Polarization Extinction Ratio
a measure of the degree of polarization. Also known as: PER
See Also: Fiber Optic Cable Test
-
Product
Polarization Extinction Ratio Measurement
-
Rapid & Accurate measurement for PER, Angle, and Power. The most suitable light source for PER measurement.
-
Product
Enhanced 24 Discrete I/O Channels (0 to 60 VDC, 500 mA/Ch.)
DT4
-
The DT4 module (the enhanced version) features 24 programmable channels for either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3 – 60 VCC source. These modules can sense broken input connections and whether an input is shorted to +VCC or to ground. Additional features of the DT4 (Enhanced Version) are listed below.
-
Product
PXIe-6591, 12.5 Gbps, 8-Channel PXI High-Speed Serial Instrument
783638-01
Serial Interface
12.5 Gbps, 8-Channel PXI High-Speed Serial Instrument—The PXIe‑6591 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex‑7 FPGA to implement various high-speed serial protocols, and it is programmable with the LabVIEW FPGA Module for maximum application-specific customization and reuse. The PXIe‑6591 takes advantage of FPGA multigigabit transceivers and up to eight TX and RX lanes. In addition to high-speed serial lanes, the PXIe‑6591 features digital I/O signals that support multiple logic families with per line, per cycle direction control.
-
Product
Programmable AC Laboratory Power Supplies, Current-controlled
-
*Fast regulation of the current*Voltage depends on the load*Current and voltage values are configured based on the customer's actual requirements*Power from 250VA to 36kVA*Output voltages 1VAC to 300VAC*Maximum currents up to 2000A per phase
-
Product
Walk-In Test Chambers
-
HIACC Engineering & Services Pvt. Ltd.
HIACC design & assemble a wide range of walk-in/drive-in test chambers. The construction model includes Integral Welded Floors, Pre-Fabricated Modular Panel construction and Compact Walk-In chambers. The Integral welded floors is adopted for heavy-duty testing with ramp rate more than 10°C/min and is ideal for high soak period testing. This is customised as per customer’s requirement.
-
Product
Biconic Logarithmic Periodic Antennas
Stacked LPDA
-
The stacked Logarithmic Periodic Dipole Antenna consists of two ordinary Log.-Per. structures. The excellent characteristics (flat gain over a large bandwidth, low SWR) of the ordinary Log.-Per. designs could be maintained using the stacked LP design. The stacked design helps to focus the directional pattern of the H-plane somewhat, resulting in a typical gain improvement of ca. 2-3 dB compared to an ordinary LPDA. This is especially important for immunity testing, where a maximum fieldstrength and a good field uniformity is required. The beamwidth in the E-plane and the H-plane are nearly identical, providing an optimised illumination of the EuT with minimised ground reflection influence. Further the STLP 9128 C has an excellent cross-polar rejection.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
PXI Device Power Supply - 4 Isolated Channels, 20-bit Measurement Resolution
52310e series
Programmable Power Supply
Chroma 52310e Series i s a programmabl e PXI-Express DPS (Device Power Supply) Card designed for high-accuracy and reliable output power for device test applications. Its compact size, easy level of integration, and high flexibility make the 52310e Series ideal for multi-channel power supplies. Chroma 52310e Series features 8 selectable control bandwidths to ensure high speed output and stable operation; multiple current measurement ranges with a 20-bit DAC/ADC provide the highest resolution and accuracy with a sampling rate up to 600K S/sec; programmable internal series resistance for battery simulation. Chroma 52310e DPS series has a patented hardware sequence engine that has deterministic t iming to cont rol each DPS channel. The sequencer's on-board memory can store up to 1024 sequencer commands and 32k measurement samples per channel.
-
Product
Test Sockets
-
socket design as per customer specificationsquick + easy socket changehigh-performance spring probesdesigned for high frequency up to 16 GHz-55C/-67F to 150C/302F temperature rangemanual/automatic application optionssmall socket footprintone socket base for each insert (3x3 to 9x9 QFN)one-click switch from engineering to production socket modedevice dependent standard socket frame with changeable insertmore than 500,000 compression cyclesKelvin test applicabilitytool-free insert + actuator exchanges0.3 mm minimum lead pitchQFP extender available
-
Product
SHB12X-H3X24, Male InfiniBand to Differential Flying Leads, Shielded LVDS Cable, 1.5 m
196236-1R5
LVDS Cable
72-Pin, Female Flying Leads to 48-Pin, Male InfiniBand, 100 Ohm, Shielded LVDS Cable - The SHB12X-H3X24 LVDS Cable connects the 12X InfiniBand connector on PXIe-656x LVDS digital instruments or some NI 658x LVDS Adapter Modules for FlexRIO directly to individual header pins. This cable is intended for use with a custom breakout fixture. The flying-lead cable has three signals per grouping for positive, negative, and ground pin connections designed to plug directly into any 0.1 in. header connector. It is a shielded, 100 ohm cable.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 6.97kΩ
40-251-024
Programmable Resistor Module
The 40-251-024 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 6.97kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Computed Radiography
FCR CAPSULA X
-
A compact system with throughput of up to 72 images per hour, ideal for smaller facilities with variable caseloads or remote applications.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 1.5Ω to 925Ω
40-251-121
Programmable Resistor Module
The 40-251-121 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 925Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
NI-9217, 4-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module
779592-01
Temperature Input Module
4-Channel, 400 S/s Aggregate, 0 Ω to 400 Ω, PT100 RTD C Series Temperature Input Module - The NI‑9217 is a resistance temperature detector (RTD) input module. You can configure the NI‑9217 for two sample rate modes: high sample rate or high resolution. The NI‑9217 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per channel current excitation. The NI‑9217 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
CLAMP ON CTS
P50
-
Beijing GFUVE Electronics Co.,Ltd.
The P50 is a general purpose 1000A AC current probe designed for use with DMMs, loggers and other instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw.
-
Product
COM Express® Type 2 Reference Carrier Board in ATX Form Factor
Express-BASE
Computer on Module
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time. The average time to design a carrier board is less than half the time of a full custom OEM board.
-
Product
Automatic Softening Point Tester
LD-LSPT-A10
-
Automatic softening point testerLD-LSPT-A10is a bench top microprocessor controlled analytical unit that determines the softening point of two samples at once. Operated via touch panel it uses ball and ring apparatus for reliable detection. Designed as per Test methods of Bitumen and Bituminous Mixture for Highway Engineering and ASTM D36 Standard test method for Softening of Bitumen (Ring-and-Ball Apparatus) it is ideal for determining the softening points of petroleum asphalts, coal pitch, liquid petroleum asphalt, etc.
-
Product
Oscilloscope, 100 MHz, 4 Input Channels, 2 GS/s interleaved, 200 Mpts - interleaved
T3DSO2104A
Oscilloscope
100 MHz, 2 GS/s per Ch, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO with 10.1" Color Display.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, 1 kV Isolation
41-752A-113
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Digital Optical Transport
-
The ATX GigaWave digital optical transport portfolio is designed to fortify cable operators with maximum flexibility and cost efficiencies to support a range of applications and business models. The GigaWave Digital Link Extender (DLX) is optimized to support distributed access architectures (DAA), including Remote PHY (R-PHY) and Remote MACPHY (R-MACPHY), as well as Passive Optical Network (PON), Small Cell/5G and enterprise business services. The GigaWave Digital Link Amplifier-HUB (DLA-HUB) is a field-hardened, gain-flattened EDFA platform that enables the elimination of physical hub sites along long-reach optical routes. The GigaWave digital optical transport portfolio also enables MSOs to leverage the advantages of digital optics over analog, including the capability to transport signals over longer distances and provision additional wavelengths per fiber.
-
Product
Gas Analyser
LT GasAnalyzer
-
Highly performant analyzer for measuring the concentration of technical gases based on a thermal conductivity sensor, an infrared sensor a para magnetic sensor or combinations of these sensors. Sensors are precise, robust and have a low cross-sensitivity. Extractive online measurement of the concentration of flammable or non-flammable gas components in gas mixtures. Can measure trace oxygen (O2) levels in the parts per million (ppm) range.
-
Product
Socket Wrench Torque Sensor Rotating Type
RSS SERIES
-
Our RSS Series rotating socket wrench torque sensors are available in ranges from 10 ft-lbs. through 250 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. Unlimited rotation of the ball bearing supported sensor shaft allows monitoring of the total fastening cycle. The sensing element incorporates bonded foil strain gages of the highest quality, along with coined silver slip rings and two silver graphite brushes per ring for data transmission.
-
Product
Energy Meters
Rj-7600
-
The Rj-7610 Single Channel Energy Meter works with a variety of probes – pyroelectric, silicon, and thermopile – to measure true energy per pulse from single-shot to 40 Hz, picojoules to Joules, UV to far-IR. Sets of 10 or 100 pulses can be statistically analyzed (mean, minimum, and maximum energies, standard deviation), and data can be transferred to computer via the IEEE-488 GPIB computer interface or using the 0-10 VDC analog outout.
-
Product
Octal Small Form Factor Pluggable Electrical Interface
-
Eoptolink Technology Inc., Ltd.
Eoptolink is developing OSFP(Octal Small Form Factor Pluggable) a new pluggable form factor with eight high speed electrical lanes that will initially support 400 Gbps (8x50G or 4x100G). It is slightly wider and deeper than the QSFP but it still supports 32 OSFP ports per 1U front panel, enabling 12.8 Tbps per 1U switch lot. OSFP is designed to support the next generation of 800G optics modules that will use eight lanes of 100Gbps, and offers backwards compatibility with 100G QSFP.
-
Product
Sky Quality Meter
SQM-LR
-
An RS232 SQM model for night-time sky brightness monitoring! An affordable meter for continual, connected measuring of sky brightness for astronomers! The "Sky Quality Meter - LR" measures the brightness of the night sky in magnitudes per square arcsecond.
-
Product
Pressure Recorders
-
AMETEK Sensors, Test & Calibration
Our recorders are capable of storing gauge pressure, absolute pressure, temperature, current, and voltage. They can collect readings as quick as ten times per second, and can store up to 1 million data points. The included easy-to-use software communicates with the recorders and then saves the data into industry standard spreadsheets or tamper-proof pdf documents. With the nVision family, recorded runs can also be viewed on the graphical display of the unit itself.
-
Product
Logic Analyzer
LAP-C(16032)
-
Zeroplus Technology Corperation
Bandwidth:75MHzWorking Range: -6V~+6VAccuracy: ±0.1V, Memory:512KbitsDepth(Per Channel):32Kbits (Max 8Mbits for compression)
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 470Ω
40-251-114
Programmable Resistor Module
The 40-251-114 is a programmable resistor module with 4 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Bench Power Supply
E3630 Series
-
When your requirements demand more power, the E3630 Series power supply offers up to 200 W per output. This linear power supply meets the requirements of the most demanding applications in R&D design verification, production testing, and quality assurance (QA) verification with reliability you can count on.
-
Product
Quad Channel Serial Communication Controller
CPCI-SCC04-ISO
Controller
The CPCI-SCC04-ISO Module is a quad Channel serial Communication controller with 2K Fifo per Line. The CPCI-SCC04-ISO module is based on 4 enhanced Z85233, with larger FIFOs and several SDLC improvements from Zilog. This module provides four synchronous ports up to 230 kbaud synchronous ports and up to Data Rates up to 5.0 Mbit/Sec full-duplex channels, with an independent baud rate generator for each channel.
