Modbus
communications protocol for sharing data between controllers.
See Also: Communication Protocol, Near Field Communications, Data Communications, Modbus RTU
-
Product
Analog I/O Modules
-
Remote RS-485 I/O modules using Modbus RTU protocol offer complete analog I/O for current, voltage, thermocouple or RTD.
-
Product
Gas Monitors with X3® Technology
Ultima® X
-
The Ultima X Series Gas Monitors with X3 Technology bring the power of multi-sensing, signal boost and ModBus output to the Ultima X line of MSA gas monitors. The units are crafted from either stainless steel or NEMA 4X-rated plastic, and our patented SafeSwap sensor disconnect-underpower feature allows all sensors to be replaced in hazardous areas without area declassification.
-
Product
Fieldbus Gateway
EKI-1242IEIMS
-
Modbus RTU/TCP to 3-in-1 EtherNet/IP or PROFINET or OPC UA Protocol Gateway, Wide Temperature. Seamless integrate Modbus RTU/TCP and EtherNet/IP or PROFINET or OPC UA communication. Built-in real time diagnostic to increase high efficiency of device management.
-
Product
16DI Modbus RS-485 Remote I/O
ADAM-4051
-
16ch digital inputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system2500VDC isolation protection
-
Product
Fixed Gas Detectors
700 Series
-
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
Product
Digital Panel Meter
CM3-VA9
-
CM3-VA9 is a multifunctional 3-phase voltage/ current meter.With 3 phase voltage or current display at the same, configurable display range via front buttons, anti-inference design, reliable quality and easy to use and install, CM3-VA9 also has multiple I/O functions including 6relay outputs, 3 analogue output and a RS485 communication port running the Modbus RTU Protocol
-
Product
5 Digit Frequency Meter
CS2-F
-
CS2-F Freqeuncy Meter is designed high accuracy measurement, display, control and communication (Modbus RTU mode) of pulse(Frequency) or AC Frequency.● The innovation feature is auto-range input from 0.01Hz~ 100KHz(~140KHz in option). The display resolution will be auto-changed to show the highest according to input frequency. They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of testing and machinery control applications. Please refer to the detail description on pages 2/33~7/33.There are not only controllers, but also an I/O interface in any system. ADtek built in difference ideal for External Control input and Relay output as like as I/O module of PLC. It’s very connivance to achieve remote monitoring and control by CS2 series.
-
Product
Pyranometer products
-
Hukseflux Thermal Sensors B.V.
Hukseflux is a leading manufacturer, both in technology and market share, of pyranometers, pyrheliometers, pyrgeometers, net radiometers and albedometers.We produce a complete range of solar and longwave radiation sensors, compliant with the latest ISO, IEC and WMO standards. Each Hukseflux pyranometer is classified as ISO 9060 secondary standard, first class, or second class, and offers the best measurement accuracy in its class. Pyranometer output is analogue and/or digital (Modbus over RS-485/TTL).
-
Product
Handheld Serial Data Analyser
SDA-02
-
Non-intrusively displays, captures and analyses electrical asynchronous data. Directly accepts RS232, RS485/422 and CMOS/TTL signal levels. Modbus over Serial Line protocol capability (RTU & ASCII), automatically checks & generates CRC/LRC, can act as master or slave.
-
Product
Electromagnetic Water Meter
WATERFLUX 3070
-
WATERFLUX 3070 is the first battery powered water meter for the drinking water industry that is capable of measuring flow, pressure and temperature with one sensor. Communication via Modbus RTU or pulse.
-
Product
Analyzers
-
for analysis and optimizing of all RS232 and RS422/485 field-bus connections. It gathers exact information about every line change with 1µsec precision – indispensable for each analysis of time depending protocols like Modbus RTU, Profibus or similiar.
-
Product
Open Master/Slave Application Protoco
Modbus TCP
-
Modbus-TCP means that the Modbus protocol is used on top of Ethernet-TCP/IP. Modbus-TCP is an open Industrial Ethernet network which has been specified by the Modbus-IDA User Organization in co-operation with the Internet Engeneering Task Force (IETF) as an RFC Internet standard.
-
Product
8-Slot Distributed DA&C System For RS-485
ADAM-5000E
-
RS-485 communication for easy installation and networking8 slots for up to 128 points data monitoring card control in one moduleSupports ADAM ASCII protocol or Modbus®/RTU protocolSupports Modbus/RTU protocol with user-defined Modbus addressExtensive software support, includes windows DLL drivers, OCX drivers, OPC server and popular HMI/SCADA software driversSeamlessly integrated with easy-to-use ADAMView data acquisition software
-
Product
8DI/8DO RS-485 Remote I/O
ADAM-4050
-
8ch digital input/8ch digital outputProtocols: Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
Modbus TCP Data Acquisition
-
Modbus TCP based Data Acquisition Modules in a analog and digital I/O configurations including current, voltage, thermistor, thermocouple, RTD, and strain gauge. Some are powered over Ethernet, some have two Ethernet ports and some can send email alarms and trigger outputs based on inputs.
-
Product
Multifunctional Meter
CPM-20
-
CPM-20 multifunction power meter provide high accuracy single phase and three-phase measuring and displaying, energy accumulating, power quality analysis, and data communication.It provides maximum/minimum records for power usage and power demand parameters.Hardware standard built in a RS485 Modbus communication port.FCC and CE Approved
-
Product
12DO(Source Type) Modbus RS-485 Remote I/O
ADAM-4056SO
-
12ch source type digital outputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system5000VDC isolation protection
-
Product
Industrial Ethernet
-
PLANET Industrial Ethernet equipment is compliant with various industrial protocols and ITS certifications such as MQTT, Modbus, SCADA, EtherCAT EN50155 and E-Mark to meet all the transmission needs, be it Information, Control or Device. PLANET features ERPS Ring, IEEE 1588 PTP, Layer 3 routing, 10G transmissions, cybersecurity and more to ensure high performance and security of our comprehensive Industrial Ethernet collection.
-
Product
4 2/3 Digit Voltage/Current Meter
CS1-VA
-
CS1-VA economic type Voltage/Current Meter is designed with high accuracy measurement, display and communication of 0~600V or 0~10A for DC/AC/TMRS.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of industrial and testing applications.
-
Product
Temperature and Process Controllers
-
The ATR121 Temperature Controller is a 3 digit display PID controller with up to 2 relay outputs, Solid State Output and an option to be a Modbus RS485 Slave device.The ATR141 Temperature Controller is a 4 digit PID controller and Panel Meter which can display up to 3200°F with an S Type Thermocouple. The ATR141 can have up to 2 relays, a Solid State Output and an option to have a Modbus RS485 output.
-
Product
OPC UA Ethernet I/O Modules
ADAM-6300
-
Industrial OPC UA Ethernet I/O Modules with Modbus protocol converge OT/IT with security, linking to SCADA and the cloud for remote monitoring.
-
Product
5 Digit Programmable Speed/Velocity Meter
CM1-RL
-
CM1-RL series provides a simple economic programmable speed/velocity table, it 20.0mm, 5-digit LED display, press the key to set the display range and its anti-jamming design and reliable quality, simple installation, you can meet the needs of general measurement of speed/velocity.This instrument also has 2 group relay outputs, 1 analog output, or 1 groups RS485 (Modbus RTU mode) communication features three a (More features please refer to page description). Operation press the inner design, the more human-no action can be avoided, especially suitable for all kinds of machinery used.
-
Product
OPC Server
-
An OPC sever (OLE for Process Control) provides IO and more devices to communicate with a wide range of HMI/SCADA software packages residing on a host. Advantech''s OPC server for ADAM and modbus devices features OPC DA (data access) and AE(alarm and events) client for the rapid testing.
-
Product
Flow Monitor
B2900
-
Blancett B2900 flow monitor offers advanced digital signal processing technology in an easy-to-access package. Enclosed in a spacious polycarbonate NEMA 4X housing, the electronics are located on a single board, designed for straightforward and convenient field installation. The B2900 enclosure features an LCD display with push button programming as well as a pre-drilled hole for external wiring connections, such as Modbus RTU and other outputs.
-
Product
Seismic Alarm Recorders
-
ICP DAS USA brings the advanced Seismic Alarm Recorder for earthquake detection. It communicates over Modbus RTU and Modbus TCP protocols and can be used to establish an quake warning system and prevent further damages. Our Seismic Alarm Recorders can be used with our FREE EZ Data Logger Software and other SCADA software for data logging, monitoring and analysis. It can be used in museums, residential and commercial buildings, and research institutes to monitor earthquakes.
-
Product
Multifunctional Meter
CPM-80
-
CPM-80 multifunction power analyzer provide high accuracy single phase and three-phase energy measuring and displaying, energy accumulating, power quality analysis, data logging and data communication. CPM-80 series meters are able to measure bidirectional, four quadrants kWh and kVarh. It provides maximum/minimum records for power usage and power demand parameters. Hardware standard built in a RS485 Modbus communication port , 4 Digital inputs, 2 Relay outputs, LCM and 2MB flash for data-logging. In addition , also provide TOU , voltage and current THD, harmonics up to the 63rd and auto wiring change via software .
-
Product
WISE Data Acquisition Controllers
-
WISE (Web Inside, Smart Engine) are Modbus TCP based data acquisition controllers that allow for remote monitoring and logic control through a web interface. They can trigger outputs based on inputs, send email alarms and can show the status through a web page.
-
Product
RTD Temperature Indicator
CM2-TR
-
CM2-TR RTD Temperature Indicator has been designed in simple operation and 4 digital 20mm LED display with economic cost.They are can be programmed by buttons that are hidden in front panel.They are also available to option relay output and an analog output or RS485 (Modbus RTU Mode) communication.
-
Product
Modbus I/O Expansion Racks
-
Modbus is a protocol in the industrial manufacturing and environment monitoring fields. It suits master-slave or query-response distributed I/O applications. The units have pre-installed a Modbus firmware. PC's, HMI's or PLC's can use Modbus/TCP and Modbus/RTU protocol to communicate with I/O modules in the unit via the RS-232/485 or Ethernet interface.
-
Product
Digital Panel Meter
VAM
-
VAM Voltage & Current Meter has been designed with high accuracy dual channels(isolated) measurement, dual display and communication of 0~600V and 0~10A for DC/AC/TMRS. In compact size(48 x 96mm)● Build in mathematic function such as Addition / Subtraction / Multiplication / Division / high or low selector in 2 channels input to meet various testing equipment inquiry.They are also build in 4 Relay outputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.
