Polarization Extinction Ratio
a measure of the degree of polarization. Also known as: PER
See Also: Fiber Optic Cable Test
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, V/I Readback, 750 V Isolation
43-752A-011
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 239Ω
40-252-113
Programmable Resistor Module
The 40-252-113 is a programmable resistor module with 2 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Tachometers & Accessories
-
An instrument that measures the working speed of an engine, typically in revolutions per minute (RPM).
-
Product
Coordinate Measuring Machines
-
Novacam's 3D Non-Contact Coordinate Measuring Machines are designed with versatility and superior performance in mind: Precision (better than 1um) Speed (1-30 thousand measurements per second) Simultaneous dimensional and surface inspection Smallest probes measuring 0.9mm in diameter Automation by teaching with joystick Portability
-
Product
PC-based logic analyser
Annie-USB
-
A top-quality 8-channel PC-based logic analyser with probably the highest specifications in its class, this Janatek product is excellent value for money. It captures data at a maximum rate of 500MHz, has a buffer depth of up to 1 Meg samples per channel, and incorporates an 8-bit pattern generator to aid debugging.
-
Product
12-Ch SPST 4A-250VAC 24VDC High Current Power Switching
YAV90PIN
Switch Module
The YAV90PIN board is designed to cover the need to control the available power supplies in a test system to the device under test. A VPC 90 series connector is used as interface with the fixture, guaranteeing more than 20.000 mating cycles. Two connector contacts per relay contact are used.
-
Product
Field Portable Wire Analyzer
Model 2635
-
The perfect tester for field use is rugged, mobile, and lightweight, without sacrificing the functionality and power of a larger system. That tester is found in the Model 2635. Weighing 32 pounds (14.5 kg), this wiring analyzer handles up to 400 test points of Series 10 switching per unit. The 2635 can be powered from any AC source 100-240 VAC or 28 VDC so you can use it anywhere in the world.
-
Product
Surface Profile Gauge
SRT-6223
-
Specially used to take accurate measurement of the peak to valley height of the surface profile of the surface profile of blast cleaned surfaces.specifications:display: 4 digits. LCDRange: 0um to 800um (0mils to 30mils)Accuracy: +5% or +5( whichever is the greater)resolution: 1um (0.1mils)Metric and Imperial switchablePC interface: RS232CMeasurement speed: >30readings per minuteweight: 280gdimensions: 162x65x28mm(6.4x2.6x1.1 inch)operating temperature: 0-50℃ , 80% RHCase: high impact ABSBatteries: 4x1.5v (AAA) Batterystandard accessories included:carrying case: 1 pcoperation manual 1 pcoptional accessory:cable and software for RS232C
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2Ω to 6.97kΩ
40-251-130
Programmable Resistor Module
The 40-251-130 is a programmable resistor module with 2 channels which can be set between 2Ω and 6.97kΩ with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Detectors
-
Optical detectors provide additional analytical detail about your samples. When paired with their accessories, such as flow cells or nebulizers, you can obtain more information per run, fulfilling multiple detection strategy requirements.
-
Product
Empowering Traditional Mass Spec
ZipChip
-
The ZipChip™ separations platform uses integrated microfluidic technology to prepare, separate and electrospray biological samples directly into traditional mass spectrometers (MS). In less than 3 minutes per sample, the cost-effective ZipChip system enables analysis of a broad range of matrices from growth media to cell lysates, blood, plasma, urine, and biopharma products. Each chip provides answers on analytes from small molecules up to intact proteins, antibodies and antibody drug conjugates (ADCs). This platform provides better separation quality than most liquid chromatography (LC) instruments – in a fraction of the time – all with full MS identification behind every separations peak.
-
Product
Curved Needle Test Systems
-
Instron’s Curved Needle Testing System is designed for evaluating surgical and wound closure needles through two specialized testing methods: curved needle puncture testing (per ASTM F3014) and cantilever bend testing. These fixtures assess key performance attributes such as sharpness, coating integrity, and flexural strength. Compact and efficient, the tabletop system conserves bench space while delivering robust functionality. Powered by Bluehill® Universal software, it offers comprehensive control over test execution, data collection, and reporting, along with access to a wide range of built-in calculations.
-
Product
Fixed-Mount Barcode Readers
DATAMAN 370 SERIES
-
DataMan 370 series fixed-mount barcode readers solve challenging direct part mark (DPM) and label-based code applications. With twice the computing power of conventional readers in its class, the DataMan 370 delivers faster decode speeds for greater throughput per facility, even when applications have multiple codes and symbologies.
-
Product
Multi-Channel SMU
-
Up to 4 potential-free channels, U/I measurement unitsMax. 400 V or 100 A per channelTotal output max. 800 W (10 kW in pulse mode)Integrated switching matrix with self-testStandard: 19", 3/6 U
-
Product
PowerPC 405 Board
MS 1533
-
- Virtex 4 FPGA with Embedded PowerPC 405 (PPC405) Core- Up to 450 MHz operation- Tri-mode Ethernet Media Access Controller- A/D Converter Blocks (10-bit / 200 kilo samples per second)- Select IO Technology (Wide selections of I/O standards from 1.5V to 3.3V)- DDR2 SDRAM (256MByte)- Program Storage Flash Memory (8MByte)- Data Storage Flash Memory (8MByte)- Vertex-4 FPGA PROM (4MByte)
-
Product
Probe Only Manipulator
LSP
-
The LSP mounts to standard prober hinge mounts with easy access to service and engineering locations. This reduces the floor space per test cell, saving you significant capital expenses. And you’ll be able to quickly and easily set up your ATE to wafer probe.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, Simplified Current Sink, 750 V Isolation
41-752A-902
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
UHP Moisture Analyzer
5910
-
Using quartz crystal technology for speed, accuracy and calibration stability, the 5910 moisture analyzer is designed for ultra-high-purity (UHP) gas analysis in continuous monitoring and analytical cart applications. The 5910 is sensitive to changes in moisture concentration of less than 500 parts per trillion by volume (pptv), resulting in an accuracy of better than ±100 pptv, or ±10% of the reading.
-
Product
Wind Speed Sensor/Anemometer
ENVIROMUX-WSS
-
Rugged anemometer. 3-cup rotor pressed on a stainless steel shaft. Reed switch and magnet providing one pulse per rotation. Rotor diameter: 5 inches. Speed range: ~ 3 mph to 125+ mph (~5 kph to over 200 kph). Rugged Delrin body with bronze and Rulon bushings. Flat aluminum mounting bracket with 2 holes. esigned to be mounted on top of a pole or bracket. 100 feet of exterior grade wire. Maximum cable length: 1000 ft (305m).
-
Product
16 Discrete/Switch I/O Channels (±80 V, 625 mA/Ch.)
DT2
-
The DT2 module features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
Product
WiFi Traffic Generators
LANforge WiFIRE
-
wireless traffic generator is an excellent choice for testing Access Points and other WiFinetworks. The CT520 uses a modified Wireless driver for WiFi NICs based on the Atheros chipset. It cansupport up to 32 Virtual Stations. Each of the Virtual Stations has its own IP address, IP port space, MACaddress and routing table. The Virtual Stations can be assigned to communicate to a particular AccessPoint, use a particular SSID, and have a WEP (64 or 128bit) or WPA/WPA2 key assigned. More advanced802.1X authentication is also included. There is a single WiFi radio per CT520 but multiple LANforgesystems can be clustered together for more realistic radio interference patterns and increased trafficgeneration capability. The radio supports 802.11 a, b, g or n mode. Transmit power andchannel/frequency is configured on a per-radio basis. Most other settings are configurable per virtualstation
-
Product
Test Program Modules
-
The BRAT Test Program developed will provide functional validation of an assembly based on customer supplied documentation. This does not include hardware (e.g., Interface Test Adaptors), documentation (e.g., technical orders), travel or travel related per diem, or site verification test or installation.
-
Product
Infrasound Measurements
-
Is sound that is lower in frequency than 20 Hz (hertz) or cycles per second, the "normal" limit of human hearing. Hearing becomes gradually less sensitive as frequency decreases, so for humans to perceive infrasound, the sound pressure must be sufficiently high. The ear is the primary organ for sensing infrasound, but at higher intensities it is possible to feel infrasound vibrations in various parts of the body.
-
Product
Compact Temperature Chamber
FB1.5V-UHC Series
-
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 1.5Ω to 3.55kΩ
40-252-123
Programmable Resistor Module
The 40-252-123 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 3.55kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Automated Filter Tester
8127
-
The Automated Filter Tester 8127 is designed to comply with commercial respirator standards around the globe and has a proven track record of durability, reliability, and minimal maintenance, meeting the demanding requirements of manufacturing and quality control environments. Whether you are looking for a stand-alone tester to check a few filters per day or need to integrate your tester in an automated, high volume production line, CERTITEST AFT’s are up to the challenge
-
Product
4-CH 16-Bit 2MS/s Simultaneous-Sampling USB DAQ Module
USB-1210
Data Acquisition Module
The USB-1210 is a 16-bit high-speed USB 2.0-based DAQ module equipped with 4 analog input channels providing simultaneous sampling at up to 2MS/s per channel. The USB-1210 delivers high accuracy and excellent dynamic performance at maximum sampling rates, and flexible trigger functions. In addition, onboard 64M samples FIFO ensures no data loss during acquisition even when CPU or system loading is heavy.The USB-1210 is USB bus-powered and equipped with removable screw-down terminals for easy device connectivity. The attached multifunctional stand can be used for desktop, rail, or wall mounting. Suitable for high-speed data acquisition, laboratory and medical research, the USB-1210 provides a reliable measurement solution at an affordable price.
-
Product
sbRIO-9222, Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
785479-01
Voltage Input Module
Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
Product
GHz Elastomer Sockets
-
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
Product
Synchro and Resolver Angle Indicator
AIT5
-
Computer Conversions Corporation
This series of units were designed to satisfy Hi speed synchro/resolver applications where the output data must be fresh and no data staleness can be tolerated. The tranducers utilized are the same as in the regular MDS series, however different tracking electronics are used. The resultant data tracks the input shaft perfectly and is always fresh and accurate at input speeds up to 64 revolutions per second, depending on the resolution. Data in BCD or Binary formats are available, and clean, unambiguous crossovers are guaranteed.
