Modbus
communications protocol for sharing data between controllers.
See Also: Communication Protocol, Near Field Communications, Data Communications, Modbus RTU
-
Product
4AO/4DI Modbus RS-485 Remote I/O
ADAM-4024
Ethernet I/O Module
4ch analog output/4ch digital inputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system3000VDC isolation protection
-
Product
16-Port +2 SFP Entry-Level Switch Supporting Modbus TCP/IP
EKI-5726FI-MB
Ethernet Switch Module
Entry-Level Managed Switch, Provides wide operating voltage 8.4~52.8 VDC, C1D2 and ATEX certified for horizontal area. IXM function enables fast deployment, Modbus/TCP Enabled by default, Supports X-Ring for ultra high-speed recovery time less than 20ms.
-
Product
Modbus Module Test Tool Software
ModTest
-
Modtest 2 software allows the configuration and settings of a Rotork Modbus Module Mk2 inside an individual actuator to be carried out easily and simply over the data bus. In addition, the actuator can also be exercised using this PC based software. The Modtest 2 software is used for diagnostic and maintenance of a Modbus controlled actuator over a serial link from the PC.
-
Product
Gas & Flame Detection System
Syntel
-
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
Product
Monitors
-
Whether you need a local display, alarm and shutdown capability, data recording, and the ability to communicate using Modbus over Ethernet TCP/IP; or you need to trend waveform and transient data to provide a predictive look at your machine’s condition, Metrix has a solution to meet your machinery monitoring requirements.
-
Product
Modbus Register Converter
Model 2390
-
* Converts Modbus Registers and variables for replacement Modbus devices.* Maintain existing software when upgrading Modbus systems.* Provides serial control of Modbus RTU devices from any ASCII source.* User defined Register Conversion Table supports all Modbus RTU devices.* Internal Register Conversion Tables for Watlow F4-to-EZ-ZONE and F4-to-F4T conversion.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes baud rate conversion capability.* Uses SCPI commands to load the Conversion Table and set serial settings.* Small metal case mounts on a DIN rail or on any flat panel.* 239x Table Loader Program uploads the 2390 Register Conversion Table from an Excel csv file.* 239x Serial Keyboard Program provides instant control of the 2390 and Modbus Slave Devices without writing a program.
-
Product
Fixed Gas Detectors
700 Series
-
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
Product
Process Indicator
CS2-PR
-
CS2-PR Process Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~10V and 4(0) ~20mA with square root function.They are also build in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.
-
Product
Multifunctional Meter
CPM-70
-
CPM-70 multifunction power analyzer provide high accuracy single phase and three-phase energy measuring and displaying, energy accumulating, power quality analysis, data logging and data communication.CPM-70 series meters are able to measure bidirectional, four quadrants kWh and kVarh.It provides maximum/minimum records for power usage and power demand parameters. Hardware standard built in a RS485 Modbus communication port , 4 Digital inputs, 2 Relay outputs, LCM and 2 MB flash for data-logging.
-
Product
10 Digit Rate/Batch Counter (Analogue)
CS2-TM-Analogue
-
The CS2-TM Totalizer controller provide high accuracy measurement, display, control and communication (Modbus RTU mode) of 0~10V/4~20mA from flow meter or mV from Shunt for Amp-Hour.There are two display screen and 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue, 1 Pulse and RS485 port available. They are also support fantastic control function as like as N, R, C mode for totalizer and batch control.
-
Product
4AO/4DI Modbus RTU Remote I/O
ND-6124
Data Acquisition Module
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
Product
6 Digits Process Meter
A6-PR
-
A6-PR 6 Digits Process Meter has been designed with high accuracy measurement, 6 digit display, flexible I/O functions and communication port for process measuring application.There are also build in 4x External Control Inputs, and can option 4x Relay outputs, 1x Analog output and 1x RS485 (Modbus RTU Mode) communication port with multi-functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.There was designed the zero tracking and stable tracking function in programming level.According to the application, user can set the function to get the suitable reading.
-
Product
Modbus Controllers
-
Datexel has a range of Modbus RTU Masters, Slaves, Controllers, Data Loggers and Modbus remote displays. The DAT9000 is a Modbus RTU Master with RS485, RS232 and Ethernet Interfaces. The DAT9000IO is similar to the DAT9000 but it has digital input and outputs. The DAT9000DL has an additional Data Logging facility and the DAT9000DLIO has both Data Logging and digital IO. The DAT9011 is a Modbus Master with 2 analog inputs which can chose from Thermocouple's, RTD's, Potentiometers, mA and mV's. It also has 2 outputs which can be mA or voltage. The DAT9011 can also accept digital inputs and provide 2 SPDT relay outputs. The DAT9011DL also has a Data Logging facility which can store up to 8gb of readings on a thumb drive.
-
Product
12DO(Source Type) Modbus RS-485 Remote I/O
ADAM-4056SO
Remote Interface Unit
12ch source type digital outputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system5000VDC isolation protection
-
Product
Industrial Ethernet
-
PLANET Industrial Ethernet equipment is compliant with various industrial protocols and ITS certifications such as MQTT, Modbus, SCADA, EtherCAT EN50155 and E-Mark to meet all the transmission needs, be it Information, Control or Device. PLANET features ERPS Ring, IEEE 1588 PTP, Layer 3 routing, 10G transmissions, cybersecurity and more to ensure high performance and security of our comprehensive Industrial Ethernet collection.
-
Product
4 2/3 Digital Resistance Meter (1/32 DIN)
CS3-RS
-
CS3-RS Resistance Indicator has been designed with high accuracy, display, control, remote communication.A compact body design for small equipment, laboratory instrument, and others.Also are available with relay output, analog output, RS485 Modbus RTU communication to cover a wide range of applications.
-
Product
Oxygen Analyzer
DT3000
-
The Datatest Model DT3000 is a Zirconia sensor, microprocessor based, oxygen analyzer. The DT3000 comes with probe configurations for temperatures up to 3200F. The microprocessor based controller provides long-term stability and reliability, plus optional features for controlling back purge, calibration gas injection, and self-calibration. 4 - 20 mA output and Modbus RTU serial port are standard. The DT3000 is available in either a NEMA 4 wall mount or panel mount configuration.
-
Product
4 2/3 Strain Gage Meter
CS2-SG
-
CS2-SG Strain Gauge Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV as like as Load Cell or Strain Gauge.The meter supports Field Calibration function. It can be calibrated with sensor(Load Cell/Strain Gauge) to meet machinery structure.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS-485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of machinery and testing equipments applications.
-
Product
High performance, USB, Ethernet, WiFi
T7 Series
-
USB, Ethernet, or 802.11b/g WiFi connectivityFully compatible with Modbus TCP/UDP14 analog inputs at 16–18+ bit resolutionT7-Pro: up to 22 bit resolution, and WiFi2 analog outputs23 digital I/O
-
Product
Analog I/O Modules
-
Remote RS-485 I/O modules using Modbus RTU protocol offer complete analog I/O for current, voltage, thermocouple or RTD.
-
Product
Multi-Function Power Transducer
TD2418B
-
The TD2418B is a micro-process based transducer with a 16 bits CPU (Center process unit) and equipped with full-digitized measuring, calibrating and output functions.TD2418B not only can take the place of several static con-verters and measuring instruments (V, A, W, PF, VAR, WH, VARH, Hz) by single unit, but also have some special function such as Maximum measuring, Minimum measuring and comparator output. In communication, we use the most convenient and the easiest RS232 or RS485 as our standard output port, besides, we adopt Modbus Protocol, one of the most popular protocol in the world, as our standard protocol.
-
Product
Modbus RTU Analog Input Modules
-
The Datexel range of Modbus RTU analog input cards for both RS485 and RS232 with Modbus or ASCII protocol can be combined with the DAT9000 series of Modbus Masters. A choice of input cards or modules are available and have various optional inputs such as Voltage, Current, Thermocouples, RTD, and Resistance. Also a choice of 2, 4, 8 channel options are available. The DAT3011 is a Modbus RTU Slave with 1 selectable universal input (Thermocouples, RTD, mV, RTD's or Resistance), 2 x 4-20mA or 0-10V input and 2 x4-20mA outputs. The DAT3011 also has 3 digital inputs and 3 relay outputs. Each module is isolated from each other and is set up using the DAT3000 software Development package which is free of charge from the Datexel download web page. Datexel also has universal input modules. An 8 channel analog input card is available making the DAT3000 series a very economical solution to large and small scale Data Acquisition. Combining these analog input cards with the analog output cards, the digital input/output cards and the communication devices make Datexel the smart choice where Data Acquisition is required.
-
Product
Smart Meters
EVA-P200 Series
-
EVA-P series are compact, cost-effective power meters with high accuracy, Modbus RTU, and flexible wiring—ideal for monitoring and maintenance.
-
Product
RS-485 Serial I/O
ADAM-4000/4100 Series
-
The ADAM-4000/ 4100 series featuring rugged industrial-grade cases are specially designed for reliable operation in harsh environments. Built-in microprocessors independently provide intelligent signal conditioning, analog I/O, digital I/O, data display, and RS-485 communication through Modbus RTU protocols.
-
Product
Fieldbus Gateway
EKI-1242IEIMS
-
Modbus RTU/TCP to 3-in-1 EtherNet/IP or PROFINET or OPC UA Protocol Gateway, Wide Temperature. Seamless integrate Modbus RTU/TCP and EtherNet/IP or PROFINET or OPC UA communication. Built-in real time diagnostic to increase high efficiency of device management.
-
Product
Free Serial-TCP (More Than Just A Device Server)
-
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and speed. The Serial-TCP program (more than just a Device Server) bridges your existing Serial COM port and TCP/IP without the need for changing existing protocol. It works seamlessly and transparently, just like passive RS232 / RS485 / RS422 converters, repeaters, and hubs, while the difference is that one requires installation of cables and converters with limited distance; and the other simply makes use of the existing computers and networks with an unlimited transmission distance
-
Product
Multifunctional Meter
CPM-12
-
CPM-12 multifunction power meter provide high accuracy single phase and three-phase measuring and displaying, energy accumulating, power quality analysis, and data communication.Hardware can be option a a RS485 Modbus communication port.Auto wiring change (Note) via softwareCE and FCC approved
-
Product
Free Serial Port Tools
-
*The clever terminal program for serial port and field-bus communication.*Build your own sending dialogs and create customized user interfaces *Simulate field-bus telegrams *Play Modbus ASCII/RTU master with predefined Modbus function dialogs
-
Product
16DI RS-485 Remote I/O
ADAM-4053
Remote Interface Unit
16ch digital inputProtocols: Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
5 Digit Frequency Meter
CM1-F
-
CM1-F is an economical and simple frequency meter with a 20mm 5-digit LED display, and the display rangecan be set by pressing the button. Anti-interference design, reliable quality, simple installation and operation.At the same time, it has 2 sets of relay output or 1 set of analog output or 1 set of RS485 (Modbus RTU mode) communication ports for selection.The built-in design of the operation buttons can avoid human misoperation and is suitable for various mechanical use.
