-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
Desktop Appliance for PCI Express® Gen4
DE200-G4
-
A versatile test system designed to test and debug solid state drives (SSDs) of all popular storage interfaces and protocols, such as PCIe, SAS, and SATA.
-
Product
Qualified Hermetic EGT Thermocouple Upgrade
-
FIT-IT & FORGET-IT Eliminate Exhaust Gas Temperature (EGT) thermocouple concerns with AMETEK's new EGT thermocouple product offering for Frame turbine applications. AMETEK has worked closely with the turbine OEM to design and engine test this thermocouple as a direct replacement and upgrade for all new and existing EGT thermocouples. The new EGT thermocouples are qualified and meet all design specifications.
-
Product
DC Blocks From 0.1 MHz To 18 GHz
-
Pulsar Microwave Corporation's DC blocks are designed to inner-only topology and utilize our standard housings for fast turn manufacturing. Designs are tested to 50 Ohms, and models range up to 18 Ghz with a maximum voltage rating of 500 Vdc.
-
Product
24-Bit Precision Load Cell Input Card
PCI-9524
Analog Input Module
The PCI-9524 is a robust, multi-purpose module designed for turnkey material test systems (MTS). Equipped with four strain gauge-based transducer input channels, four general purpose analog input channels, and a 3-axis motion controller, the PCI-9524 delivers a complete hardware solution for MTS manufacturers. The PCI-9524 easily integrates physical quantity measurement and implements strategy of close-loop control in a single module package. For transducer measurement, the PCI-9524 supports sensitivity from 1.0 mV/V to 4.0 mV/V and provides a 1/200000 accuracy of measurement of full scale. These features make the PCI-9524 suitable for precise measurement in large-scale transducers.
-
Product
MCB Temperature Rise and Power Loss Test Bench
-
The SCR Elektroniks 3 station MCB Temperature Rise and Power Loss Test Bench is economically designed to verify temperature rise and measure power loss as per clause 9.8 of IEC 60898 with the circuit designed to follow test procedure as per Cl 9.8.2. The temperature rise is measured in accordance with Cl 9.8.3 and 9.8.4 while power loss is measured and verified as per Table 15 of Cl 9.8.5.
-
Product
Digital Battery Testers
-
Electronic devices designed to test the remaining capacity of a battery's overall charge.
-
Product
PXI Resistor Module 2-Channel 2R to 16.3k with SPDT
40-293-131
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Portable Hardness Tester
PHT-1800
-
State of the art, digital portable hardness tester is designed to test the hardness of large hard metal parts. Loaded with useful functions only found on high priced models the PHT-1800 portable hardness tester is clearly setting a new industry standard by being the most accurate, economically priced portable hardness tester on the market today.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm
40-294-012
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXIe-4051 - PXIe, 1-Channel, 60 V, 40 A PXI Electronic Load Module
788179-01
Load Module
The PXIe-4051 provides programmable load capable of sinking DC power for characterization, design validation, and manufacturing test. This module helps you sink current and absorb power out of a power source up to 300 W with programmable constant voltage, current, resistance, and power levels. You can use the PXIe-4051 to streamline the task of designing automated test systems for a wide range of applications—from aerospace and defense to automotive and semiconductor component test—by eliminating the need to mix multiple instrumentation form factors in a given test system and simplifying synchronization.
-
Product
Magnetic Probing Systems
MPS-C-300 and MPS-C-350
-
MicroXact’s truly unique patent-pending design enables wafer-level testing of spintronic devices, nanoscale electronics and many other materials and devices where magnetic fields are required for accurate test and measurement.
-
Product
Multifunction Substation Test Set
STS 5000
-
STS 5000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
Product
TestBench & Planar Biaxial Test Instruments
-
TestBench configurations were designed with component testing in mind, and thanks to their modular approach, a wide array of configurations and performance capabilities are possible. TestBench systems can be multi-channel and multi-axis, including planar biaxial testing.
-
Product
Pulsed Withstand Voltage Safety Test
-
Suzhou 3ctest Electronic Co.,Ltd.
designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment),
-
Product
Naturally-Aspirated/EVAP Automobile Diagnostics
-
Diagnostic leak detection equipment specifically designed for EVAP testing naturally-aspirated automobiles and light-duty trucks.
-
Product
Constant Volume Sampler
CVS-ONE
-
The CVS-ONE series is designed for the measurement of diluted emissions from vehicles and engines. The new integrated operating platform, HORIBA ONE PLATFORM is adopted for the CVS-ONE. The hardware has been significantly downsized from previous designs, reducing test cell footprint requirements. It introduces new functions and is more user-friendly, while still maintaining high accuracy. In conjunction with the MEXA-ONE (Motor Exhaust Gas Analyzer), the system can be used to measure extremely low emission levels such as SULEV. The new CVS reliably supports emission testing requirements of today and into the future.
-
Product
Telecom Transmission Tests
-
Networked Communication Solutions, LLC
Is designed to test across the full bands of T1-Lite® or E1-Lite® or test individual timeslots.
-
Product
PXI Resistor Module 4-Channel 1R to 63.7R
40-293-011
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 40Amp 14Volt 2xSPDT Automotive Relay
40-181-001
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Towing Dynamometer
RS-25K
-
RS-25K Towing Dynamometer is designed for testing today’s full-sized SUVs and light trucks. The RS-25K is built with a heavy-duty steel frame, an aerodynamic body and rides on an independent, air ride suspension using two eddy current absorbers with special high temperature coils to absorb energy. The RS-25K is powered by an industrial generator so there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm
40-294-033
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Programmable DC Electronic Load
DL3000
-
The DL3000 series is a cost-effective, economical programmable DC electronic load with a friendly human-machine interface and excellent performance specifications. It provides a variety of remote communication interfaces to meet diverse testing needs for design and testing. A wide range of solutions are available for a wide range of industries including automotive electronics and fuel cells.
-
Product
Signal Generators
-
Are electronic devices that generate repeating or non-repeating electronic signals (in either the analog or digital domains). They are generally used in designing, testing, troubleshooting, and repairing electronic or electroacoustic devices; though they often have artistic uses as well.
-
Product
RF Shielded Chamber
MIL-STD
-
A high performance RF-shielded chamber specifically designed for radiated emissions testing in accordance with MIL-STD-461E/F. This chamber can be used for conducted emissions, conducted immunity, radiated emissions, and radiated immunity testing.
-
Product
High Temperature Anemometer
6162 Series
-
The Model 6162 is a unique anemometer designed for specialized high-temperature testing.
-
Product
Load Cell Power Supply Module
MODEL PSM-F10
-
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
Product
In-Circuit Test
-
Test Coach has been delivering the highest quality in-circuit test programs since 1998. Our engineers have the education, experience and expertise needed to solve your most challenging test requirements. We partner with our customers to provide comprehensive test solutions, including consulting on: design for test, recommendations on the best hardware and software options to implement, test strategy, and long term planning for multi board projects. Our expertise allows us to really understand customer requirements, so that quotes are accurate and timely. However, we also understand that sometimes projects can change scope. At Test Coach, we have the flexibility to adapt to changes with as little impact to delivery as possible.
-
Product
Defect Isolation
-
*Traverse through the physical design to trace nets and vias down to the defect location*Utilizes industry standard LEF/DEF design files, scan-based test information, tester fail logs and diagnostic reports to determine and isolate the physical defect location*Enables the user to leverage their diagnostic experience to determine the root cause of the defect*Interactive layout viewer displays scan chains, mapped mismatches of scan cells, layers, nets and subnets with search capabilities(component, net, cell)*Physical XY coordinates are always displayed for components and nets to guide the user through the design to quickly identify suspect sites for FA using techniques like Emission, OBIRCH, LIVA, TIVA, or FIB
-
Product
Film Permeability Tester
-
Film Permeability Tester is designed to test the permeability of a wide range of packaging materials such as plastic film, composite film, aluminum foil, thin sheets, rubber, porcelain, medical patch, etc.
