-
Product
Probes
-
SHOCONA Probes are designed for non-vibrating, contact mode applications and are compatible with most commercially available SPMs/AFMs. These probes are nanofabricated using highly doped single crystal silicon with unparalleled reproducibility, robustness and sharpness for consistent high resolution imaging capabilities. This is a box of 10 probes.
-
Product
Dual Trace Analog Oscilloscope With Probes
2120C
-
B&K Precision's model 2120C is a dual trace oscilloscope that offers high performance at a low price. Most competitor's entry level oscilloscopes have a 20 MHz bandwidth, while B&K Precision's models 2120C has a bandwidth of 30 MHz. This oscilloscope is built by and backed by B&K Precision, a company that has been selling reliable, durable, value priced test instruments for over 60 years.
-
Product
Temperature Probes
-
Our Temperature Probes are ideal for the Instrumentation, medical, communication, machine builder and HVAC industries.
-
-
Product
SICRAM Module Pressure Probes
PP471
-
Module to connect pressure measuring instruments to pressure probes.
-
Product
Semi-Rigid Test Probes Up to 6 GHz
-
Fairview Microwave’s semi-rigid test probe assemblies come in multiple cable diameters to help when attaching the unterminated end of the probe to a circuit board trace. There are two versions including straight-cut probe ends for those that would like to customize the dimensions of the center conductor and dielectric dimensions, as well as pre-stripped probe ends that are ready for immediate use. By soldering the outer conductor to the signal ground and the exposed center conductor to the trace carrying the signal of interest, simple sampling measurements can be made without having to create a separate subassembly circuit board or add a connector to the circuit layout which can take up valuable real estate. Fairview provides 3 diameters of semi-rigid coax and 3 different lengths from 3 inches to 12 inches to fit a variety of trace widths and applications. All test probes are 100% RF tested to ensure the cable assemblies operate to 6 GHz and also to make sure that the SMA connector interface meets the 1.35:1 VSWR specification prior to shipping. To protect the small diameter coax from damage, each part is shipped in a clear protective tube that can also be used for storing the probes for future use.
-
Product
HPA-74 General Purpose Probes
-
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Test Center Remark: max. test center 187 mil / 4,74 mmFull Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 75Recommended Travel (mm): 1.91Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 598Overall Length (mm): 15.19Overall Length Remark: Tip “A-B”: 598 (mil), 15.19 (mil), Tip “C”: 586 (mil), 14.88 (mil), Tip “E, T135, T156, T65, T80”: 610 (mil), 15.49 (mil), Tip “T75”: 620 (mil), 15.75 (mil)
-
Product
Probes
70 Series
-
American Probe & Technologies, Inc.
The series is for all probes that are non-standard in shank diameter (other than 10 or 20 mil).
-
Product
General Purpose Probes
PIT-12
-
PIT-12 General Purpose Probe for Pressurized Systems - 12'' #304 stainless steel shaft. Diameter is 1/16''. Immersible. Maximum temperature 350°C, Time constant 0.5 Seconds. Shaft Terminated in a sub-miniature Type T Thermocouple plug. 10 foot Sub Miniature Type T extension lead supplied. Not isolated.
-
Product
Probes Dissolved Oxygen
-
Specialized, in-line sensors that provide real-time, continuous monitoring of oxygen levels in liquid.
-
Product
ICT Probes
Merica Serirs- MP175
-
Minimum Center: 1.91mm (75mil)Current Rating: 3amps, continuousContact Resistance: 40milliohmsMounting Holes Size: 1.35Full Stroke: 6.40mmRated Stroke:4.30mmSpring Force: 203gf (7.2oz)/227gf(8oz)
-
Product
T3 Low & High Voltage Differential Probes
T3 Series
-
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
Product
Micro probes 1 MHz up to 1 GHz
MFA 02 set
-
The two in the set included micro probes are used to measure low-frequency magnetic fields up to 1 GHz, e.g. at signal conductors (150µm), SMD componets (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the BT 706 Bias tee. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee to a spectrum analyzer or an oscilloscope. The MFA 02 set delivery of Langer EMV-Technik GmbH includes correction lines. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
Product
Bead Target Probes
-
A methodology for placing test points directly on a PCB's copper traces, or top metal, thus forming a “Bead Probe”.
-
Product
Near Field Probes 1GHz - 10 GHz
SX set
-
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Power Probes
RkP-400 Series
-
The RkP-400 Series probes consist of a compact head containing the detector and a preamplifier housed in a separate enclosure. The external dimensions of all the 400 Series Probes are the same, with identical detector planes, allowing for easy interchange of probes in an experiment. The heads have both ¼-20 and M6 tapped holes, a built-in 1” (25mm) filter holder, and a side-mounted BNC connector. Probe specific data, including spectral response curves and calibration dates, is stored in the preamplifier for access by the instruments.
-
Product
Electrical Resistance Probes
-
Electrical resistance (ER) corrosion probes are commonly used in petroleum, chemical processing, and other environments where on-line corrosion rate readings are required. Whereas test coupons must be removed from the process for evaluation, corrosion probes can allow corrosion rate determination without probe removal.
-
Product
Current Probes
-
Innovative DC to 5MHz "positional" current probe capable of measuring currents in PCB tracks, component legs etc. without the need to break the connection or surround the conductor.
-
Product
Probes with Pyranometers and SICRAM module
LP471PYRA… Series
-
The LP471PYRA… probes consist of a pyranometer LPPYRA03, LPPYRA02 or LPPYRA10 equipped with the SICRAM module and a 5m or 10m cable for the connection of the pyranometer to the instruments HD31, DO9847, HD2102.2, HD2102.1 and HD2302.0, so to get the reading in W/m² directly on the instrument’s display.
-
Product
Ingun Spring Probes
-
MicroContact AG offers the assortment of test probes and test adapters from Ingun as a Swiss representative.
-
-
Product
CP-2XX-4 Battery Probes
-
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 39Full Travel (mm): 1.00Recommended Travel (mil): 30Recommended Travel (mm): 0.75Overall Length (mil): 158Overall Length (mm): 4.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
Renishaw Scanning Probes
-
Advanced Industrial Measurement Systems
The REVO® is designed to maximize CMM throughput while maintaining high system accuracy and uses synchronized motion as well as Renscan5 measurement technology to minimize the dynamic effects of CMM motion at ultra high measurement speeds. This is achieved by letting the REVO® head do the fast demanding motion while the CMM moves in a slow linear fashion.
-
Product
Custom Probes
-
At Eddyfi, we strive to meet the most rigorous requirements. Our expertise, engineers, and manufacturing capabilities enable us to take almost any set of custom inspection requirements — dimensions, diameters, geometries, number of coil rows, topologies — and turn them into practical and high-performance solutions for you.
-
Product
Touch Probes And Vision Systems
-
HEIDENHAIN offers universal, high-accuracy touch probes for machine tools, enabling exact tool measurement, edge measurement on parts, and more. Proven technologies, such as wear-free optical sensors, collision protection, and integrated cleaning blowers, make these touch probes a dependable asset for tool and part measurement. The vision systems from HEIDENHAIN can also be conveniently deployed to monitor tools for even greater process reliability.
-
Product
Beam Probes
-
The CO2 Laser Beam Probes are hand-held plates designed to simplify the alignment of IR optical systems. They display the laser beam as a dark image on a fluorescent background using the same UV-excited, thermal-sensitive surfaces developed for Macken Instruments'' Thermal Image Plates.
-
Product
Threaded Step Probes
-
Pin position sensing - adjustable height - custom designs - anti-jump solution.
-
Product
RF/High Frequency Probes
-
Everbeing is proud to distribute GGB Industries line of PicoProbes for customers everyday RF probing needs. The popular model 40A has been serving the needs of many high frequency researchers in the sub-40 GHz range. For more information on their products, visit www.ggb.com. If a product they sell is not shown here, we are still able to acquire for you. Please contact us for more details.
-
Product
Single Ended Test Probes
-
Single ended probes ranging from 0.4mm to 1.27mm pitchWide selection of plating options to optimize contact challenges and maximize probe lifeVarious length option to provide drop-in replacement capabilityTri-temp applications – 55°C to 155°C
-
Product
Probes/Sensors
-
Fluke Calibration provides high-quality secondary platinum resistance thermometers (PRTs); industrial PRTs; high-temperature, fast-response, and other special-application PRTs; thermistor standards; secondary thermistor probes; type R and type S thermocouples. These probes may be used for temperature measuring, temperature calibration, temperature monitoring and temperature validation.
