Voltage Calibrators
An accurate voltage units of measure to facilitate comparison to and adjustment of instruments.
See Also: Voltage Sensors
-
Product
Bench Power Supply, Calibrated w/Data, Adjustable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2690 CAL D
-
The 72-2690 CAL D from Tenma is a single channel adjustable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has complete digital control, intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
-
Product
High Voltage Amplifier
WMA-100A
-
The WMA-100A model is our cost-effective, compact, general purpose high voltage amplifier. With its high quality and small form factor, it is the ideal choice for any experiment that requires an all-round, reliable high voltage amplifier. It can also be used as a stand-alone low noise high voltage power supply. Two WMA-100A amplifiers and a WMA-IB-HS phase inverter - buffer can be used to double the output voltage.
-
Product
Dielectric Withstanding Voltage Test
-
The dielectric withstanding voltage test (also called high-potential, over-potential voltage-breakdown, or dielectric-strength test) consists of the application of a voltage significantly higher than rated voltage for a specific time, between mutually insulated portions of a component part or between insulated portions and ground. This is used to prove that the component part can operate safely at its rated voltage and withstand momentary over-potentials due to switching, surges, and other similar phenomena.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-112-HI
Programmable Resistor Module
The 40-230-112-HI (PXI) and 42-230-112-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 122Ω with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
-
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
Product
DC Voltage & Current Data Logger
-
The Track-It™ DC Voltage and Current Data Loggers are two channel battery powered stand alone compact data loggers that record up to 32,000 samples each of DC Voltage or Current data. Units are available in 4 DC voltage ranges or for DC current. Simply plug the data logger into an available USB port on your PC and customize the settings or transfer data with the included Track-It Software program.
-
Product
Voltage Sag Generator
SKS-1120GTB
-
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
Product
NI-9205, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle
865683-01
-
NI-9205, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9205, cDAQ-9171, and cRIO-9940 includes the NI-9205 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the cRIO-9940 Backshell for strain relief and operator protection from high-voltage signals. The included NI-9205 features a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. Additionally, the NI-9205 provides up to 60 V of overvoltage protection between input channels and common, and it is rated for 1,000 Vrms transient overvoltage protection.
-
Product
Voltage Maintenance Program
VoltRef
-
VoltRef provides the power of automation formaintaining statistical control of the volt in yourlaboratory. This program controls a low thermalscanner and voltmeter to compare voltagestandards using the process recommended by NISTand other national laboratories.
-
Product
PXIe High Voltage Programmable Resistor Module, 1-Channel, D-Type Connector
42-230-130-HI
Programmable Resistor Module
The 40-230-130-HI (PXI) and 42-230-130-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 6.97kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
DSR 100 Series
-
DSR 100 Series systems provide complete, single-box solutions for immunity testing. They include a simple-to-use yet powerful standards waveform generator matched with an industry leading power supply technology and come with an extensive library of tests for many automotive and aviation standards.
-
Product
Calibration Executive Software
CalEasy Series
-
CalEasy is a full-featured, Calibration Executive software package that supports the verification and calibration of Marvin Test Solutions instruments. The software is intended for use by users that prefer to perform in-house calibration and verification for their Marvin Test Solutions instruments. By calibrating or verifying the instrument in-house, the time and cost associated with returning an instrument to Marvin Test Solutions for calibration service can be eliminated or reduced. CalEasy is also used internally by Marvin Test Solutions production to perform initial calibration and to recalibrate the instrument when received for service. This ensures that user and factory based calibration performance is similar. Depending on the specific instrument, standards instrumentation supported for calibration / verification includes a DMM, and a frequency standards module. Some modules require the use of matrix switch card.
-
Product
12 Pulse SCR Controlled High Voltage Power Supply
-
- 12 Pulse SCR Controlled Power Supply, P/N 19435PS- Input: 480 VAC, 300 Amps, 3 PH, 60 Hz- Output: 0 to 3000 VDC ± 10%, 80 Amps max adjustable with potentiometers, and 4/20 mA input signals from the PLC- Output voltage and current are provided as 4/20 mA signals to PLC- Contactor and overload relay are installed for protection- Power ON Light- Start / Stop capability- EPO capability- Manual voltage control and current limit- PLC interface- Output voltage and current are displayed on the voltmeter and ammeter.- A selector switch is used to select between manual Control or PLC Control- The customer is responsible for the PLC controller and PLC programming- Power enclosure, 68″H x 65″W x 44″D- Control enclosure: 20″H x 16″W x 9″D- Weight: 5000 lbs. approximately- All input/output connections are inside the enclosure
-
Product
Standard Voltage 9 Pin D-Type Cables - Connector to Unterminated for Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 9-pin D-type connector.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-12010A
-
High Power Pulse Instruments GmbH
The high-current TLP/HMM test system TLP-12010A offers advanced features intended for the characterization of semiconductor devices, discrete components, such as TVS, varistors, capacitors, gas tubes, circuits and systems in the high power time domain. It includes high current I-V characteristics inpulsed operation mode, turn-on/off transient characteristics of the device, breakdown effects, charge recovery effects e.g. reverse recovery, Safe-Operating-Area (SOA) and ESD measurements in general.
-
Product
Optical & RF Test Equipment Repair and Calibration
-
Custom Calibration Solutions, LLC
We are the only commercial repair lab in the country capable of fixing major problems with optical test equipment including OSA's, Tunable Lasers, Attenuators and Optical Wavelength meters.
-
Product
Voltage Probe
VOL-PBE
-
• EMI Receiver equipped with voltage probe can test disturbance voltage from load terminals or control terminals
-
Product
Standard Voltage 37 Pin D-Type Cables - Connector to Unterminated for Pickering
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.
-
Product
Low Voltage Power Supply Solutions
-
AC-DC Configurable. Advanced Energy is proud to offer highly reliable and cost-efficient low voltage power supply solutions. The Excelsys low voltage power supply product line has more than 20 years of experience of engineering power-density rich and extremely efficient supplies for a variety of markets.
-
Product
Voltage Input Module For Remote I/O
Module
The Voltage Input Module for Remote I/O features 2-, 3-, and 4-wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Voltage Input Module for Remote I/O from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements.
-
Product
Low Level, DC Voltage Data Logger
Volt101A
-
The Volt101A is one of MadgeTech's newest data loggers. It is part of a new series of low cost, state-of-the-art data logging devices. MadgeTech has taken the lead in offering the most advanced, low cost, battery powered data loggers in the world today.
-
Product
High Voltage Impulse Test Set Up
-
We are renowned as the foremost manufacturer and exporter of High Voltage Impulse Test Set Up. This testing equipment is demanded in electrical, power generation and engineering sector. It is incorporated with fiber optic isolated digitizers to test various types of transformers. We utilize excellent grade raw materials to engineer and develop this High Voltage Impulse Test Set Up in accordance with industry standards. Our clients can get this equipment from us at competitive price.
-
Product
Calibrated Leak Standards
-
LeakMaster is a leader in the industry when it comes to the manufacturing of calibrated leak standards (calibrated leak orifices). Each leak standard is meticulously manufactured to a specific leak or flow rate at a predetermined pressure. The purpose of each leak standard is to teach, or calibrate a leak test program, and allow the leak test instrument to memorize the characteristics of a leaking part. These leaks are also introduced into production parts to simulate a “leaking or failed” part condition. LeakMaster supplies a calibrated leak standard with every leak test instrument, and provides recertification services for all of their leak standards
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-233-HI
Programmable Resistor Module
The 40-230-233-HI (PXI) and 42-230-233-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 52.4kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Conformance Calibration Standard Test Card for GS1-DataBar Symbol Verifiers
AI-CCS-DATABAR
-
This test card is ideal for testing verifiers, scanners, and other GS1-DataBar barcode reading equipment. It also can serve as an excellent training aid to ensure new operators are using the proper methodology and are proven competent in the use of verifiers.
-
Product
PC Controlled High Voltage Tester
Cablescan H8
-
The Cablescan H8 provide the PC-based power of the larger PC based testers, but in an economical package for users who do not require more than 512 test points. This analyzer is designed to operate under the control of your PC.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-035-HI
Programmable Resistor Module
The 40-230-035-HI (PXI) and 42-230-035-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 201kΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Gauges & Calibrators
-
Ralston Instruments' gauges and calibrators are born from decades of experience working with technicians, project managers and facilities teams responsible for maintaining metrology instruments.
-
Product
Sound Level Calibrator
511E
-
Accepted internationally 1 kHz represents the "0 dB" reference point of A, B, C Weighting and other filters utilized in acoustic measurement. The Pistonphone - a mechanical sound source - offers a slightly higher degree of accuracy at a substantial increase in cost. In addition, the 200 or 250 Hz operating frequency is mechanically limited and not suited for measurements of filtered inputs. The 0.2 dB accuracy is quickly lost in the 0.7 to 1.5 dB tolerances acceptable for weighting filters at frequencies around 250 Hz.
-
Product
Voltage And Current Amplifier
KINGSINE KA30 / KA60
-
KINGSINE Electric Automation Co., Ltd.
KINGSINE's KA30 / KA60 voltage and current amplifier is high accuracy, high power, Panel-mounted type real time simulation power amplifier with four-phase voltage and three-phase current.
