Polarization Extinction Ratio
a measure of the degree of polarization. Also known as: PER
See Also: Fiber Optic Cable Test
-
Product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
-
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
Product
Logic Analyzer
LAP-C(16032)
-
Zeroplus Technology Corperation
Bandwidth:75MHzWorking Range: -6V~+6VAccuracy: ±0.1V, Memory:512KbitsDepth(Per Channel):32Kbits (Max 8Mbits for compression)
-
Product
Handyscope TP450-250XM-W5
TP450-250XM-W5
-
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 1 kV Isolation
41-752A-103
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-021
Programmable Resistor Module
The 40-254-021 (PXI) and 42-254-021 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 925Ω with 0.25Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Franklin Tester Model
Model FT2
-
Franklin Tester Model FT-2 is designed as per IS:649 & ASTM:717 Standard to measure insulation resistivity of electrical steel sheet. It requires precision & noise free DC regulated power supply and equally distributed pressure on electrode. Franklin Tester FT-2 regulated power supply provides 0.5000V with 0.1% accuracy over load and no load. Most of national and international standard has specified only 0.5%, means FT-2 is equipped with five time better accuracy than required.
-
Product
Pack (IP) Modules
IP & MM
-
Industry Pack (IP) modules are international standards as per ANSI-VITA 4.These are mezzanine modules of approximately the size of a business card (99mm x 45mm). Featuring a 16 or 32 bit wide I/O interface and 50 user defined I/O pins, these modules are ideal for providing the capability for high density I/O.IP carriers provide multiple slots on a single carrier. This allows multiple IP modules to be provided on a single slot in a Compact PCI / VME / VXI / PCI card cage.Industry Pack modules provide some unique advantages in system integration. These include:
-
Product
96 Sink/Source
YAV90096
Digital I/O
Selectable voltage and current, comparation and measurement Drive sink or source up to 32 mA per channel Maximum voltage in output selectable from 9 to 24 VDC Possibility to use I7Os in parallel Pin voltage comparator with logic readout at fix +4VDC 10-bit resolution pin voltage measurement with CAN bus value readout Build-in editable test steps sequence (test script) Size: form G
-
Product
Bench/System Multi-Range DC Power Supply With Digital Control, 3 Or 4 Outputs, 315 To 420W With/without Remote Interfaces
MX Series
-
Three or four high performance outputs each with full functionalityRange switching gives variable voltage/current combinationsShared power mode provides double power from a single outputLow output noise and ripple via linear final regulationHigh setting resolution of up to 1mV and 0.1mAVariable OVP and OCP trips on all outputs50 setting memories per output plus 50 linked memoriesSelectable voltage tracking (isolated tracking)Selectable current meter averagingSwitchable remote sense capabilityGraphic LCD provides simultaneous output meteringNumeric or spin-wheel control of all parametersIndividual or combined output on/off control with programmable delay sequencing.3U half-rack case for bench or rack mounting (4U rack kit accessory available)RS-232, USB and LAN (LXI) interfaces (P models)GPIB option (P models only)Duplicate power & sense terminals at rear (P models)
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 2.5Ω to 773kΩ
40-251-143
Programmable Resistor Module
The 40-251-143 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 773kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 3Ω to 5.82MΩ
40-252-052
Programmable Resistor Module
The 40-252-052 is a programmable resistor module with 1 channel which can be set between 3Ω and 5.82MΩ with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Extinction Ratio Meter
-
Shenzhen Golight Technology Co.,Ltd
The extinction ratio meter can achieve accurate measurement of up to 40dB PER dynamic range. The instrument is precisely controlled by micro-machines, which can quickly and accurately measure the extinction ratio, polarization angle and optical power of the polarization-maintaining device.
-
Product
Mainframe or -E Expansion Chassis - Control up to 16 Modules with up to 8 Relays per Module
LXA/128-MF
Chassis
These Chassis control up to 16 modules with up to 8 relays per module. A large variety of different switch modules are available to build almost any configuration. Modules are available to build matrix or mux configurations or discrete relay modules. Input detection modules, output driver modules and proto board modules allow custom systems for almost any application. LEDs on the front panel show switch and power status. A thumbwheel manual control is optional.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 62.1Ω
40-252-111
Programmable Resistor Module
The 40-252-111 is a programmable resistor module with 2 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Low Power MIPI Bridging Solution With Integrated Flash
CrossLinkPlus
-
*Instant-on (< 10 ms) configuration with integrated flash memory*Integrated flash enables flexible reprogramming in the field*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per port*11 programmable, source synchronous I/O pairs for camera and display interfacing*Available in small 3.5 mm x 3.5 mm BGA package with 0.4 mm pitch*Comprehensive library of IP and reference designs, compatible with CrossLink
-
Product
128-Pin Hybrid Driver/Sensor Module
HYB04
-
The HYB04 enables comprehensive analog as well as digital driver- and sensor-functions. It has 128 non-multiplexed hybrid pins per module.
-
Product
Demulsibility Characteristics Testers
-
The Labodam Demulsibility Characteristics Tester is designed an dmade as per Test Methods for Demulsibility Characteristics of Petroleum Oils and Synthetic Fluids ASTM D1401
-
Product
STD Bus, Vectorbord Plugbord
4610-3
-
VECTOR Electronics and Technology, Inc.
56 Gold plated edge contacts (28 each side)on 0.125"(3.175mm) centers.Pad per hole and peripheral buses both sides.Row and column legends provided.
-
Product
PCIe Mini Module
PCIe-Mini-ESCC
Controller
The PCIe-Mini-ESCC module is a Dual Channel serial communication controller with 4K FIFO per Line. The PCIe-MiniESCC module is based on the Z85230 Enhanced Serial Communication Controller, with larger FIFOs and several SDLC improvements from Zilog.
-
Product
Precision Programmable Attenuator
RCDAT-30G-30
-
Mini-Circuits’ RCDAT-30G-30 is a precision programmable attenuator covering an extremely wide bandwidth, from 0.1 to 30 GHz. Its unique design allows attenuation settings to be programmed from 0 to 30 dB, in 0.5 dB steps with monotonic attenuation change per dB, even at the highest frequencies and attenuation settings. The attenuator can be controlled via USB or Ethernet, allowing control directly from a PC, or remotely over a network. VHF / UHF / L / S / C / X / Ku / K band testing.
-
Product
Register
Trend Viewer
-
A trend is a diagram facilitating analysis of long records of measured sensor values (for hours, days, months, years). Based on the sampling frequency, an n number of counts per second are performed, and their yearly number equals to 31,556,926*n. If the user needs to evaluate short-term moments of the source signal, then there is no difficulty. It is much more difficult, when it is necessary to evaluate the parameters for the entire year or several years, and no monitor and no person would handle it. And this is the case when trend building could help.
-
Product
Hot Sticks
HS-120
-
Standard Electric Works Co., Ltd
● Used for the extraction of fuses, isolators & fuse switch disconnections.● Can be attached to the 275 HP Proximity Detectors and contact Capacitive Detectors 21× HVD.● Universal "sunrise" head attachment to fit special tool fittings.● Head Section rated at 100kV per 300mm (5 min).● Comes complete with sunrise fitting and fuse extractor.● 3 × 1.8 meter sticks; 1 × 1.2 meter head section.● Sticks 1 × 1.2 meter head section complete with universal sunrise fitting. ● 1 × carry bag. ● Meets IEC 60855.
-
Product
2-port 10GbE PoE PCI Express Card
AX92324
-
Intel® Ethernet Controller X550-AT2, up to 10 Gbps data rate, Supports 15.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 25.5W per port, PCI Express x4 compliant, PoE power on/off via Power Manager software and API, Operating temperature range from 0°C to 55°C
-
Product
Oscilloscope, 200 MHz, 4 Input Channels, 2 GS/s interleaved, 200 Mpts - interleaved
T3DSO2204A
Oscilloscope
200 MHz, 2 GS/s per Ch, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO with 10.1" Color Display.
-
Product
6U OpenVPX 6 Slot Profile BKP6-DIS06-11.2.18-3
1OVX606MZ3-1X01R
-
VPX mesh, 4 lane Fat Pipe, QFP expansion plane, up to 6.25 Gbps per channel.
-
Product
Data Logging System
SPARTAN
-
SPARTAN is an affordable, compact multi-channel measuring system specially designed to optimize potential-isolated measurement of voltage and temperature. With a sampling rate of up to 10 kHz per channel, even highly dymanic processes can be recorded with high resolution.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, 750 V Isolation
43-752A-013
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Compliance Test Systems
LMG Test Suite
-
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
Product
Switch Modules - 16 Single Pole Relays Arranged as an 8x2 Matrix
JX16/AB-1
Switch Module
This module has 16 single pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
-
Product
Light Meter
PLMT68
-
Light Meter Measures In Lux and Foot Candles (User Selectable)Over-Range IndicatorAuto RangingPeak Hold, Max and Data HoldRelative ModeLong-Life Silicon Photo Diode InsideMeasurement Rate: 1.5 Times per SecondMax Range: 400,000 LuxAccuracy: +/- 5% Under 10000 Lux, +/- 10% Over 10000 LuxMax Resolution: 0.1 Lux/FCAccessories Included: 9V Battery, Carrying Case, Photo DetectorDimensions: 6.50' H x 2.99' W x 1.69' DWeight: 14.22 oz.Sold as : Unit
