Product

5 Slot VME64x Portable Tower Development Platform; Type 32 Tower Chassis

32V05OP146N3VGBX

-

ELMA Electronic, Inc.

32V05OP146N3VGBX - ELMA Electronic, Inc.

Elma Type 32V family of enclosures provide a lightweight, tower platform for packaging portable VITA System applications. Designed to VITA & IEEE . Systems can be configured with or without rear I/O card cage.

Product

Type 12R2, 9U, 19" Rackmount, MIL-Rugged, Vertical

12R2-9U-V

-

ELMA Electronic, Inc.

12R2-9U-V - ELMA Electronic, Inc.

The 9U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.

Product

Type 12R2, 19" Rackmount, MIL-Rugged, Family

12R2

-

ELMA Electronic, Inc.

12R2 - ELMA Electronic, Inc.

The 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.

Product

VXS Type 32V, w/plug in PSU

32V05LY348Y3VGE0

-

ELMA Electronic, Inc.

32V05LY348Y3VGE0 - ELMA Electronic, Inc.

VXS Type 32V family of enclosures provide a lightweight, tower platform for packaging portable VITA System applications. Designed to VITA & IEEE. Systems can be configured with or without rear I/O card cage.

Product

Low Voltage DC / Battery Powered High Voltage Amplifiers

WMA-005 And WMA-005LF

-

Falco Systems

WMA-005 And WMA-005LF - Falco Systems

The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.

Product

Type 39 CompacFrame Development Platform, 1 - 4 Slot 3U VPX Power And Ground Backplane

39P01BWX6ZY2VCC0-Tx

-

ELMA Electronic, Inc.

39P01BWX6ZY2VCC0-Tx - ELMA Electronic, Inc.

Elma’s slimline CompacFrame is the next-generation platform designed to accelerate development and test of Plug-In Cards (PICs). The 3U card cage in the platform is tilted upward by 5º for easier card access and accommodates backplanes up to 4 slots.

Product

Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Vertical

12R2-8U-V

-

ELMA Electronic, Inc.

12R2-8U-V - ELMA Electronic, Inc.

The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.

Product

Transceiver Driver

S-112

-

Notice

S-112 - Notice

Transceiver Driver slot module of FOTS system is an efficient module for the characterization of SFP type transceiver and the test of optical line or components. This module is a kind of Small Form Factor Pluggable(SFP) host board that can be used to test SFP transceiver modules to define the modules’ performance. The transceiver driver slot has two SFP cage and 20-pin SFP connector sets to mount and control two SFP transceivers simultaneously.

Product

Magnetic Level Gauge Switches

-

ABB Ltd.

ABB Ltd.

ABB's magnetic level gauge switches for point level alarm and/or control can mount to a KM26 magnetic level gauge or an LS Series cage level switch.These switches are completely isolated from the process fluid as they are magnetically activated by a magnet equipped float (KM26) or attraction sleeve (LS Series). The unique magnetic coupling action eliminates seals, diaphragms, springs, and torque tubes common to other level switching alternatives since there is no physical contact with the process fluid. The magnetic coupling also eliminates process connections to the switch; therefore, no isolation valves are required to block off the switch for maintenance. The switch "set point" is easily adjustable without changing any process piping and the result is a more reliable and easier way to maintain level system.

Product

VME Test Extender 3U/220mm J1

111EXT3122-11XX

-

ELMA Electronic, Inc.

111EXT3122-11XX - ELMA Electronic, Inc.

The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.

Product

VME Test Extender 9U/400mm J1/J2/J0

111EXT9140-0120

-

ELMA Electronic, Inc.

111EXT9140-0120 - ELMA Electronic, Inc.

The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.

Product

VME Test Extender 3U/400mm J1

111EXT3140-11xx

-

ELMA Electronic, Inc.

111EXT3140-11xx - ELMA Electronic, Inc.

The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.

Product

VME Test Extender 3U/220mm Universal

110EXT3122-10xx

-

ELMA Electronic, Inc.

110EXT3122-10xx - ELMA Electronic, Inc.

The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.

Product

Type 12R2, 12U, 19" Rackmount, MIL-Rugged, Vertical

12R2-12U-V

-

ELMA Electronic, Inc.

12R2-12U-V - ELMA Electronic, Inc.

The 12U, 12R2 was designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock to the chassis to less than 10Gs at the card cage and PSU tray.

Product

Electrical Motor Control

-

AOIP

AOIP

For more than 60 years, AOIP is specialized in the starting and control of asynchronous cage or slipring motors over any kind of equipment and in any weather conditions.

Product

VME Test Extender 6U/220mm J1/J2

111EXT6122-012X

-

ELMA Electronic, Inc.

111EXT6122-012X - ELMA Electronic, Inc.

The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.

Product

Type 12R2, 9U, 19" Rackmount, COTS MIL-Rugged

12R2-9U-PC

-

ELMA Electronic, Inc.

12R2-9U-PC - ELMA Electronic, Inc.

The 9U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock-isolated versions attenuate 25G shock to the chassis to less than 10Gs at the card cage.

Product

ARINC818 Cards

-

AIM GmbH

AIM GmbH

> ARINC818 is a specification which has become an Industry standard for the transmission of uncompressed digital video. This commercial standard uses Fibre Channel as a point-to-point communication link for low latency with the ARINC818 defining the packetized protocol for transmission of the digital video information. It is highly flexible and can be used for a variety of onboard display systems in both commercial and military applications. AIM’s ARINC818 cards use our field proven Common Core hardware design giving the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive DDR3 memory and IRIG-B time encoder/decoder functions are standard. The ARINC818 modules are available in PCIe formats.The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for ARINC818 interfaces. The dual core processor provides onboard processing and data transfer capabilities for the most demanding applications including ARINC818 support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized ARINC818 Interfaces enabling the board to analyze incoming data in real time. Each module provides 2 ARINC818 compliant ports. SFP cages make it suitable for different media types as optical or electrical network technologies. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our ARINC818 cards.

Product

Reduced Voltage Motor Starting Panels by Auto-Transformers

-

Hilkar

Hilkar

Reduced Voltage Motor Starting Panels are designed for starting of squirrel cage induction and synchronous motors. A RVMS Panel reduces the torque by temporarily reducing the voltage and/or current input. It reduces voltage applied to the motor during start up causing lower starting currents from the connected grid.

Product

CPCI Test Extender 6Ux180mm

117FFE6018-0XXX

-

ELMA Electronic, Inc.

117FFE6018-0XXX - ELMA Electronic, Inc.

The cPCI extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged on each 2mm HM connector in P1-P5. Each line in rows A-E can be isolated with the DIP switches.

Product

Type 12R2, 14U, 19" Rackmount, MIL-Rugged, Vertical

12R2-14U-V

-

ELMA Electronic, Inc.

12R2-14U-V - ELMA Electronic, Inc.

The 14U, 12R2 was designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs.Shock isolated versions are designed to attenuate 25G shock to the chassis to less than 10Gs at the card cage and PSU tray.

Product

VME Test Extender 6U/220mm Universal

110EXT6122-000X

-

ELMA Electronic, Inc.

110EXT6122-000X - ELMA Electronic, Inc.

The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.

Product

Crowbar Resistors

-

Hilkar

Hilkar

Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.

Product

Autopilot Directional Gyroscopes

4000C/D-series

-

Sigma Tek, Inc.

4000C/D-series - Sigma Tek, Inc.

The 4000C/D is an air-driven directional gyro with A.C. autopilot pickoffs. Left turns produce clockwise dial rotation and right turns produce counter-clockwise rotation. Two knobs control the gyro. The left knob is used to cage the unit, and the right knob is used to select the instrument’s heading. To change course, the right selector knob is pressed and turned to disengage the dial shaft and set the pointer to a new heading. Releasing the selector knob re-engages the pointer with the dial shaft. As the aircraft turns onto a new course, the pointer returns to its original position. The on-course position of the pointer is always at the top of the azimuth circle (0° on the dial with the aircraft headed north).