Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
Product
Electricity Meter Test Equipment
-
The Reference Standard RS is precision standard meter in single- and three-phase version for electrical power and energy measurement. It is designed to meet all requirements put on a reference standard in a single- and three-phase electricity meter testing and calibration systems. The Reference Standard can be set to any true or artificial mode of operation in three phase system and is capable to evaluate individual quantities in any phase
-
Product
Dual Polarized Antennas
-
Dual polarized horn antennas are offered as both standard and custom models with rectangular waveguide interfaces for both horizontal and vertical ports. These dual polarized horn antennas support both linear and elliptical polarized waveforms. When the antenna receives a circular polarized waveform, equal amplitude linear polarized waveforms are output at both horizontal and vertical ports. When two equal amplitude linear polarized waveforms are input into the vertical and horizontal ports, the antenna will transmit a circular polarized waveform. The listed models offer 15 dB nominal gain and 33/28 degrees typical half power beamwidth at the center frequency of the band. They also exhibit 40 dB typical port isolation and 35 dB nominal cross polarization. These antennas cover full waveguide bandwidths within the frequency range of 8.2 to 110 GHz. In addition to the models listed below, models with 10, 20, 23 and 25 dB gain and other frequency bands are also available.
-
Product
Controllers
BKM91PN
-
Clockwise and/or counter-clockwise rotation of the wand is programmable allowing an optimum adaptation to the machine.The scanning intensity is adjustable in 8 steps. Even rotating drills with small diameters can be checked.The scanning results are display as "OK" or "KO" and signaled by LEDs on the front side of the device.The PROFIBUS is a standard Sub-D 9 pin connection; the USB connection is a USB-mini plug / type B and meets the 2.0 specification.Three digital inputs serve to activate the functions "Teach-in" to learn the position to be scanned, "Start" to initialize the scanning process and "Configurable" for receiving a stop command.Two digital outputs provide the signals for the message "OK" or "KO".The relay contacts are configurable as N/C or N/O connections. They can be set as momentary (valid with start or timed) or latching.Convenient configuration software for programming and setting of tool data is available at no cost.Mini USB for PC connection3 digital control inputs (positive or negative logic) Start and teach signal One configurable input2 relay outputs selectable as N/C or N/O contact Signal all clear message ("OK") Signal error message ("KO") Scanner connection4 LEDs for status display Opening for top hat plug for optional connection to I/O extension module Din rail mounting
-
Product
ATR Enclosures
-
Elma Air Transport Rack (ATR) enclosures offer a standardized, cost effective solution for VME, VME64x, CompactPCI, VXS, VPX and Small Form Factor (SFF) based applications.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781775-01
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
Phase Noise Generator / Calibrator
PNG-A
-
Noise eXtended Technologies S.A.S.
The PNG-A is a high precision generator used in Test and Measurement instruments calibration. It is a Signal Generator with precisely computed phase and amplitude noise characteristics. With its wide frequency offset range, 1Hz to 1 MHz offset, and its programmable Phase and Amplitude noise in real time, this is the ideal standard to calibrate phase noise analyzers, Signal Source Analyzers and Spectrum Analyzers.
-
Product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Bias Ball Probe
POGO-1P-4
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
VME64X 6U 14 Slot with P0
101V64XC14-0621
-
6U VME64x Backplane 14-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension standard. Includes termination passive inboard, daisy chain automatic active, and power bugs on top and bottom of slots.
-
Product
Semiconductor
-
You can find Spring probes used for test process for production of semiconductor here. Spring probe is probe with spring inside and is also called Double-ended probe and Contact probe. It is assembled in IC socket and becomes electronic path, which vertically connects Semiconductor and PCB. By our excellent machining technique, we can provide spring probe with low contact resistance and long life. “MARATHON” series is our standard lineup of spring probe for testing semiconductor.
-
Product
CAMGATE Test Kits
Series 453
-
LThe GR Series 453 CAMGATE mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 453 provides interface compatibility using the GR2270 Style, 12 block interface. This interface accepts the industry standard I/O, power, and coax blocks. The CAM/GATE utilizes a cam roller system for precision guiding and smooth operation and 1.00” push plate movement. The gate assembly is movable to three different positions which allows for the versatility of top side probing, or relocating the frame assembly for PCA’s the have tall components.
-
Product
DCA-M High-Accuracy, Low-Cost Solution for Optical Waveform Analysis
N1090A
Oscilloscope
The N1090A DCA-M builds on that legacy by using the high-performance elements of 86100 and 86105C. It can be configured to perform thorough optical transmitter compliance tests at a variety of standard data rates from 1.244 to 11.3 Gb/s and come with 20 GHz electrical channel in option.
-
Product
Brake Testing
-
Vehicle Brake Test and ABS TestingWe offer an easy-to-use measurement system for brake testing and ABS testing according to ECE, ISO, FMSSV, and SAE international standards. Our test system offers automated workflow, is flexible and robust and used for brake R&D, brake comfort and vehicle testing with regenerative braking. High-accuracy GPS and IMU hardware are available to achieve the highest possible velocity and distance accuracy.
-
Product
Light Meters & Sensors
-
The light meters and sensors product line at Gamma Scientific is extensive. Find sensors, light meters, photometers, radiometers, reference standard detector systems, and transimpedance amplifiers that meet your testing requirements.
-
Product
Multi-Station Test Frame
6800
-
The 6800 Series Multi-Station System offers enhanced throughput with its ability to perform simultaneous, independent tests on up to five (5) separate specimens using a single load frame. Based on our standard 68TM-30 testing frame (30 kN capacity)*, this system is especially suitable when test times are lengthened due to high elongation or slow test speeds.
-
Product
Standard Digital Multimeter - Auto Ranging
MM39
-
The MM39 is an auto-ranging multimeter with a large rotary switch for easy selection of the required test, even when wearing gloves. There are two test buttons, one to lock the range and the other to hold the results which are displayed on a 3½ digit LCD screen.
The main test functions are AC voltage and DC voltage and current and resistance. The MM39 measures both AC and DC voltage between 0.1mV to 600V and AC and DC current between 10mA to 10A. There is a diode test and an audible continuity test which sounds at less than 25Ω.
-
Product
MIL-STD-1553 MCH
M4K1553MCH
-
The M4K1553MCH interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M4K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M4K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
Product
VME / VME64x Backplanes
-
All Elma Electronic VME backplanes are designed to maximize performance, minimize noise, and to give the customer the most reliable, cost-effective product possible. The Elma Electronic VME64x backplane series is designed to fully comply with the ANSI/VITA VME extension standard.
-
Product
System on Demand (SoD): HiL Test System
-
System on Demand (SoD) is a unique, agile and standardized principle to design HiL test systems. SoD shifts the focus away from technical-only solutions to a proven automated design process – targeting our customer‘s real issues: time, budget and flexibility.
-
Product
pH Meter pen type
pH 703
-
High quality, light weight and compact design. Measure water pH fast and easily in many fields such as swimming pools, aquariums, cooling towers, water and wastewater treatments, sanitation plants and laboratory applications. High resolution 0.01pH and high accuracy +/- 0.02pH. Comes complete with protective carry case and standard pH7 buffer solution
-
Product
Dual-Channel, Tri-Port Per Channel, for Extended Cabling up to 20 Meters
FW1
-
The FW1 provides IEEE 1394 (Firewire) high-speed serial communications. The module is provided with a direct PCIe interface to the local (on-board) processor, or, an external host processor for board platforms that support external PCIe connectivity. These module(s) are not supported with the classic memory register-based NAIBrd Software Support Kit (SSK) API libraries. These communication function modules support device control and management via standard native OS (Linux) FireWire device driver.
-
Product
Helix Antennas
-
CAES Helix Antennas are designed with over 60 years of antenna design expertise. Available in both normal and axial modes, CAES Helix Antennas are standard equipment on electronic warfare systems worldwide and deliver the performance required for today’s most demanding defense applications.
-
Product
USB Modular Source Measure Unit
U2722A
Source Measure Unit
The U2722A USB Modular Source Measure Unit is a 3-channel 20V/120mA that can operate in a 4-quadrant operation. The channels could be connected in series or in parallel to achieve up to 60 V/360 mA. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
-
Product
Micro Coax, Two Piece Contact, Receiver, PCB Vertical Mount, Solder
610140109
Coax Contact
For vertical PCB terminations. Used with standard 50 and 120 Pin Micro Coax Modules.Up to 10GHz transmission speeds (PCB design dependent). Two-piece contact that allows for pin replacement, field repairable. Mates to all existing Micro Coax contacts.
-
Product
Ceramics and Glass Inspection Systems
-
Due to their special material properties, ceramic and glass components are the basis of many high-tech products. The same properties make the production complex and costly. Substrate defects that lead to failure of finished components should be avoided at all costs. For this reason, early automated optical inspection is essential.For the inspection of sapphire and quartz glass Intego has developed systems to detect both external and internal defects and can also provide cutting suggestions. Using index matching it is possible to test rough or uneven glass profiles.For the inspection of ceramic components Intego offers solutions specifically tailored to the respective testing task. Our modular design uses standard components that have already been developed and tested and in most cases only requires minimal adaptation.
-
Product
Test Targets & Charts
-
APPLIED IMAGE is a world leader in the field of IMAGE EVALUATION Test Targets and Test Charts. Some of the specialized test charts include camera image evaluation ISO, NIST, ANSI, and MIL standard image evaluation applications; photonic and optophotonic applications; test charts for copiers and scanner; DATAcapture and BARcode Scanning testing; Security & Identification Image Capture; and all other type of imaging industries that require quality evaluation of thier image capture systems.
-
Product
EZ-View Flow Meters
-
Hedland EZ-View flow meters provide a lower cost alternative to standard Hedland flow meters. Made from high-impact thermoplastics like polysulfone and Radel, these variable area meters (rotameters) contain a minimum number of moving parts, offering a reliable, trouble-free flow rate indicator. Fittings, available in brass, stainless steel and PVC, with NPT or BSP ports, allow the meter to be installed in a wide variety of applications. Meters can be used in oil and water processes, with the ability to add a flow switch, which can be used to trigger alarms.
-
Product
Facility & Asset Management System
Insight
-
Today’s environment confronts lab managers in new, challenging ways. The current regulations demand increasingly complex test procedures that require more time and resources to execute, which counteracts the goals to improve productivity and reduce costs. Therefore, lab managers need to maximize the test cell availability by continual awareness of the current situation in their facility. They must ensure the equipment is fully functional, meets all mandatory quality standards and regulations, and is up to date with all service and maintenance requirements.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - 3U VPX
Model 52760
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Basic Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Are ideal for current measurement in electrical systems and control cabinets, since only single wires are guided through the clamp jaws for contact-free current measurement and no electrical connections have to be disconnected. This method also enables measurements of very high currents, which would overload any standard multimeter if connected directly.
-
Product
Adapter Plate, 9050 Enclosure to 9025 ITA
410112422
Adapter Plate
This Adapter Plate allows a 25 Module ITA to accept standard 50 Module Enclosures.
