Test Fixtures
UUT interconnect interchangeable with tester.
See Also: Fixtures, Mechanical Fixtures, Vacuum Fixtures, ATE Fixtures, PCB Test Fixtures, Board Test Fixtures, Bed of Nails, Spring Probes, Test Jigs, Test Probes
-
Product
Universal Breakout Test Fixture
CA-323
-
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
Product
Fixtures For Testing
-
Columbia offers a wide range of different fixtures and test equipment that are possible to modify according to your needs of testing. Our range of different types of test fixtures goes from ICT, RF, General Purpose, CMP to CMK.
-
Product
Boundary Scan Compliance Tester
QT900
-
Qmax Test Technologies Pvt. Ltd.
QT900 Qscan Test system is designed to provide test solution for both Boundary Scan compliance devices and Non Boundary Scan devices. The System provided with Digital IO’s capable of driving and receiving via JTAG IEEE 1149 standard interface and synchronous to JTAG pins. Both Digital and JTAG test are carried out synchronously. Use of virtual test pin and Edge connector eliminates the need of expensive test fixture strategy.
-
Product
Aircraft Test Set
CA-2100S-07
-
The CA-2100S-07 is a bench mounted, modularized and computer based test set used to service all types of aircraft electronics. It simulates the aircraft environment and replaces a myriad of specialized test fixtures found in the industry.
-
Product
Keying Pin Kit, Receiver/ITA
310118112
Keying Pin Kit
The Keying Pin kit is a way to avoid damaging the contacts within the ITAs and Receivers. Simply insert the longer keying pins into the receiver and the smaller set screws into the ITA to create the pattern needed to isolate your test fixtures so there is no operational mismatch.
-
Product
S-parameter Measurement System
DPS21
-
Unlike a coaxial tube type or a wave guide tube type, this method does not make errors caused by air-gap as specimens are not put into a fixture. Practical data can be obtained even at the rough, uneven surfaces where the specimen is placed on.It enables compactness and measuring specimens by plane wave because of direct installment of lens with an antenna.It enables measurement by monitoring S21 and S11 parameter with connections of a test fixture to a vector network analyzer and PC.
-
Product
CamTrac Z-Axis Test Fixture Kits
CT Serie
-
The CT Series Mechanical Kits, utilizing the patented CAM mechanism1, offset the same precision linear motion. The 'Z' axis motion is ideal for a larger point count mechanical test applications.The CT Series features a hinged 3/8" FR4 probe board, tooling holes for precision alignment, removable sides, precision shafts and cam slide block assemblies, and a pan latch assembly.
-
Product
Test Fixture
16047E
Test Fixture
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
Product
One Port Vector Network Analyser
TE3001
-
The TE3001 One Port Vector Network Analyser is built for the professional who understands the calibration process and has a network analysis task to perform. The unit features a larger output signal than the TE3000 for better noise immunity, and is supplied with a 6 piece custom calibration kit to remove the effect of test fixtures and cables. Together, these features make the TE3001 ideal for broadcast and plasma applications that require a length of cable for connection and may be high in noise or interference.
-
Product
Automatic Test Equipment Machinery
-
Is used to assist wiring fixtures and then test the fixtures for wiring errors. We also can manufacture and/or design custom machinery to your specifications.
-
Product
Headphone Test Fixture
AEC206
-
The Larson Davis Model AEC206 Binaural Test Fixture is the tool for testing supra-aural, circumaural, supra-concha, intraconcha, and insert-type headphones. Preassembled with IEC 60318-4 (711) occluded-ear simulators and TEDS compatible preamplifiers that provide electronic calibration information, the Model AEC206 is user-friendly and easy to learn. Additionally, calibration is a simple process—a custom adapter is included for the Model CAL250 acoustic calibrator or similar device.
-
Product
Spring Clip Fixture
16092A
Test Fixture
Use this test fixture with parallel electrodes for impedance evaluation of both lead and SMD components.
-
Product
CAM/GATE Test Kits
-
The Camgate ™ series test fixtures provide ‘Z’ axis motion and, with the optional floating top plate, makes this series ideal for top side probing. The floating push plate is accurately registered with two tooling/guide pins. The top plate mounting frame is adjustable in .500″ (12.7mm) increments to accommodate top side probing in the lower position, or clearance for PCA’s with tall components in the middle or top position, without the need for riser blocks. Camgate fixtures are available with the most widely used interfaces in the test industry.
-
Product
Test Fixture
OCP NIC 3.0
-
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
Product
Collins Radar Fixture with Gyro Simulator
TA-3A/B
-
This weather radar test fixture is a combination of the established WXT-250 series fixture and the RDR-2000 and RDR-2100 radars so that a single panel will provide many features that are still required today. The gyro simulator built into the panel is usable for either radar being tested and eliminate's plugging in any external simulator. The features for both product lines as shown in their respecting CMM's are provided on the panel so that full testing and alignment of these radars and their system components can be tested and/or evaluated. If you require any changes or other product versions please give us a call.
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Test Fixture
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
Test Fixture
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Adjustable Press Plate Bed of Nails Testers
Protector Adjustable Family
-
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Product
Fixturing Kit
10744A
Test Fixture
The Keysight 10744A fixturing kit includes mounting hardware for a variety of Keysight measurement optics devices. A large base, multiple posts, and other accessories let you build structures -- such as tall, rigid towers -- that place optics in the center of a machine's work zone or wherever needed. The fixturing kit helps meet the physical requirements of a range of measurement applications.
-
Product
Air Data Adapter Test Panel
TA-241
-
AZ-241 Adapter Panel is designed to meet manufacturer's requirements. This panel will allow by the book testing of the air data computer when interfaced with the main air data test fixture. The Scott-T transformer is optional or can be customer supplied. Without the Scott-T your API can read the altimeter resolver directly.
-
Product
Interface Pin
-
Smiths Interconnect offers interface probes for all major test equipment manufacturers. We also provide a variety of interface pins for use in test fixtures.
-
Product
Adjustable Clamshell Bed of Nails Testers
AdjustaBON Family
-
Designed for quick test development. This fixture can be configured to probe almost any circuit board in just a few hours. Once the perfect test is developed, move this light weight fixture out to the production floor to evaluate your production line test strategy prior to buying permanently drilled test fixtures, or while waiting for your drilled fixtures to be delivered. The AdjustaBON competes with the Flying Prober. There are many advantages over the flying prober. Setup is simple and intuitive and can be much quicker than programming a flying prober. Small size provides versatile bench top operation right where you need it. Maintenance costs are insignificant in comparison. The total cost of this fixture is in many cases less than the yearly maintenance cost of a flying prober. It would be possible to buy one of these fixtures every year for the price paid just to maintain one flying prober and it is about 1/20th the purchase price
-
Product
Exchangeable Test Fixture
MA 2112/D/H/S-7/HG/KT-ITA-21
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 16,30 kg
-
Product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Test Fixture
Stopper kit includedYAVCANCON2 for fixture identification not included
-
Product
HDMI SCDC/EDID Controller
AJSC-1
-
The Allion AJSC-1 is a SCDC/EDID Controller that was designed for the latest HDMI 2.1/1.4 source/sink compliance electrical testing. It is used for HDMI source/sink device testing with the aim of controlling and emulating HDMI 2.1/1.4 EDID, SCDC signals. As the AJSC-1 is compatible with test equipment from Tektronix and Keysight, it is truly an adaptable and multi-functional test device.This test fixture can be managed through a serial interface using a terminal emulator software such as Tera Term. Windows-based GUI software is also available.
-
Product
MIPI Test Fixtures & Software
-
The UNH-IOL has been a contributing member of the MIPI Alliance since 2007 and tests all mobile devices looking for MIPI conformance and physical layer testing including C-PHY, D-PHY, DSI, and CSI-2. All UNH-IOL MIPI Test Fixtures and Tools are available to member and non-member companies. Below are just some of the MIPI Solutions we offer. For a full list please visit our MIPI Test Fixtures page.
-
Product
200 Vdc External Voltage Bias Fixture
16065A
Test Fixture
Measure a DUT with up to +/-200 V DC bias and also measure axial/radial lead components
-
Product
RF Shielded Box
LTL Q20001
-
LTL Q20001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL Q20001 RF shielded test enclosure can comfortably house the intermediate and large devices on test such as Laptops, larger test Fixtures and other large RF devices.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
NI Real-Time Test Cell Reference System
780590-35
test
VeriStand Full Development License with NI Standard Service , Include 1 Year SSP
-
Product
Receivers
Series 32
-
Semco’s Series 32 Receivers are the optimal design for interfacing the GR 2270 style (VG) test fixtures. Featuring Semco’s patented CAM/TRAC® design, the Series 32 Receivers provide a locking system that assures consistent contact throughout the entire interface. With a full 5/8″ stroke, the Series 32 Receivers allow additional clearance for coax and custom block applications. They are available with or without vacuum ports. Models include: Bench Top, Slope, 19” Rack Mount, Dual 19 Rack Mount, and Dual Benchtop configurations.
