-
Product
Automatic Relay Test Set
DRTS 34
-
DRTS 34 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 4 Voltage generators simultaneously available.
-
Product
Combustion Leak Tester
AC560000
-
Fast, economical and accurate method to test for combustion gas leaks in head gaskets, cylinder heads and engine blocks. Dual chamber design provides more accurate test results. Test fluid can be used for both gasoline and diesel engines.
-
Product
Acoustic Imager
-
Can be used for quick on-site testing of current transformers in metering installations. They are designed and manufactured to test transformers’ primary current, secondary current, and turns ratio and identifies phase type and polarity.
-
Product
Motorcycle Battery Testers
-
ELAK Motor-Cycle Battery Testers are designed for testing batteries used in motor-cycles, scooters, ATV''s, etc. These testers check the voltage drop of the battery under a fixed load and confirm the status of the battery full, weak or dead. The new generation motor-cycle and scooters are fitted with an electrical start. It is therefore very essential to test these batteries under load, to ensure that the batteries are capable of starting the vehicle.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 1.02k Ohm With SPDT
50-293-121
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXIe Digital Stimulus/Response with PPMU: 250 MHz, 16 Channels
M9195B
Digital I/O
The Keysight M9195B PXIe digital stimulus/response (PXI DSR) module is ideal for IC design validation and production test environments. The PXI DSR provides 16 bi-directional digital channels with programmable logic levels and can be configured for synchronized cyclized digital data, for parametric measurements, or for static digital IO.
-
Product
SAS
-
SCHILLER AUTOMATION GmbH & Co. KG
The Gen4 Mini-SAS HD adapter kit will facilitate compliance testing for SAS-4 host, device, and cable. The left and right-hand version plug adapters are designed to test side-by-side.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 4.09k Ohm
50-293-023
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm - SPST
40-294-122
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Benchtop Communication Test System
ATS3000A
Test System
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 65.5k Ohm - SPST
50-294-133
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 127 Ohm
50-293-012
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Haze Meters
-
Shenzhen ThreeNH Technology Co., Ltd.
3NH offers a wide range of haze meters. They include various benchtop and portable models. Our haze meters are specially designed for testing haze, transmittance, and clarity in glass, plastics, films, and transparent packaging materials.
-
Product
Melting Point Testers
-
These melting point testers are designed to accurately test the melting point of medium used in thermometers, for educational purposes, for quality control, automated process and more.
-
Product
Benchtop Discrete Component Tester
Imapact 7BT
-
The 7BT Benchtop Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The 7BT automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability.
-
Product
Automatic Electrical Protective Equipment Test Systems
CBC-50С (CBC-100C)
-
Automatic systems CBC-C-series are designed for high-voltage withstand testing of electrical protective equipment and insulated hand tools. The tests are carried out with AC voltage (CBC-50C: UAC ≤ 50 kVRMS; CBC-100C: UAC ≤ 100 kVRMS) at industrial frequency (f = 50 Hz).
-
Product
PXI Multiplexer, Very High Power DC, 4-Channel, 20A, 28V
40-664A-002
Multiplexer Module
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
Product
Vacuum Leak Tester
MFY-CM
-
Saicheng Vacuum Leak Tester (also called Leak Detector, Leak Test Apparatus) is professionally designed for the leakage tests of packages, bottles & pouches for food, drugs, medical instruments, household chemical products, cars, electronic components, stationeries and other industrial products. The instrument also can be used to test seal performance of specimens after falling and compression tests.
-
Product
Rugged Igniter Tester
4314 KV
-
Model 4314 KV is a 4-wire ohmmeter designed to use low test currents for its measurement. Additional circuitry proprietary to Valhalla Scientific is used to ensure that test current levels do not exceed the specified “fail-safe current” even in a worst-case component failure situation.
-
Product
Tactical Grade Inertial Measurement Unit (IMU)
ADIS16490 iSensor
-
The ADIS16490 iSensor® device is a complete inertial system that includes a triaxial gyroscope and a triaxial accelerometer. Each inertial sensor in the ADIS16490 combines industry-leading iMEMS® technology with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, and linear acceleration (gyroscope bias). As a result, each sensor has its own dynamic compensation formulas that provide accurate sensor measurements. The ADIS16490 provides a simple, cost-effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The SPI and register structure provide a simple interface for data collection and configuration control.
-
Product
Three Phase Closed I-P Link Energy Meter Test Bench Type KP-S3000-B
-
Bofa Instrument & Equipment Co., Ltd
Three phase closed I-P link energy meter test bench, type KP-S3000-B, is designed for testing three-phase energy meters, especially for testing Closed I-P Links three-phase energy meters. It is an ideal testing equipment for energy meter factory or R&D institute. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
RF/Microwave ATE Systems
-
Over two decades ago, In-Phase Technologies founded our company for the purpose of designing and producing reliable high quality RF and microwave Automated Test Equipment (ATE). We continue that tradition today, providing the best, world-class automated test equipment. Our system designs bring together the right combination of Commercial Off the Shelf (COTS) test equipment, custom designed and built Interface Test Adapters (ITAs), lightning fast and accurate measurement software, and the optimum user interface to make all of this technology easy to use.
-
Product
Testing Multi-Radio Mobile Devices
IQxstream
-
With LitePoint's IQxstreamTM mobile test system you will have all the capability you need to fully test many 3G and even 4G cellular radios and standards. Moreover, the system is designed to reduce per-device test time and cost because of its unique parallelism architecture. A 100 MHz capture capability means that it can test adjacent channel leakage ratios (ACLR) in one, five-channel capture.
-
Product
DC Power Supplies
XG 1500
-
AMETEK Programmable Power, Inc.
The XG 1500 is an industry leading programmable DC power supply designed for test, production, laboratory, OEM and quality assurance applications. The XG 1500 is a 1500 Watt, 1U programmable power supply with constant voltage and constant current modes, automatic cross-over and numerous features enabling cost effective, easy integration.
-
Product
N Test Finger Nail
TF-24 series
-
Are designed to perform tests specified in many standards to determine compliance with safety requirements.
-
Product
Qualified Hermetic EGT Thermocouple Upgrade
-
FIT-IT & FORGET-IT Eliminate Exhaust Gas Temperature (EGT) thermocouple concerns with AMETEK's new EGT thermocouple product offering for Frame turbine applications. AMETEK has worked closely with the turbine OEM to design and engine test this thermocouple as a direct replacement and upgrade for all new and existing EGT thermocouples. The new EGT thermocouples are qualified and meet all design specifications.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm With SPDT
50-293-131
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Dual Programmable PSU, DC Input
41-740-001
Programmable Power Supply
This PXI dual programmable power supply module is designed specifically for test applications that demand precision output voltage/current and tightly coupled measurement capabilities. Its versatile design makes it ideal for a broad range of testing applications in markets as diverse as communications, aerospace, and automotive manufacturing.
-
Product
Electromagnetic Environmental Effects
EEE
-
Electromagnetic Environmental Effects Services provides engineering design and test implementation for Electromagnetic Interference and Compatibility (EMI/EMC), along with TEMPEST capabilities certified under the National Security Agency (NSA) TEMPEST Endorsement Program.
-
Product
Melting Point Testers
-
These melting point testers are designed to accurately test the melting point of medium used in thermometers, for educational purposes, for quality control, automated process and more.
