Control
Known value
-
Product
Engine Test Systems
Dynas3
-
Dynas3 Machines are specially suited for use in engine test stands. The AC machine, variable frequency drive with test stand controller and safety module are tuned to one another to form a system that has proven itself many times over. It can be used in any type of development and function test stand. The applications range from simple test stands for steady state operation up to sophisticated test stands for dynamic test cycles. Nearly every application in the field of engine testing can be performed on a test stand with DYNAS3.
-
Product
Transimpedance Amplifiers
-
Advanced Science and Novel Technology, Co., Inc.
Broadband transimpedance amplifier for low noise receiver side applicationsFeatures automatic input offset control and a peak detector8GHz of analog bandwidth for limiting of input data60dB of transimpedance differential gain15pA/sqrtHz of input referred noise density (0.1 to 10GHz)CML output interface with 50 termination and 225mVp-p single-ended swingSingle +3.3V power supplyPower consumption: 250mWExhibits low jitter and limited temperature variation over industrial temperature rangeUnpackaged bare die
-
Product
Engine Performance/Endurance Test System
-
Various types of test system as follows can be built up in combination with measurement control equipment and peripheral instruments (fuel flow meters, actuators, temperature control device, combustion analysis system, ECU monitor, OBD, sound and vibration measurement instruments, emission analyzer, smoke meter etc.)·Traveling fuel economy test·Gas emission test·Output performance test·Deterioration/endurance test·Combustion analysis·Sound source probing
-
Product
2.92mm to ProBus Probe Adapter
L2.92A-PBUS
-
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PBUS adapter converts the 2.92mm interface to a ProBus interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi from high-impedance ZS active probes to the high-bandwidth WaveLink differential probing system. Full probe power and control is provided through a built-in LEMO interface.
-
Product
Power Interface and Prototype PXI Card
GX7404
-
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
Product
Software
S!MPATI®
-
You reach all important functions quickly and easily via the clearly structured S!MPATI® menu with intuitive operation. In addition, a floor plan of your laboratory can be uploaded and the layout of all testing systems visualised for optimal handling. This means, you can control and program all test cabinets conveniently from one computer as well as evaluating their data. This effectively increases the efficiency of your systems and also provides protection against downtime.
-
Product
10MHz DDS Sine & Square Wave SIGNAL GENERATOR
SG-10
-
Model SG-10 architecture is based on the latest advances in DDS technology. Microprocessor control delivers clean and accurate DC to 10MHz waveforms with frequency accuracy of 0.02% and 0.1 Hz frequency resolution.
-
Product
Intelligent Application and Service monitoring
Datadog
-
With turn-key integrations, Datadog seamlessly aggregates metrics and events across the full devops stack.*SaaS and Cloud providers*Automation tools*Monitoring and instrumentation*Source control and bug tracking*Databases and common server components*All listed integrations are supported by Datadog
-
Product
Osprey PCI Unibus Adapter
9793
-
Dual-height card plugs into PDP-11 Unibus backplane. Fibrechannel cable plugs into Unibus logic connector on Osprey /TXP I/O Adapter logic provides Programmed I/O and DMA access to "real" Unibus compatible controllers (those not otherwise emulated).
-
Product
GPIB-RS232, Instrument Control Device - Japan 100VAC
779732-07
-
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Smart Power Stage
-
Renesas Smart Power Stage (SPS) modules have integrated high accuracy current and temperature monitors that can be fed back to the controller and doubler to complete a multiphase DC/DC system. They simplify design and increase performance by eliminating the DCR sensing network and associated thermal compensation.
-
Product
Calibration & Repair Services for Instruments in Process Control
-
Meeting customer needs is our number one priority. Hastings Instruments offers free technical support as well as personalized one-on-one customer service through a diverse organization of field Customer Service Representatives and Distributors. We have more than 50 field Customer Service Representatives that are situated to provide local support throughout the world.Additionally, reaching our Customer Service Department is only a toll-free number away (USA) and is available for your convenience. Faxing or E-mailing your question first will assure that it is reviewed before you speak to a Customer Service Representative. Also, following the steps listed in our trouble shooting guides (included in each product instruction manual) may help direct you to the appropriate department before you pick up the phone to call.
-
Product
Cell Stand
CS-3A
-
The CS-3A Cell Stand is adopted with CHI series Electrochemical Analyzers and other apparatus directly. The cell is enclosed in a Faraday cage to reduce electrical interference. A built-in gas control allows purging a sample. Gas line is provided to purge next sample, while analyzing the present sample separately, thus increasing productivity. Magnetic stirrer allows for controlling the mixing of the sample for experiments requiring mass transport of electrolyte or analyte to the electrode surface. Cell top positioner with detachable cell cap allows easy removal and replacement of the cell vial as well as the electrodes for rinsing, cleaning, and replacement.
-
Product
Signal Conditioners & Measuring Transducers
-
Signal conditioners and measuring transducers ensure interference-free signal transmission in measurement and control technology. From highly compact 6 mm signal conditioners and measuring transducers through signal conditioners with functional safety to signal isolators for intrinsically safe circuits in the Ex area: our signal conditioners and measuring transducers ensure interference-free signal transmission in MCR technology.
-
Product
Syringe Pumps
SyriXus Series
-
Teledyne LABS SyriXus® single-pump syringe pumps feature exceptional quality, precision and durability. They consist of a precise controller and syringe pump module for the all-important accuracy you demand. The piston-driven module uses a single speed gear train.The SyriXus controller offers many different operating modes and features, including high-pressure syringe pumps. We can also customize the software to your specific application upon request.
-
Product
PWM Servo Motor Drives
-
NAI's PWM Servo Motor Drives provide programmable, PWM output drive (up to 65 V @ 10 A continuous) from a single +28 VDC input source and Drives Brushed or Brushless (BLDC) motors. Available in 3U OpenVPX and VME board constructions and specifically designed for rugged defense, industrial, and commercial applications with a -40°C to +85°C operating temperature range, these PWM Servo Motor Drives deliver a COTS solution for embedded motor control applications.
-
Product
Digital Step Phase Shifter
-
RF Lambda’s digital step phase shifters are designed to actively change the phase of an RF signal using digital TTL control signals. They are available in a variety of frequencies, phase shift ranges, and step sizes. Hermetically sealed options are available upon request.
-
Product
AC/DC Clamp Milliammeter (CE)
M-700
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High sensitive for low range leakage current.*Suitable for measurement of 4-20mA DC controlled circuit.*DC mV analog signal output.*Lowest influence from Magnetization and Terrestrial magnetism.*Wide measuring ranges up to DC 1000mA and AC 10A.
-
Product
Pulsed Transmitter
-
Built to operate in harsh environments, the Pulsed Transmitter unit provides radar installation decoy protection in a compact footprint and is powered by a Dewey Generator.The unit is comprised of a power supply, power amplifier, signal generator and antenna, with a fiber optic command and control interface providing throughput speeds capable of 1.25 G bits/sec via 1310 nm, single mode, ruggedized fiber.
-
Product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787457-01
-
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
Product
Digital H.V. Insulation Tester(15kV)
7016 IN
-
Standard Electric Works Co., Ltd
● Protection class: IP66 (Lid closed)● Test insulation resistance up to 30TΩ (30000GΩ).● Short-circuit current up to 5mA● Microprocessor controlled.● 30 insulation test voltages : 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV, 10.5kV, 11kV, 11.5kV, 12kV, 12.5kV, 13kV, 13.5kV, 14kV, 14.5kV, 15kV● AC/DC voltmeter (600V).● PI (Polarization Index) indication.● DAR (Dielectric Absorption ratio) indication.● Auto-ranging on all insulation ranges.● Backlight function.● Menu driven.● Visual and audible warning if external voltage is present. (≥30Vac or ≥30Vdc)● Auto-hold function to freeze the reading.● Overload protection.● Adjustment for testing time (duration) : 1~30 minutes● Auto-off.● Calendar.● Optical USB to RS-232 data transmission.● 200 measurement results can be saved in the memory and recalled on the display.● Safety standard : EN 61010-1 CAT IV 600V EN 61010-2-030 EN 61326-1
-
Product
CompactRIO Embedded Real-Time Controllers
-
CompactRIO embedded real-time controllers provide deterministic offline execution of LabVIEW applications. A wide range of controllers are presented, differing in performance and operating conditions.
-
Product
GPIB PCI Mezzanine Card (PMC) Interface & Cable
GPIB-PMC-XL
-
The GPIB-PMC-XL is a PCI Mezzanine Card (PMC) GPIB controller card that converts any CPU card with PMC slots into a GPIB controller.It performs all the basic IEEE-488.1 functions such as talker, listener and system controller. The IEEE-488.2 compatible functions make it fully compliant with the IEEE-488.2 specification. In controller applications, you can control typically up to 15 devices (instruments). If operated as a talker/listener (device) interface it does exchange data and state information with the current controller-in-charge of the GPIB bus. The GPIB-PMC-XL lets Windows and Linux programs control GPIB devices.The flat ribbon cable has a standard GPIB jack on one end and a receptacle to be plugged into the GPIB card on the other end. The 30cm (12in) flat ribbon cable is included by Team Solutions, Inc.
-
Product
FAYb Laser Markers
LP-RF Series
-
Panasonic Industrial Devices Sales Company of America
The LP-RF200P Series FAYb Laser Marker features:- Compact IP64 Rated Head- Controller Offers High Resistance To Electrical Noise- Smart Functions To Adapt To Many Conditions- Direct Link To Image Processing Device- 17-Watt Fiber Laser- Removable Fiber Cable For Easy Installation
-
Product
Modular UPS
PM SERIES 10 - 2080 kVA
-
PM Series is a scalable, redundant Modular UPS system designed to cost effectively provide high level availability for high density data centers and critical applications. True Online Double Conversion and advanced DSP control technology. Modular Architecture can scale power and runtime as demand grows or as higher levels of availability required. Combines the modular design with the N+X parallel redundancy technology.The maximum capacity of a single cabinet is 520kVA. Cabinets can operate in parallel configuration to build a system of up to 2080kVA.
-
Product
MIMO Vibration Controller
Spider-80M
-
The Spider-80M platform is based on the efficient Spider-80Xi architecture and is dedicated to MIMO VCS control and MIMO structural testing applications. Each Spider-80M chassis features 8 outputs capable of carrying out 6-degree of freedom MIMO testing. One Spider-80M chassis and multiple Spider-80Xi chassis can chain together to form a very large system with up to 504 input channels.
-
Product
Click Wrenches
-
For good torque control at a great price, equip your shop with Mountz click wrenches. Strong, durable, and reliable, our click wrenches deliver the power you need to tighten any bolt. Your user will know when they've reached the sweet spot when they hear the audible click. This enhances process control and product quality by helping to prevent over- or under-torqued bolts.
-
Product
USB-6361, 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
782254-01
-
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Power Supply
-
High precision analog control loop power supplies for inductive loads such as electromagnets, superconducting coils, Helmholtz coils and others.Autonomous analog power supplies with digital controls, readouts and supervision. The interfaces are digital and analog
-
Product
PCI Daughter Boards
DB-24PR/24 (24V Power Relay Board)
-
The DB-24R consists of 24 form C, electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 0.5 A /110 V load or 1A / 24VDC. The relay is energized by applying a 5 voltage signal to the appropriate relay channel on the 50-pin Opto-22 compatible connector or D-Sub 37 connector . Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated . This board needs a +12VDC or +24VDC external power supply to avoid overloading your PC’s power supply.
