Wafer Resistivity
See Also: Wafer, Wafer Thickness, Wafer Failure Analysis, Wafer Edge, Wafer Mapping, Wafer Probes, Wafer Probers, Wafer Inspection, Four Point Probes
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
Concrete Bulk Resistivity
RCON
-
Giatec RCON™ is a non-destructive device for measuring the electrical resistivity of concrete specimens in the laboratory without any additional sample preparation requirements. This measurement can easily be made on the same concrete samples that are currently used for the compressive strength testing of concrete.
-
Product
Resistivity Meters
-
Precisely Measure Surface Resistivity, Volume Resistivity, or Resistance to Ground. Advanced Energy's Trek and Monroe resistivity meters offer accurate and repeatable measurements for surface resistivity, volume resistivity, or resistance to the ground.
-
Product
Earth Resistance Clamp Meter
T2100
-
Clamp meters for measuring earth resistance directly on earth rods (STAKELESS METHOD) and compatible with MacrotestG series meters
-
Product
Wafer Inspection Machine
IV-W2000
-
The IV-W2000 is a wafer inspection machine that features on-the-fly scanning and inspection as well as automatic handling of 6/8/12-inch wafers. With the option to have a Chinese language UI, this machine is also known for being intuitive and user-friendly.
-
Product
Wafer Bonder
AML
-
Wafer bonding has found many applications in the field of MST, MEMS and micro engineering. These include the fabrication of pressure sensors, accelerometers, micro-pumps and other fluid handling devices. The process is also used for first-order packaging of silicon microstructures to isolate package-induced stresses. The OAI AML Wafer Bonder facilitates both the alignment and bonding to be performed in-situ, in a high vacuum chamber. For anodic bonding the wafers are loaded cold and heated in the process chamber. For high accuracy alignment the wafers are aligned and brought into contact only after the process temperature has been reached, thus avoiding differential thermal expansion effects which can compromise alignment. The AML Wafer Bonder is excellent for anodic bonding, silicon direct and thermal compression bonding applications. These features enable the bonder to be used with virtually any processing tool.
-
Product
PE/ Ground, Insulation Resistance Tester
Handheld
-
The safety testers of the Handheld class are used to measure PE/ Ground resistances, insulation resistances and to perform a simple functional test. The small and sturdy universal testers are intended for standard-compliant safety tests in workshops and production as well as for mobile operation during repair, installation, service and more.
-
Product
Built For Demanding Environments, The AIM-77S Rugged Case Delivers Reliable Protection With Drop Resistance Up To 120 Cm Onto Plywood.
AIM-77S Rugged Case
-
Operating Temperature: 0°C ~ 40°C (32°F ~ 104°F)Storage Temperature: -10°C ~ 60°C (14°F ~ 140°F)Humidity: 90% @40°C (non-condensing)Drop Protection: up to 120cm onto plywood
-
Product
Transformer Winding Resistance Meter
10A
-
*10A DC continuous current in 4 ranges of 0.01A, 0.1A, 1A and 10A.*4 ½ digit display for higher resolution.*Dual channel measurement.*Suitable for operation in energized switchyard conditions.*Specialized protection circuits for suppression of inductive voltage kickback.*SMPS based - lightweight and portable.
-
Product
Measuring Earth Resistance
OSP-510
-
Additional equipment to measure the earth resistance and soil resistivity AD-510.
-
Product
15" XGA Industrial Monitor With Resistive Touchscreen And VGA / HDMI Port
FPM-1150G
-
15" XGA TFT LED LCD with 70,000 backlight life timeRobust design with aluminum front panelSupports VGA or HDMI interface with USB touchscreenSupports panel, wall, desktop, or VESA arm mountingLockable HDMI port (optional)
-
Product
5 Kv Insulation Resistance Testers Sonel Mic 5010 Mic 5005
-
Sonel (Poland) make Digital Insulation Resistance Tester, Range: 0-5kV/15 TeraOhms with PI and Dar.
-
Product
Battery Internal Resistance Tester
HDGC-3915
-
HD Power Test Equipment Co.ltd
Battery Internal Resistance Tester is designed using the advanced AC discharge measurement method to test accurately voltage and resistance of battery. It is strictly designed to evaluate battery performance, state and life-time, which maintain all stationary power systems including Uninterruptible Power System. Battery Internal Resistance Tester can proceed the measurement in a group and in a single section of battery. With accurate testing of resistance and voltage, it gives an indication of battery capacity and technical status. The measurement data can be read on the instrument display directly. And it can also be uploaded to PC simply by using the USB drive. With the analyzing software, you could not only keep a record of the testing result but also have detailed analyzing for the status of batteries in different testing conditions.
-
Product
Low Resistance Metal Film Chip Resistor
RTX
-
This specification is applicable to lead and halogen free RTX series low resistance metal film chip resistors. Lead free products mean lead free termination meets RoHS requirement.
-
Product
Safety Shoe Electrical Resistance Tester
UI-FT06
-
Safety Shoe Electrical Resistance Tester is to test the electrical resistance of conductive footwear and antistatic footwear.
-
Product
Wafer Mapping Sensor
M-DW1
-
Panasonic Industrial Devices Sales Company of America
To provide better safety and improved sensing accuracy, Panasonic studied the requirements for future Wafer Mapping Sensors to ultimately develop the LED Beam Reflective Type Wafer Mapping Sensor, M-DW1. This Sensor uses LEDs as a light source for safe operation and a 2-segment receiving element for higher accuracy in wafer detection.
-
Product
DIGITAL DC RESISTANCE METER
VE2516BU
-
Micro Processor based DC Resistance Meter with PASS / FAIL indication.
-
Product
Battery Resistance Tester
BT-3915
-
Kongter Test & Measurement Co., Limited
Regular test of battery internal resistance or battery conductance is essential for stationary batteries. It is also recommended by latest regulation of IEEE 450, IEEE 1188 and IEEE 1106. The excellent performance of BT-3915 for testing battery internal resistance and voltage will help you pick out the weak batteries and ensure their performance in short time measurement.
-
Product
2-Channel Resistivity Meter
HE-960RW-GC(W)
-
The HE-960RW-GC(W) is a 2-channel simultaneous-measurement carbon sensor, resistivity meter that can be connected with two sensors. The measurement range is: 0 - 100.0 MΩ・cm.The high performance and high precision is maintained while simultaneously measuring the output of the resistivity of different two locations. This is carried out in a single converter for overall cost efficient performance.
-
Product
3 Wire (Digital) Earth Resistance Tester
1620 ER
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures earth resistance in three ranges : 40Ω, 400Ω, 4kΩ.● Capable of measuring earth voltage.● 3 ¾ digit (4000 counts).● LCD backlight display.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Data hold function.● Relative function.● Auto power-off function.● Low battery indication.● Calibration performed with supplied test leads.
-
Product
Wafer Prober Networking System
PN-300
-
The Wafer Prober Networking System PN-300 utilizes a database to facilitate data access from other systems and provides an environment that enables the user to edit data and handle processing. The system achieves wide-ranging compatibility by adopting standard hardware and operating system. In addition, it is equipped with an N-PAF (Network-based Prober Advanced Function) to provide robust support for wafer prober operation and maintenance.
-
Product
Winding Resistance Test
20A DC booster
-
The 20A DC STCS booster allows to perform resistance tests on a PT with a current up to 20 A DC. The option is used together with STS 5000 and STS 4000 and must be connected to STCS module.
-
Product
ESD LCD SURFACE RESISTIVITY METER (WITH 1 PAIR OF 5 POUND ELECTRODES)
-
The ESD LCD SURFACE RESISTIVITY METER provides everything necessary to test work surfaces using the procedure outlined in the EOS/ESD-S4.1 standard. This test kit makes testing surface resistance easy – simply place the weights attach the cables, switch to the correct voltage and press the button to read resistance directly on the meter. The meter incorporates parallel probes on the bottom of the unit which allows the user to make surface resistivity measurements. The parallel probes allow for quick and easy testing of a variety of surfaces and materials, without the use of the five pound electrodes
-
Product
[5kV AC/6kV DC] Hipot and Insulation Resistance Tester, Rise/Fall-Time Control Function Equipped
TOS5300 Series
-
The "TOS5300 Series" is a series of test instruments used in Hipot (withstanding voltage) tests and insulation resistance tests, two of the four tests regarded as necessary for ensuring the safety of electrical products. With an output of 5 kV/100 mA (AC) and 6 kV/10 mA (DC), the series can be used in Hipot (withstanding voltage) & insulation resistance testing of electronic equipment and electronic parts, based on the requirements of IEC, EN, UL, VDE, JIS, and other international safety standards and the Electrical Appliance and Material Safety Law. Also, the test voltage stability is improved with the adoption of a newly developed switching amplifier. Since the output voltage can be kept constant even when the AC line voltage or frequency changes, consistent testing can be performed, even when the power supply environment is in an unstable region. The TOS5300 is also equipped with a number of features that are capable of meeting a variety of test needs. It is a new low-cost standard model that provides thorough operability, reliability and safety.
-
Product
TRA-300 LED Thermal Resistance Structure Analyzer
-
Hangzhou Everfine Photo-E-Info Co., LTD
The TRA-300 accurately measures the thermal resistance, junction temperature, optical power, voltage, current and other parameters of LED packaging products.The heating and cooling curves of LED can also be obtained, and the integral and differential thermal structure functions can be obtained by establishing the finite element model.Through the structural function analysis of the TRA-300 special software, the fine thermal resistance structure of the LED (from the chip to the thermal resistance value of each package structure) can be obtained, so as to objectively evaluate the heat dissipation quality and thermal management level of the LED package products, and provide the best verification for the heat dissipation design of the LED.
-
-
Product
Digital Surface Resistance Meter
-
NEW Enclosure with Rubber Grip EdgesThinner and narrower design is easier to hold and provides protection from drops.NEW Quick Check ButtonBypasses the 15 second electrification period to allow quick spot checks.NEW Battery Compartment
-
Product
Low Resistance Or Continuity Testing
-
From Megger, these highly accurate, easy to operate instruments measure resistance with resolution as fine as 0.1 micro-ohm. Digital micro-ohmeters and DLROs measure contact resistance of switch and circuit breakers, aircraft frame bonds, and rail and pipeline bonds just to name a few of the applications. Megger has models available for testing using test currents from 0.5 mA to 200 amps covering a multitude of applications that require precise low-resistance measurements.
-
-
Product
Explosion Resistant Ovens For Flammable Solvents
-
Explosion-resistant ovens are designed to safely operate in environments that require extra precautions when working with flammable solvents.
