Polarization Extinction Ratio
a measure of the degree of polarization. Also known as: PER
See Also: Fiber Optic Cable Test
-
Product
Wind Speed Sensor/Anemometer
ENVIROMUX-WSS
-
Rugged anemometer. 3-cup rotor pressed on a stainless steel shaft. Reed switch and magnet providing one pulse per rotation. Rotor diameter: 5 inches. Speed range: ~ 3 mph to 125+ mph (~5 kph to over 200 kph). Rugged Delrin body with bronze and Rulon bushings. Flat aluminum mounting bracket with 2 holes. esigned to be mounted on top of a pole or bracket. 100 feet of exterior grade wire. Maximum cable length: 1000 ft (305m).
-
Product
PCIe-7841, Virtex-5 LX30 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device
781100-01
-
Virtex-5 LX30 FPGA, 200 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7841 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7841 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
Software for Configuration, Logging and Analysis
LMG-CONTROL
-
ZES ZIMMER Electronic Systems GmbH
Real-time display of configuration and measuring valuesTransfer of up to 3000 measuring values per secondTimestamps with a resolution of 1 millisecondVersatile analysis of sampling valuesExport of measuring values to other applications
-
Product
STD Bus Backplane
-
VECTOR Electronics and Technology, Inc.
Vectorbord® STD Bus industrial backplanes per IEEE 961 microcomputer bus, compact and rugged are fully assembled and tested. Designed for 4.5” X 6.5” plug-in boards, Vector STD Bus backplanes are available in 8 or 16-slots. Speed capability up to 10MHz; 2-layer design. Ample positions for decoupling capacitors; interrupt priority lines.
-
Product
High Pressure Gas Conditioners
HPG
-
Bemco HPG, High Pressure Gas Conditioners are similar to the PTS Portable Temperature Conditioners except they are designed for continuous operation at up to two atmospheres (29.4 psia) of pressure. This higher base operating pressure doubles the gas density per cfm of circulating air or gaseous nitrogen allowing the use of smaller connecting tubes while also increasing thermal capability. .
-
Product
Master Controller
RatMaster
-
- Jumper free configuration- Intuitive configuration software- RS-232, TTL and CI-V interfaces- Automatically generates Icom CI-V data stream from non-Icom radios- Configurable band limits- Built-in USB interface- Set default antenna per band- Field upgradeable firmware- Anodized aluminum case- Laser engraved panels
-
Product
12-/16-bit 16 Channel DAC for PCI
PCI395
-
The PCI395 features 16 analog voltage outputs, integrated on the factory standard, ANSI certified M-module standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel).
-
Product
Programmable Industrial USB 3.0 Hub (8 Ports)
-
The USBHub3+, an 8-port programmable USB 3.0 Hub. Designed by engineers for engineers - connect the USBHub3+ with confidence to expensive lab or production equipment. Enable/Disable any Downstream Port. Maintain selectable control of data, SS lines, power lines for any port. Monitor Voltage and Current on any/all ports. Supply up to 2.5A per port. Set Current Limits on any port. Select between two (2) Host Connections.
-
Product
Surface Analysis
Dimension FastScan Bio
-
The Dimension FastScan Bio Atomic Force Microscope (AFM) breaks longstanding barriers to provide routine high-resolution research of biological dynamics, with temporal resolution up to 3 frames per second for live sample observations. Furthermore, it does this while making the AFM easier to use than ever before.
-
Product
NI-9216, 8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
785186-01
-
8-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9216 is a resistance temperature detector (RTD) input module. You can configure the NI‑9216 for two sample rate modes: high sample rate or high resolution. The NI‑9216 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3-‑or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9216 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Multi-Interface Frame Grabber
Xtium2 CXP PX8 Series
-
The Xtium2™-CXP PX8 series is based on the industry standard PCI Express™ Gen 3.0 and CoaXPress ver 2.0 to transfers image data to the host memory at maximum acquisition rates. The Xtium2-CXP series takes full advantage of PCIe Gen 3.0 platform using PCIe x8 slots to deliver bandwidth up to 6.4GB/sec into the host memory while supporting image acquisition from up to 4 CXP12 input channels (12.5Gbps per channel). The Xtium2 CXP series is available in three configurations:
-
Product
Eight-channel USB Voltage and Thermocouple DAQ
Model DI-2008
-
Includes DI-2008 instrument, WinDaq software, calibration certificate, terminal screwdriver, and USB cable (6-feet). Eight differential and isolated analog input channels. Seven bi-directional digital input ports, including: Counter input for totalizing applications, Rate input for frequency/flow/rpm applications. ChannelStretch™ channel expansion to 128 analog and 112 digital channels. Programmable voltage and thermocouple measurements per channel. 10 mV to 50 V programmable range per channel in 12 steps.
-
Product
Vehicle Testing
-
short testing times, thereby enabling a large throughput of vehicles;objective, operator independent test results on most test items;accurate measurements;a large set of clear user instructions is displayed, which allows the owner/ driver to stay in the vehicle during the test, thus saving manpower;a wide selection of different test equipment for integration is available;a large number of settings, threshold values and standards can be accessed directly and edited by the user;the modular setup allows a complete variety of Test Lane configurations;easily upgradable by adding more test equipment items per lane;easily expandable by adding more Test Lanes;integration of Test Lanes on remote sites is possible;link up to Government database and remote access possibilities where applicable.
-
Product
Short Test Pin Probe 13
CX-13
-
Shenzhen Chuangxin Instruments Co., Ltd.
Short Test Pin Probe 13 Used to test accessibility through enclosure openings per IEC, EN, UL and CSA Standards.
-
Product
Signal Board
iDSC 1816
-
The iDSC 1816 board from Microstar Laboratories combines 16-bit resolution on eight simultaneous channels of data acquisition with brick-wall anti-alias filters on each channel. The iDSC 1816 samples analog inputs at a throughput of 1.2M samples per second, with the sampling rate on each channel ranging from 8 samples per second to 153.6k samples per second.
-
Product
Octal ASI Ports for PCIe
DTA-2178-ASI
-
Eight bi-directional ASI ports on a low-profile PCIe card at a price of about €100 per channel. Each port is configurable from software as input or output.
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-02
-
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
Automotive Diagnostic Scope
ATS610004D-XMSG
-
Automotive oscilloscope with 4 differential channels, 1GS/s, 250MHz BW, 12/14/16 bit, integrated SureConnect connection test, SafeGround single-ended connection option on each channel, and up to 257 MSamples memory per channel.
-
Product
Monochromators
-
Diffraction gratings are specified by a line density in grooves per millimetre. The higher the density, the greater light is dispersed resulting in a relatively limited spectral extent. Furthermore, in general , the higher line density gratings are optimised for short wavelength use and vice versa. One must take into account the available grating(s) and the operation range of such before deciding how many gratings are required to cover a given range. Where multiple gratings are required, one can opt for a multiple-grating monochromator which would allow performing a spectral measurement over a great range, or whether a single (interchangeable) grating monochromator is used and the measurement performed in two or more parts.
-
Product
HandyScope HS6-DIFF With SafeGround With SafeGround & SureConnect
HS6-DIFF-100XMSG-W5
-
- 1GS/s sampling and flexible resolution of 8-16 bit.- Four input channels up to 250 MHz analog bandwidth- Highly accurate 1 ppm time base- DC Accuracy of 0.25 % and 0.1 % typical- Very fast 200 MSamples per second USB streaming Data logger- Spectrum analyzer with 32 million bins- Optional SureConnect connection test on all channels- Up to 256 MSamples memory per channel
-
Product
Fire Control Computer
58MD3-01
-
- 3Ø, 115 VAC input per MIL-STD-704A- Holdup time- Triple outputs, 160 Watts- Continuous Background Built-In-Test (BIT)
-
Product
Regenerative Battery Pack Test System
17020E
-
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Computed Radiography
FCR CAPSULA X
-
A compact system with throughput of up to 72 images per hour, ideal for smaller facilities with variable caseloads or remote applications.
-
Product
16 Bit PXIe Gen-3 Digitizer With 4 Channels 500 MS/s And 4GS Memory
RazorMax / CSX 165G4
-
The new extremely fast and high-resolution Gage digitizers of the series RazorMax Express CompuScope offer with a 3U Single slot PXI Express card a resolution of 16 bit and a sampling rate of 1 GS/s (per channel).
-
Product
PXI 10W Programmable Resistor Module, 2-Channel, 1Ω to 122Ω
40-253-012
-
The 40-253-012 is a programmable resistor module with 2 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
High Accuracy (0.045%) Precision Multi-Channel Harmonic Power Analyzer
PA910
-
The PA910 power analyzers offer expanded power analysis options. The PA910 offers ultra high 0.045% power accuracy for all channels and improved voltage and current self-heating adders over those of other power analyzers. In addition, the PA910 provides easy channel selection for the user while offering 100 full precision readings per second and measurement bandwidths sufficient to handle 5 MHz waveforms.
-
Product
PXIe-4330, 25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module
781346-01
-
25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module—The PXIe‑4330 is a simultaneous input module that provides integrated data acquisition and signal conditioning for bridge-based sensors. The PXIe‑4330 includes increased accuracy, high data throughput, and synchronization features, making it ideal for high-density measurement systems. To remove noise, the PXIe‑4330 offers antialiasing and digital filters per channel. Each channel also features an independent, programmable excitation voltage. Additionally, the PXIe‑4330 provides remote sensing, internal bridge completion, and shunt calibration options per channel.
-
Product
Cable Diagnosis System
Baseline 9400 TDR/ICE
-
K&S Engineering and Scientific Ltd
BASELINE 9400 TDR/ICE - the unique cable diagnostic system: - A state-of-the art cable fault locating instrument containing a high speed data recorder, capable of capturing and evaluating 40 million samples of electrical data per second, while also featuring amplifiers, attenuators and an adjustable pulse generator.
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function PXI modules
PXI-2500 Series
-
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
Product
Schildknecht Flexing Tester
-
TESTEX Testing Equipment Systems Ltd.
Schildknecht Flexing Tester is designed to determine the resistance of coated fabrics to damage by flexing due to oscillation at 500 times per minute. Schildknecht Flexing Tester complies with ISO 7854, BS 3424, etc.
