Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 10-Bank 40GHz SMA-2.9
60-801-410
Multiplexer Module
The 60-801-410 is a 6-channel, 10-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Bi-Axial or Axial Averaging Extensometers
Model 3560
-
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parallel multiple flexure design makes these units very durable.The Model 3560AVG reads axial strain only as a single averaged output. It may also be supplied with two independent outputs, one measurement from each side of the specimen. This set-up is most commonly required when an indication of specimen bending is desired. The second version, the Model 3560BIA, includes both the averaged axial strain and the transverse strain. Again, this may also be configured as dual independent axial readings, which results in a three channel extensometer.The Model 3560 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-344-HI
Programmable Resistor Module
The 40-230-344-HI (PXI) and 42-230-344-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Copper, Type T (°C) Contact
-
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
Product
Long Travel Extensometers
-
AMETEK Sensors, Test & Calibration
We provide two long travel extensometers for materials testing; the EZ250Plus and the EX800Plus.The second type is suitable for use with rigid, semi-rigid and ductile materials. The extensometer is supplied with a universal voltage external power supply unit, a loom and a connector to fit a range of machines, as well as a mounting stand.
-
Product
EN50155 Managed PoE Ethernet Switch
EKI-9528E-12GMPW
Ethernet Switch Module
M12 connector with ruggedized IP54 certified housing, Complies with EN50155 and EN50121-3-2 standards, 24 x PoE IEEE802.3af/at ports. Wide nominal power input range: 24 ~ 110VDC, Operating power input range: 16.8 ~ 137.5VDC, X-Ring Pro delivers rapid and predictable convergence.
-
Product
Cable Assembly, 104-Pin D-Type, Female to Unterminated, Cut Ends, 2A, 0.5m
A104HFR-C-0A050
Cable Assembly
This 0.5m long female to untermiated 104-Pin D-type Cable Assembly is suited for direct connection to various products using the 104-Pin connector. It is constructed from high-flexibilty, high-specification fully screened cable and is unterminated with cut ends.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-315-014
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PMC Carrier Card
APC-PMC
-
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard PCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the PCI card slot edge connector.
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30003-J
-
Breakout board for the MAX31855J digital thermocouple interface ICs by Maxim. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 2x5 pin header (8-pins used), has four vertical mini thermocouple connectors and four mounting holes for standoffs and 4-40 screws. The SEN-30003 is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance (many other level shifters reduce data rates to below 500 kHz).
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-315-005
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI 10 Banks of 16 Channel 1 Pole MUX
40-615-022-10/16/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-415-005
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
Hand Crimp Tool For Scorpion Connector Pins
C020AFR-2CP-2A-O
Crimp Tool
Hand operated crimp tool for pins fitted into a Scorpion connector housing.
-
Product
PCI 25xDPST Reed Relay Card
50-115A-022
Reed Relay
This is the 25xDPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
3U CompactPCI 2-slot SSL 33MHz VIO 5V BW 64-Bit
80932-002-6600
-
3U CompactPCI backplane 2-slot, PICMG 2.0 R3.0, system slot left, supports full hot swap function according to PICMG 2.1 R2.0 hot-swap specification, clock frequency 33MHz, V(I/O) +5V, bus width 64-bit, power input connection with Fastons connectors
-
Product
PXI/PXIe Microwave Relay, Quad SPDT, 2.5 GHz, 75 Ω, 1.6/5.6, Failsafe
42-780B-754
Relay
The 40-780B-754 (PXI) and 42-780B-754 (PXIe) are quad failsafe SPDT 2.5 GHz 75 Ω unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
160 Pin DIN 41612 Connectors for Pickering Products
-
The connectors below are suitable to use with Pickering cards and modules that utilize a standard voltage 160-pin DIN 41612 connector.
-
Product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781397-01
Voltage Input Module
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
Product
High Voltage 9-Pin D-Type Connector & Cable Accessories
-
The High Voltage 9-Pin D-Type connector is used on high voltage PXI and LXI switching products to provide a high voltageconnector solution. Connection solutions for modules with Standard Voltage Rating D-Type connectors are also available.
-
Product
2-port/4-port PCI Express 1GigE PoE Card with M12 X-
AX92325
-
Four M12 x-coded connectors with special design (to avoid occupying two slots) 2 or 4 independent Gigabit PoE ports, Supports 9.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 30W at 54 VDC per port, PCI Express x4 compliant
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 12-Bank 40GHz SMA-2.9
60-801-412
Microwave Multiplexer
The 60-801-412 is a 6-channel, 12-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
General Purpose Quartz Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
Product
50 Pin IDC Connector Breakouts
-
The connector breakouts below are suitable to use with Pickering cabling products that utilize a 50-pin IDC connector.
-
Product
Interposers and Probes
Interposer
The Summit product family includes a wide variety of Interposer systems, designed to reliably capture serial data traffic while minimizing perturbations in the serial data stream. Probes include interposers, which are designed to capture data traffic crossing the PCI Express card connector interface, and MidBus probes, which are designed to capture traffic flowing within a PCB.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 2m, Exit Towards Pin 1
A050DM5-050DM5-0A200
Cable Assembly
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
40-972-025-0.5m-MU
Cable Assembly
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Low Pass and Bandpass SMA Coaxial Filters
-
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
Product
26-Pin D-Type Connector, Male
40-960-026-M
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections.
-
Product
PXI/PXIe Power Relay Module, 18xSPST, 5 Amp, 37-pin D-type Connector
42-153-104
Relay
The 40/42-153-104 is a PXI/PXIe high density power relay module with 18xSPST switches rated at 5A. User connection is via a 37-pin D-type male connector.
