Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
Connectors
-
We feature high performance coaxial connectors, including smp bullets. Also edge launch 2.92mm & 2.4mm connectors. & We've just started offering connectors that can be used to make cable assemblies. SMA Conectors are available for cables, and we also have sma connectors -thread in style.
-
Product
DVB-T Omnidirectional Antenna
-
The COMM-connect DVB-T Omnidirectional Antenna offers superior performance in applications requiring bandwidth in all directions. The antenna comes fully equipped with stainless steel mast brackets & 7/16 female connector, which makes it very easy to install in any type of installation. Our Antenna is housed in a very rugged radome, able to withstand very harsh weather conditions.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 50xSPST, Normally Open
42-145A-001
Relay
The 40-145A-001 (PXI) and 42-145A-001 (PXIe) 50xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
RF Detectors
-
RF detectors from Fairview Microwave are available with N Type or SMA connector series inputs and BNC or SMA connectors for outputs. Fairview RF detectors are zero bias Schottky diode and have negative video out. These zero bias Schottky diode detectors for RF have a minimum frequency between 10 MHz and 2 GHz and maximum frequency range between 2 GHz and 26.5 GHz.
-
Product
Serial Controller
PMC522/FP
Controller
The PMC522/FP provides a uniquely effective solution for integrating serial I/O requirements into a VMEbus or CompactPCI system. Implemented on a single PMC card, the PMC522/FP is fully compatible with the current generation of VMEbus and CPCI single board computers, as well as any special purpose processor that includes a PMC connector.
-
Product
PXI High Density Multiplexer, 2-Bank, 40-Channel, 2-Pole
40-615A-010
Multiplexer Module
The 40-615A-010 is a 2-bank, 40-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
50 Pin SGMC Cables - Connector to Unterminated for Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize the 50-pin SGMC connector.
-
Product
Hybrid Mixers
-
Macom Technology Solutions Holdings Inc.
MACOM’s hybrid mixers are widely used in aerospace and defense, wireless, test and measurements applications, and broadband communications applications. We offer a variety of connectorized, flat pack, drop-in, and surface mount packages with a broad range of operating frequency ranges and performance specifications. Our mixer products are available in subsets of the frequency range such as RF and LO: 50 kHz to 24 GHz and IF: DC to 8 GHz. These mixers leverage a variety of technologies such as GaAs pHEMT and Silicon HMIC and are available in double and triple balanced designs. These mixers are hermetically sealed and can also be screened all the way to space level.
-
Product
Power Supplies
CXI Series
-
The CXI-series has dual PCI-E connectors for high end graphic cards and peripheral connectors for all your other devices. The silver coated grill not only helps the air ventilation, but helps prevent future corrosion that can occur with time, which could lead to a decrease in electrical transfer.
-
Product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Tinned Ends, 1m
A009DF4-T-0A100
Cable Assembly
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation.
-
Product
4-Pin Power D-Type Cable, Male to Female, 0.5m
40-970-404-0.5m-MF
Cable Assembly
The 4-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
LXI Trigger Bus Terminator
ProDAQ 8037
-
The ProDAQ 8037 LXI trigger bus terminator connects to the ProDAQ 6100 LXI function card carrier or the 3030 PCI Express VXIbus slot-0 interface and to any LXI trigger bus wiring or daisy-chain configuration. The die-cast connector ensures a stable connection and prevents accidental disconnects.
-
Product
COM Express Type 6 Basic Module With Intel® Xeon® & 8th Gen Intel® Core™ Processors And Intel® CM246/QM370/HM370
CEM520
-
The CEM520 is a high-performance COM Express Type 6 basic module featuring triple independent displays, industrial operating temperatures and rich expansions. The CEM520 is based on the Intel® Xeon® E-2176M and 8th generation Intel® Core™ i7/i5/i3 processors (codename: Coffee Lake) with the Intel® CM246/QM370/HM370 chipset. The system-on-module is equipped with dual DDR4-2666 SO-DIMM slots for up to 32GB of system memory. Its wide operating temperature range of -40°C to +85°C strengthens the adaptability of harsh operating conditions. Integrated with Intel® Gen 9 graphics, and with the support of DX11/12, OCL 2.0 and OGL 4.3/4.4, the Intel® Xeon® and Core™-based computer-on-module presents excellent graphics performance with a resolution up to 4K. Three independent displays are supported through one LVDS, one VGA and two DDI ports for HDMI, DisplayPort. The CEM520 comes with multiple I/O connectors including four SATA-600 interfaces with RAID 0/1/5/10, one Gigabit LAN port with Intel® i219-LM controller, four USB 3.0 ports, eight USB 2.0 ports, and 4-In/Out DIO port. Also, the system-on-module is expandable with one PCIe x16 slot and eight PCIe x1 slots, as well as LPC and SMB expansion buses. Trusted Platform Module 2.0 (TPM 2.0) is supported to provide efficient hardware-based data protection. This new powerful COM Express Type 6 module is compatible with Windows® 10 and Linux operating systems. It also supports AMS.AXView – Axiomtek’s exclusive software for smart device monitoring and remote management applications.
-
Product
PXI Twelve 2:1 High Voltage Power MUX
40-331-006
Multiplexer Module
The Pickering Interfaces 40-331/332 High Voltage Power Multiplexer and Matrix Modules are suitable for applications requiring high voltage power relay switching with high density. They feature current handling up to 5A, 1000VDC/1000VDC peak cold switching and 110VDC/250VAC hot switching. The 40-331 is available as a single 24:1, dual 12:1, quad 6:1, hex 4:1, octal 3:1 or twelve 2:1 multiplexer, and the 40-332 is available in 12x2 or 6x4 matrix configurations. Connections are made via a front panel mounted 37 pin high voltage D-Type connector.
-
Product
Extension Wires And Cables
-
Omega offers thermocouple, RTD and thermistor extension wire and cable. We offer a wide variety of calibration, gauges, sheath material, insulation, connector types and shapes.
-
Product
ITA, G2, 2 Module, Removable Backshell, Keying Feature, With Protective Cover
410120110
ITA
The G2 ITA is equipped with a removable EMI-shielded cover. The cover slides up to provide access to wires and connectors and is secured by two screws. The removable and adjustable U-shaped cable clamp is attached by screws to the ITA frame and allows ITA modules to be pre-wired before assembly. The clamp can hold cable bundles with an oblong bushing effective diameter of 1.55". ITA strain relief plates are not needed.
-
Product
High Elongation Extensometers
Model 3800
-
Jinan Testing Equipment IE Corporation
The main body of this unique extensometer remains stationary during testing, held in position by the adjustable magnetic base included. Only the very light, small traveling heads move as the sample elongates during a test. These attach to the sample with small spring clips. Each head pulls a cord out from the extensometer as the head moves. These models use high precision, low friction potentiometers, and, as a result, have a wide range of factory selectable outputs. The extensometer is driven by an excitation voltage and has output proportional to the input. They can be provided with high level outputs (approximately 2-8 VDC) or ones that mimic strain gaged devices (2-4 mV/V). When set to mimic strain gaged extensometers, the Model 3800 can be used with virtually any signal conditioning electronics designed for strain gaged sensors. The potentiometers employ a hybrid wire wound around conductive plastic, which provides excellent long term stability. The output from the extensometer is readily interfaced with most existing test controllers, and may be directly input to data acquisition systems and chart recorders. Please let us know at the time of order what type of output and connector you require.
-
Product
Cable Tester, Coax Cable Mapper 8 ID Finder with Toner
TCT-128
-
A handheld testing device designed for CATV and security installers to test multi-run coaxial cable systems terminated with "F" or BNC connectors. Uses eight color coded ID finders to locate and identify cables.
-
Product
VXI Rev 4.0 Module Shield Kits
-
*One, two and three slot-wide kits for VXI Modules with 150-pin connectors. Shroudless design fits rev 4.0 chassis. All kits include side shields, a pre-machined blank front panel, ejector handles, all necessary hardware and assembly instructions. *Easy PCB layout using our CAD layout aids. All kits are available with customized front panels and side shields.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-354-HI
Programmable Resistor Module
The 40-230-354-HI (PXI) and 42-230-354-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 22.05MΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Testing Leads Assortment (16PCS)
3605A
-
Peaceful Thriving Enterprise Co Ltd
1. For use on the 6-24V circuits.2. 4mm connection for banana plugs.3. Facilities the measurement on connectors and components without destroying the insulation or the plug connection.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-124-HI
Programmable Resistor Module
The 40-230-124-HI (PXI) and 42-230-124-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 6.97kΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
-
Product
5VDC Sensor Converter, 5VDC, 15mA
ENVIROMUX-S5VDC-5V
-
External RJ45 device monitors up to two linear DC sensors, 0VDC ~ 5VDC. Output for each sensor: 5VDC, 15mA. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,956,288 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
Product
LXI Microwave Multiplexer, SP6T, 5-Bank, 50GHz, 50Ω, SMA-2.4
60-800-605
Microwave Multiplexer
Our 60-800-605 is a 5 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Filtered Analog Input Expansion Board
MSXB 048
-
The MSXB 048 Filtered Analog Input Expansion Board has a four-pole low-pass Butterworth filter on each of its 16 single-ended channels. For DAP applications that require analog filters to take out all above-Nyquist frequencies before signal conversion, it simply replaces the MSXB 037 Analog Input Expansion board. Signal inputs normally connect to the MSXB 048 through a panel-mount DB-37 connector.
-
Product
Medical Box PC Featuring The 12th/13th/14th Gen Intel® Core™ I3/i5/i7/i9 Processors, With Support For MXM GPU Module With Embedded NVIDIA RTX GPU And Thunderbolt™ 4 Port
MLB-3102 with NVIDIA MXM GPU
Industrial Computer
- ADLINK MXM graphics module support (type A/B, up to 120W TDP based on power supply)- 12th/13th/14th Gen Intel® Core™ i3/i5/i7/i9, Celeron® processor- Dual SODIMM for up to 64GB DDR5 non-ECC memory (depending on CPU)- 1x HDMI 2.0, 5x DisplayPort (1 from CPU, 4 from MXM)- 1x M.2 E-key supporting 1630 or 2230 for Wi-Fi/Bluetooth module, 1x M.2 M-key supporting 2242 or 2280 for SATA/PCIe storage module, 1x M.2 M-key supporting 2242 or 2280 for NVMe & frame grabber- Reliable Molex 24V DC-in connector- 2x 2.5GbE Intel® I225-LM Ethernet Controller- 2x PCIe Gen 3 x4 expansion slot for full-height, half-length add-on card, each slot is 25W power budget and additional Molex 4-pin power cable (12V/1.5A and 5V/2A) support
-
Product
20-Pin Scorpion Cable, Female to Unterminated, Tinned Ends, 20A, 1m
A020AFR-T-2A100
Scorpion Female Connector
This is a 1m long female to unterminated 20-Pin Scorpion cable assembly with tinned ends constructed from 19/0.41 (14AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product.
-
Product
Ethernet Connector Modules
-
With an extensive line of high-quality ethernet connector modules in our product lineup, Pulse Electronics Networking BU can easily supply the parts you need to develop your next ethernet product.
-
Product
FiberPal iOTDR
OT-9900
-
FiberPal OT-9900 iOTDR series, with power meter built-in, is designed with ultra portable, light, reliable and easy to use as Fiber Quick test and Troubleshooter to locating fiber connector, break and imperfections for PON DSN, FTTX, CATV and optical LANs. FiberPal OT-9900 iOTDR series detects event locations along the optical fiber and displays the results on a portable device like notebook, Tablet PC and Mobiles phones with Android 4.x or Windows XP/ Windows 7 operation system.
