, Scientific and Medical, Automotive, Electrical Safety, Shielding Effectiveness, Site Surveys and Radar Cross Section & High Range Resolution measurements.
-
Product
EPA General Purpose Probes
General Purpose Probe
General Purpose Spring Probe contact solutions are designed for high volume testing and feature the industry-proven Pylon line. General-purpose probes are offered in both replaceable and non-replaceable options.
-
Product
Optical Fiber Tensile Jig
-
This jig is designed for tensile testing optical fibers and other brittle fibers. The jig consists of upper and lower pneumatic flat grips with flat grip faces followed by large-diameter capstans.
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-04
Multifunction I/O
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
30A, 50 MHz High Sensitivity Current Probe - AC/DC, 30 A rms, 50 A Peak Pulse, 1.5 meter cable
CP030B
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 131k Ohm
40-294-034
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Auditor Torque Cube
ATC Series
-
The Auditor Torque Cube (ATC) is a compact, versatile desktop tester and provides a multitude of capabilities. The ATC is designed to test hand or power tools with the following: Peak, first peak and track modes. Multiple engineering units. Manual and auto clear function. Multiple frequency response settings. Bi-directional use and accuracy. Accuracy is better than 1% of indicated reading top 90% of range. Serial data output. Memory 999 data samples. Battery and/or mains powered.
-
Product
Transformer Turns Ratio Meter
TTRM 102
-
SCOPE introduces state of the art precision single phase Transformer Turns Ratio Meter (TTRM ) designed for field testing as well as factory testing of power transformers, instrument transformers and distribution transformers of all types. TTRM 102 along with turns ratio, measures ratio deviation, phase angle deviation, magnetizing current and detects tap-position of single phase transformer in charged switchyard condition. The range of AC voltage selection offers high accuracy in measurement.Both the instrument have in-built TFT display with touch screen and thermal printer. The user friendly, simple instrument makes the testing more easy. With the touch keypad it is possible to enter required DUT information.The ratio results are displayed with % error. Internal non-volatile memory gives the provision of storing test results.Further data can be downloaded to PC or copied to memory stick through USB port provided.
-
Product
Automatic Relay Test Set
DRTS 33
-
DRTS 33 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 3 Voltage generators simultaneously available.
-
Product
TACAN/DME Station Tester
EDST300
-
The R&S®EDST300 TACAN/DME station tester is an analyzer designed for commissioning, testing and servicing pulsed terrestrial navigation systems.
-
Product
PXI Resistor Module 2-Channel 1.5R to 8.19k with SPDT
40-293-124
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Radio Frequency (RF) Generators
-
Find and fix design problems during developmental testing. Viasat’s RF signal environment generation surpasses ordinary simulation and computer modeling techniques to deliver a true-to-life, dense avionics environment for the most accurate analysis of RF communication system performance.
-
Product
64-Channel Boundary-Scan Digital I/O Scan Module
JT 2111/MPV DIOS IDC
Digital I/O
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.
-
Product
Wristat Tester
WT25
-
The WT25 WRISTAT Tester is designed to test the integrity of our WRISTAT in a fast, efficient and simple manner. All of the elements of the WRISTAT - continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact are easily confirmed by pressing the top cover of the WT25. The operator (wearer) is tested for a resistance to ground of greater than 750K ohms and less than 10M (switchable to 100M ohms).
-
Product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Midi Rack 120*60*80cm
OTP2 module no.002
-
The rack serves as the basic structure for your individually designed test system. Various OTP² modules can be installed in the 120 x 60 x 80 cm rack in order to implement a wide variety of test requirements.
-
Product
PCI Express 5.0 and Compute Express Link Protocol Exerciser
Summit Z516
-
The Summit Z516 is a PCIe 5.0 and CXL protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z516 can emulate PCI Express 5.0 and CXL root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
Product
Ionic Contamination Test System
Omegameter SMD 650
-
The SCS Omegameter SMD 650, the long-time industry standard for ionic testing utilizing “static test” methodology, is designed to perform cleanliness testing on printed circuits and assemblies. Identifies the presence of ionic contamination on bare and assembled printed circuit boards and other electronic components. Provides an accurate and repeatable method for determining cleanliness on site. Provides immediate process control results, eliminating the need for outside laboratory testing.
-
Product
Dial Torque Screwdrivers
-
A dial measuring torque screwdriver is designed for torque testing and torque verification. It is a versatile tool that is utilized for torque auditing and product evaluation. It can be used to monitor torque as it increases or decreases or display peak torque applied. The dial screwdriver is used in two common torque verification tests. One is the first movement test and the second is the loosening test. The screwdriver is standard instrument in engineer’s tool kit.
-
Product
Handheld OTDR
SAT-18C
-
Shaanxi Aitelong Technology Co., Ltd
SAT-18C handheld OTDR is the newest instrument designed for testing FTTx network. It is mainly used to measure the physical characteristics of optical fiber, such as the length, the transmission loss and the splice loss etc. It can also locate the faults or breaks of optical fiber. It is widely applied in the manufacture, construction and maintenance in optical fiber communication system.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm - SPST
40-294-133
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Mixed Signal Test Systems
MTS2010i
-
The MTS-2010i are a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
Product
Walk-In Aging Chamber
-
Aging Chamber has been designed to simulate environmental condition to test the stability and reliability of products under stressed environment. Weiber is a leading manufacturer and supplier of Aging Test Chamber in India and abroad. Weiber offers scientific equipments at the most economical rates and versatile design. Microprocessor based Aging Test Chambers are made in accordance with the international testing standards. The equipments are NABL, NSF certified and CE approved. Aging Chamber maintains 25% to 95 % RH. The Test Chamber is digitally controlled delivering accurate result under controlled environmental conditions.
-
Product
Solar Spectrum Test Chamber / Solar Radiation Test Chamber
-
WEIBER Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. Weiber provide Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Weiber provide Solar Simulation Test Chamber.
-
Product
Fuel Tank Chamber
-
CSZ's fuel tank test chamber is designed to test the quality and reliability of automotive fuel tanks. Fuel tanks are temperature conditioned to -40C (-40F) along with a glycol mixture that is also chilled to -40C (-40F). The fuel tanks are filled with the glycol fluid and placed into the -40C (-40F) chamber. Tanks are soaked in the chamber for a predetermined length of time, removed from the chamber, raised to a specific height, and then dropped.
-
Product
PXI Signal Generators (Signal Sources)
Vector Signal Generator
Accelerate test throughput with fast, high-quality measurements optimized for RF or microwave design validation & manufacturing testIncrease test configuration flexibility with a PXI platform and license key upgradesReduce development time with easy integration of drivers and programming examples into test environments
