Product

High Voltage Optically Isolated Probe, 700 MHz Bandwidth. Includes soft-carrying case.

DL07-ISO

-

Teledyne LeCroy

DL07-ISO - Teledyne LeCroy

The DL-ISO enables highest confidence in GaN and SiC device characterization with highest accuracy, best signal fidelity, and comprehensive connectivity.

Product

Cryogenic Millimeter-Wave / Microwave Test Fixtures and Calibration Kits

upj10

-

KEYCOM Corp

upj10 - KEYCOM Corp

KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.

Product

Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-60V offset, +/-800mV

RP4060

-

Teledyne LeCroy

RP4060 - Teledyne LeCroy

+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).

Product

Test & Test Development for Circuit Card Assembly

-

Teledyne Defense Electronics

Teledyne Defense Electronics

Teledyne Advanced Electronic Solutions performs comprehensive testing at the CCA and system level assembly. Teledyne AES can perform testing developed by the customer or develop a complete test strategy for the customer’s products.- Bed of Nails FixtureIn-Circuit Test (Bed of Nails) or Flying Probe Testing for rapid feedback on CCAs- Functional testing of CCAs or complete systems- Environmental testing to include vibration, thermal cycling, HASS, etc.- CCA and system level test development- High frequency testing – currently to 40 GHz- High power system testing – currently to 4kW

Product

MOD MONITOR

TYPE HFX-1

-

National RF, Inc

TYPE HFX-1 - National RF, Inc

The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.

Product

Temperature and humidity duct probe

T3113

-

COMET SYSTEM, s.r.o.

T3113 - COMET SYSTEM, s.r.o.

Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.

Product

Osprey Probe Card

-

MPI Probe Card Technology

MPI Probe Card Technology

The Osprey probe card is MPI’s solution to demand for ever finer pitch. It is designed for smaller Al pad, and is ideal for tiny pitch application with peripheral and full array pattern. With precise alignment and better planarity control, Osprey can reach higher productivity by multi-DUT design.  The forming wire (FW) type needle produced with MPI’s own micro fabrication process not only delivers high-quality performance but also allows easy needle replacement and shortens maintaining cycle time.

Product

General Purpose Test Probes

-

Coda Systems Ltd.

Coda Systems Ltd.

Low profile, short travel test probes for restricted space applicationsApplications where long travel is not required such as thin film/hybrid circuits or bareboard PCB testingReplaceable test probe by use of a receptacle

Product

Triple Quadrupole Mass Spectrometry

Xevo TQ-XS

-

Waters Corporation

Xevo TQ-XS - Waters Corporation

Demands on analytical laboratories are changing and every laboratory needs to ensure it can keep pace with these changes. The Xevo® TQ-XS offers: *StepWave XS™ ion guide that provides increased sensitivity for challenging compounds. *Enhanced detection system with six orders of linear dynamic range to ensure sensitivity is accessible. *Tool-free probe design reduces the time taken for any routine maintenance and provides improved reproducibility between users.

Product

Injection Transformer

J2100A

-

PICOTEST Corp.

J2100A - PICOTEST Corp.

The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.

Product

Thickness Gauges

CMX

-

Dakota NDT

CMX - Dakota NDT

The CMX has all features of the MX & MMX gauges with a ton of advanced features. Measure material and coating thickness simultaneously, while still detecting pits & flaws in a single mode (PECT). Auto probe zero, auto probe recognition, auto temperature compensation are also included. Selectable Large Digits and B-Scan display options, up to 64 custom user definable setups, selectable transducer table for precision linearity, and material and coating calibration options are also available.

Product

Directional Hotwire Probe for Air Speed

AP471S1

-

Senseca

AP471S1 - Senseca

Directional hotwire probe to measure air speed in the range 0.1…40 m/s and air temperature in the range -25°C…+80°C.

Product

USB Hall Probes

-

MAGNET-PHYSIK Dr. Steingroever GmbH

MAGNET-PHYSIK Dr. Steingroever GmbH

The USB Hall probe is simply connected to a computer and operated using easy-to-understand software. No additional measuring device is required to measure the magnetic field strength. You can download the "USB Teslameter" software for Windows here. A Linux version is available from us on request.

Product

True RMS Clamp Meter w/ Pipe Clmap Adapter

DL489COMBO

-

UEi Test & Measurement Instruments

DL489COMBO - UEi Test & Measurement Instruments

True RMS Clamp meter and 2 ATTPC3 pipe clamp adapter, 2 ATT29 K-Type temperature probes

Product

Changeable Cassette

230352/1 – CMK-03

-

Columbia Elektronik AB

230352/1 – CMK-03 - Columbia Elektronik AB

Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.

Product

Interposers and Probes

-

Teledyne LeCroy

Teledyne LeCroy

The Summit product family includes a wide variety of Interposer systems, designed to reliably capture serial data traffic while minimizing perturbations in the serial data stream. Probes include interposers, which are designed to capture data traffic crossing the PCI Express card connector interface, and MidBus probes, which are designed to capture traffic flowing within a PCB.

Product

Refrigerant Leak Detector

900026

-

Sper Scientific

900026 - Sper Scientific

The rugged flexible probe has an LED light tip for illumination and the meter indicates low battery or sensor failure. Multi-colored LED lights indicate the level of leaks detected.

Product

Test Thorn Probe

CX-41

-

Shenzhen Chuangxin Instruments Co., Ltd.

CX-41 - Shenzhen Chuangxin Instruments Co., Ltd.

Test Thorn Probe For testing accessibility in appliances with visibly glowing heating elements.

Product

Bare Board Electrical Testing

ProbeMaster

-

PentaLogix

ProbeMaster - PentaLogix

ProbeMaster is the complete software solution to your shops needs in bare board electrical testing. ProbeMaster is PentaLogixs top-of-the-line software package that combines all of the power of the PentaLogix CAM and Fixturing packages with support for moving probe, Netlist Comparison and other robust features.

Product

Exchangeable Test Fixture

MA 2111/D/H/S-5

-

INGUN Prüfmittelbau GmbH

MA 2111/D/H/S-5 - INGUN Prüfmittelbau GmbH

Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 9,30 kg