Test Fixtures
UUT interconnect interchangeable with tester.
See Also: Fixtures, Mechanical Fixtures, Vacuum Fixtures, ATE Fixtures, PCB Test Fixtures, Board Test Fixtures, Bed of Nails, Spring Probes, Test Jigs, Test Probes
-
Product
USB A TX Test Fixture
AUT20135
-
This newly designed AUT20135 brings enhanced user-experience with the following features:
-
-
Product
High Node Count In-Circuit Test Fixtures
HNC Test Fixture
-
Circuit Check continues to be a leading edge provider of custom engineered test solutions with our new Keysight i3070 HNC test fixture. Working with Keysight Technologies during the development of their HNC adapter in 2011, we were the first test fixture provider to offer customers with a solution to test large node count boards. High node count test fixtures can handle greater than 10,000 probes.
-
Product
HDMI
-
SCHILLER AUTOMATION GmbH & Co. KG
HDMI test adapters and test fixture kits facilitate Source and Sink compliance testing and HDMI cable testing. Our products are used in Certification Testing to CEA 1.3b, 1.4a, 2.0 and 2.1 standards. 1080p and 4K formats are supported. We offer A and D style plug and receptacle connectors, male and female SMA leads, with and without HEAC channels.
-
Product
68-Pin VHDCI Male to 68-Pin VHDCI Male, 50 Ω, Shielded Digital Cable
781293-01
Digital Cable
The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
Remote Display Kit for Post.4d
postrd
-
remote display kit for post4d, not RoHS compliant (can be considered test equipment, not subject to RoHS). Connects to PC Engines post4d PCI POST card (will not work with post2b or post5a). 20 inch cable, place display in a more accessible location. Ideal for software development or test fixtures.
-
Product
DDC (Dual DIMM Carrier) DIOS Adaptor
JT 2702/DDC
-
The JT2702 Digital 256 channel JTAG I/O module. JT2702/DDC (Dual DIMM Carrier) is a DIMM DIOS accessory product. It is typically used in custom test adapters or fixtures where a large number of digital I/O channels are required with a minimum space overhead.
-
Product
Manual Test Fixture (MA)
MA 2013/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1700Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 25,00 kg
-
Product
PCIe
SFF 8639 Gen4 (U.2)
-
SCHILLER AUTOMATION GmbH & Co. KG
The 8639G4-TPA-PR test adapter or test fixture kit facilitates Source and Sink compliance testing for SFF-Hosts and Devices. These SFF-8639 Gen4 fixtures utilize the multifunctional connector system supporting single/dual port SATA, dual and MultiLink SAS, and/or up to four (4) port PCIe device configurations. The SFF-8639 Gen4 receptacle fixture will accept devices with plug connectors that are in accordance with SFF-8482, SFF-8630, and SFF-8680.
-
Product
Test Engineering & Manufacturing
-
Whether you require just a test fixture, a complete automated test solution or a build to print service, we will work with you to ensure you get the best return on investment possible. We have highlighted our three key services for you below. Our hardware engineers are regularly trained and certified to ensure best practice. All of our software engineers have certified developer accreditation which means the code we produce is concise, easy to maintain and scalable.
-
Product
Benchtop Automated Functional Test
midUTS
Functional Test
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
Product
6 Sided Bed of Nails Testers
BoxProber Family
-
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
-
Product
Impedance Analysis
S96041B
-
Make impedance analysis measurements of Surface Mount Device (SMD) components on the E5080B vector network analyzer with 16198A-010 10 GHz SMD test fixture.
-
Product
GPS/FMS Universal Test Fixture
TA-3000
-
This panel was designed to give the avionics shop the capability to test and troubleshoot many of the GPS, GPS/COMM and FMS units on the market today. Breakout jacks are provided for both analog and digital signals that need to be monitored or simulated. A data port update jack is provided as well as Arinc 429 and RS232 loopback switches. Switches for Gillham altitude are provided as well as fuel flow adjustments. An array of annunciators and configuration switches are also provided to verify those outputs and inputs. Optional UUT configuration overlays also availabl
-
Product
Safety Test Panel for Mixer
-
SCR ELEKTRONIKS introduces Safety Test Panel for Domestic Mixer with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 20 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. This manual contains information about operating instructions and maintenance of the equipment. Please go through this manual carefully and retain it for future reference.
-
Product
Dedicated Testers
-
Dedicated Testers are often inexpensive due to their low test point requirements, which allow for a reduction in switch cards, especially when compared with a Universal Tester. Ease of setup is accomplished through the utilization of transfer connectors between the fixture and the machine. However, this can contribute to a higher fixture cost than typically seen with a Universal Test Fixture due to the nature of their construction which is labor intensive.
-
Product
EEE Component Testing and Screening Services
-
DPACI performs 100% screening as well as qualification testing on electronic parts supplied to the high reliability commercial, industrial, space, and U.S. military sectors. We generate software and hardware to test microcircuits, discrete semiconductors, hybrids, PEMS, and other EEE electronic components to exact customer and military specifications. Our engineering experience in electronic parts screening, qualification, and in-house test fixture fabrication allows us to provide value added components in a timely manner.
-
Product
PC Based Test Setup for LED Driver of LED
-
The tests are Performed as Prescribed in IS the Panel Carries out high voltage, open circuit and performance tests, one by one and provides indication of the Test results as PASS or FAIL lamp for high voltage test. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 80 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. The entire system is housed in sturdy M.S cabinet with powder coating.
-
Product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
Parametric Test Fixture
U2941A
Test Fixture
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
Product
RF Shielded Test Enclosure, Large, Yet Benchtop Enclosure
JRE 2525
-
Originally designed for testing rack mounted RF Sensing equipment, the roomy JRE 2525 is ideal for large wireless devices such as; Rack Mount Mesh Network AP's, Cellular/LTE/4G Base Stations, Wireless Laptops, Test Fixtures for testing Large RF Modules, and other large RF devices.
-
Product
Exchangeable Test Fixture
MA 2109/D/H/S-5
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 8,50 kg
-
Product
A Popular Combination Of Flex 10 And Flex 20 In A Compact Footprint
Flex 30 ATE
-
A combination of both the Flex 10 and 20 system, the Flex 30 is floor mounted system that maintains a small footprint whilst offering that useful additional space. Generally it is fitted with either the G12 or G12X VPC interface allowing a large number of mixed signal connections to be routed to the test fixture.
-
Product
Test Solutions Services
-
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
Product
Fixture Design
-
TestEdge offers quick, cost effective test fixture design services for low-speed, full-speed, and high-speed devices. Based on our experience in developing high performance test fixtures for a wide variety of devices, test sockets, and tester platforms, we provide a premium quality test and engineering validation environment for everything from high power (40W) to high pin count to high speed ECL to high speed SerDes (3.25Gb) devices.
-
Product
PXI Fault Insertion Switch, 6-channel, Two Fault Buses, 10 A, Hardware Interlock
40-192A-012-HI
Fault Insertion Unit
The 40-192A-012-HI is a PXI fault insertion switch with hardware interlock using solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test:
-
Product
Material Test Machines
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
-
Product
S-parameter Measurement System
DPS21
-
Unlike a coaxial tube type or a wave guide tube type, this method does not make errors caused by air-gap as specimens are not put into a fixture. Practical data can be obtained even at the rough, uneven surfaces where the specimen is placed on.It enables compactness and measuring specimens by plane wave because of direct installment of lens with an antenna.It enables measurement by monitoring S21 and S11 parameter with connections of a test fixture to a vector network analyzer and PC.
-
Product
Hand Held Test Fixtures
-
Manual, or semi-automated mechanical devices designed to secure a Device Under Test (DUT) and provide a stable interface for electrical testing, inspection, or programming.
-
Product
AC Hysteresis Graph Test System
DX-2012M
-
Automatic measurement of the dynamic magnetic hysteresis loop of oriented and non-oriented silicon steel under the condition of 50 Hz, 60 Hz, 400 Hz and 1 kHz, accurate measurement of the static magnetic characteristic parameters such as amplitude permeability μa, loss angle δ, specific total loss Ps, remanence Br and coercivity Hc. With special testing fixture, it can directly measure the iron core and stator core of the transformer.
