Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
TX / RX Module
-
RF Lambda’s TX /RX modules include both a block upconverter and downconverter. They can include front end amplifiers for lower noise figure or power amplifiers for high output power of signal conditioning and image rejection as required.
-
Product
Scienlab Battery Test System – Module Level
SL1001A Series
Test System
The SL1001A and SL1006A Battery Test Systems – Module Level Series help you emulate sink and source for battery modules for automotive and industrial applications.
-
Product
PXI-2534, 256-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-34
Matrix Switch Module
256-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2534 is a high-density 8x32 PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring solid-state relays (SSRs), the PXI‑2534 offers unlimited mechanical lifetime and the ability to route 55 W simultaneously on all channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
MUX Module
AS 770
-
MUX Module is used for combining or separating wavelength in a wide wavelength range.- CATV Wavelength Range : 1540 ~ 1620 nm- Low Insertion Loss- PON Wavelength Range : 1260 ~ 1500 nm- High Isolation
-
Product
PXI 8 Slot BRIC 552x8 1-Pole (12 sub-cards)
40-560A-121-552X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 4-Slot BRIC Matrix, 92x8, 1-Pole (2 sub-cards)
40-560B-021-92X8
Matrix Switch Module
The 40-560B-021-92x8 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC 276x8 1-Pole (6 sub-cards)
40-560A-121-276X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 3Ω to 22.3MΩ
40-251-054
Programmable Resistor Modules
The 40-251-054 is a programmable resistor module with 2 channels which can be set between 3Ω and 22.3MΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
2-Channel DAQ Module
SMT-FMC311
-
Sundance Multiprocessor Technology Ltd.
The SMT-FMC311 includes a single TI ADC3244 device. This is a dual 14-bit ADC able to sample from 15 up to 125MSPS. It has a maximum power dissipation of 325mW (typically 233mW). SNR is typically around 72dBFS and SFDR around 90dBc.
-
Product
PXI Very High Density Multiplexer, 5-Channel, 32-Pole
40-675A-002-5/32
Multiplexer Module
The 40-675A-002-5/32 is a 5-channel, 32-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI 42x4 Matrix Module, 1-pole 2A 60W
40-505-001
Matrix Switch Module
This range of medium density PXI matrix modules (40-505 thru 509) are able to switch up to 2 Amps or 300VDC/250VAC and come in42x4, 32x6, 25x8, 18x12 and 14x16 options. The modules are designed for switching medium voltage and power signals. The user signal connection is via a robust 160-pin DIN 41612, 78-pin D-type or 50-pin D-Type connector that is fully supported by the wide range of our cable and connector accessories.
-
Product
ABex Terminal Module for JTAG Technologies JT 37x7 BSCAN Cards
ABex TM-JT37x7
-
The ABex TM-JT37x7 is an ABex terminal module for the JTAG Technologies Boundary Scan Controller PXI/PXIe JT 37×7. In combination with the JT 2147/ABex from JTAG Technologies it integrates the POD functionality into the module.In combination with the PXI/PXIe JT 37×7 and the JT 2147/ABex it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
Product
PXI 5W Programmable Resistor Module, 4-Channel, 1Ω to 31.5Ω
40-252-010
Programmable Resistor Modules
The 40-252-010 is a programmable resistor module with 4 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated Common, 3GHz, 50Ω, SMB
42-876A-002
Multiplexer Module
The 40-876A-002 (PXI) and 42-876A-002 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI 2A Multiplexer, 4-Bank, 4-Channel, 8-Pole
40-614C-009
Multiplexer Module
This 4-bank, 4-channel, 8 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Transition Module for 3U cPCI PMC Carrier
TCP030-TM
-
The TCP030-TM is a 3U Transition Module to be used with 3U cPCI PMC carrier like TEWS TCP27011R. It provides easy access to the PMC I/O lines of cPCI PMC carrier with back I/O.
-
Product
Signal, Module, Receiver, QuadraPaddle, iCon Series, 160 Position, loaded w/ Twin Female Contacts and Round Posts
510160122
Receiver Module
Fully Loaded with Twin Female Contacts and Round Posts (Adapter Pins) (p/n's 610138200 and 610138117).Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
Product
NI-9421 , 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
779136-01
Digital Module
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Coax, Module, Receiver, 20/26 GHz/75 Ohm HD, 90 Series, 32 Position, incl. strain relief
510104289
Receiver Module
Primary mating module 510108179.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
Q Travel mini
-
The Q.Travel-mini is based to the Q.raxx modules from Gantner Instruments. With one Controller (Q.gate) and three slots for sensor modules (Q.bloxx) a flexible system for all types of measurements is possible. All modules can be used in combination with each other. The different sensor modules are shown in the overview.
-
Product
Schottky Barrier Bridge Quads
-
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
Product
PXI 16x8 2-Pole 2A Matrix
40-518A-002
Matrix Switch Module
The 40-518A-002 is a 16x8 2-pole medium density matrix module and is designed for switching medium voltage/power signals in test applications where reed relays do not have sufficient rating. They are also suitable for telecoms applications where send and return signals need to be switched simultaneously.
-
Product
68-Pin VHDCI Male to 68-Pin VHDCI Male, 50 Ω, Shielded Digital Cable
781293-01
Digital Cable
The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
PXI 8 Slot BRIC Matrix, 2A 1-Pole 224x12, 7 Sub-cards
40-597A-107
Matrix Switch Module
The 40-597A-107 is a PXI 1-pole 224x12 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 200 VDC/210 VAC. The 40-597A BRIC modules are available in 2, 4 or 8-slot sizes to suit most high performance PXI matrix requirements, constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
Test Solution
Eye-BERT MicroX
-
The Eye-BERT MicroX is a compact, easy to use test solution offering high performance bit error rate testing at a fraction of the cost of competing solutions. The unit is offered in two speed grades including the X10 which operates up to 14.5Gbps, and the X30 which extends the data rate to 29Gbps. Its broad data rate capabilities and long test patterns make this unit suitable for testing nearly all optical SFP, SFP+, and SFP28 transceivers in production with just one unit. The real-time eye opening monitor and eye scanning capability can aid in troubleshooting by providing the operator with additional link quality information. Other features include Autonomous pattern detection, SFP diagnostic tools, and wavelength tuning (per transceiver capability). With a click of a button the Eye-BERT MicroX will automatically test an SFP module based on its advertised capabilities and generate a detailed test report complete with manufacturer, part number, serial number, date code, fiber type, link length, speed, and test results. The Unit is supplied with anti-skid bumpers and is small enough to be integrated into larger systems for dedicated link verification.
-
Product
High-Density Precision SMU Mainframe (4 Slots, 1U)
PZ2100A
Mainframe
The Keysight PZ2100A is the precision source / measure unit (SMU) mainframe that uncompromisingly and densely integrates 20 SMU channels into valuable 1U height, full width, rack space with flexible module options at their best performance. It supports a variety of resources such as the Keysight PZ2110A Precision SMU, PZ2120/21A High-Speed SMUs, and PZ2130/31A High Channel Density SMUs with multiple functions such as pulser and digitizer, as well as precise voltage / current sourcing and measuring to adapt to a wide range of application requirements. The PZ2100A has 4 slots and allows any mixed module configuration for flexible scalability.
-
Product
PXI-6233, 16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module
779620-01
Multifunction I/O
16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6233 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, sinking digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6233 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6233 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
Product
Adaptive Relay, Virtex-6 FPGA - 6U VPX
Model 58624
-
- Modifies 68 IF signals between input and output- Up to 80 MHz IF bandwidth- Four 200 MHz 16-bit A/Ds- Four 800 MHz 16-bit D/As- 68 DDCs and 68 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
PXI Express Board Virtex-5 ADC Module
SMT790
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
