-
Product
10G DPSK Demodulator
-
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5,10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systemsutilized in commercial, defense and space exploration markets. The device plays a key role in improvingsignal quality and performance to meet the expanding demand for higher data rates and more complextransmission formats within current and next generation systems without major capital expenditure.Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. The measured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarization-dependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
Product
Rack Mount, 1U, Switchable Dual 2x4/1x8, LL/UL/S Bands, Programmable Amplitude Balance
LS-16A-R1-24SLUS
-
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
Product
Pulse Acquisition Board
MS 1818
-
*Used to measure the amplitude of discrete pulses driving relay coils/motors*Programmable No. of samples acquisition with programmable trigger option*Converts sine wave to square wave for pulse measurement*Measures amplitude of sine wave*16 Bit ADC interface*16 Bit data bus host interface*FPGA based design with flexible configuration*1K FIFO Storage
-
Product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
-
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
-
Product
IQ Demodulator
-
Teledyne RF & Microwave IQ Demodulators are fully space-qualified designs providing stringent phase and amplitude matching, and superior output third order intercept performance. To meet high LO and IF rejection requirements diplexers are used at the I and Q ports. All components and processing fully meet MIL-PRF-38534, Class K and MIL-DTL-28837. Teledyne RF & Microwave can provide performance to meet most receiver system requirements, including single or moving LO frequencies and tight phase and amplitude matching. Customers can specify our designs for space, military, or commercial applications.
-
Product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, LL/S , Programmable Amplitude Balance
LS-16A-R1-24SLS
-
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
Product
QAM DVB Analyzer
-
Wuhan Sunma Technology Co., Ltd.
QAM Analyzer designed for both installation and maintenance of HFC system. Measure and display main parameters in DVB testing (channel power, MER, BER, Constellation Diagram), signal level on any frequency, amplitude of the carriers singly in the whole system range, and etc. The Analog, QAM and FM channel can be set and tested efficiently; it also supports HUM measurement, C/N measurement, voltmeter function, spectrum analysis and data logging. Also it is easy for user to obtain a report of test data via PC or printer through toolbox software.
-
Product
Real-Time Spectrum Analysis Software
S240
-
The ThinkRF S240 Real-Time Spectrum Analysis Software features a completely redesigned graphical user interface (GUI) from previous versions. Designed with the end-user in mind, the S240 keeps common setting such as Frequency, Bandwidth and Amplitude visible at all times, making it easy for the user to get the right view. All other settings and functions are available through an intuitive menu system that minimizes the number of clicks and the time it takes to find the right functions, while still keeping the view of the spectrum front and center. Customized settings can be saved and reloaded to simplify the setup of common applications and uses.
-
Product
HandyScope HS5: 50 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 5MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-055XM-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 50 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
Ultra Low-Loss Cable Assemblies
dB Miser
-
Cost-Effective, High-Performance Solutions for Low Loss ChallengesConsider dB Miser™ ultra low loss cable assemblies. High performance materials, careful attention to design detail, and stringent process control yields:- Ultra low insertion loss over the specified frequency range- Excellent amplitude stability with flexure- Stable performance over operating temperature range - Increased shielding effectiveness - Greater connector retention
-
Product
Single Channel High Voltage Linear Amplifier
F10A
-
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Vector Network Analyzers
-
One of the most important measurement tasks in radio engineering is the analysis of electrical circuits. A network analyzer is an instrument that is designed to solve this problem with high accuracy and efficiency. The circuits that can be analyzed with network analyzers have a wide range of applications ranging from simple devices such as filters and amplifiers to complex modules used in communications satellites. PLANAR specializes in the development and production of vector network analyzers that combine the capabilities of scalar network analyzers that measure not only the amplitude components of the main characteristics of the system (gain, loss, standing wave ratio, etc.), but also allow measurements of the amplitude and phase characteristics of the system .
-
Product
Amplifiers
-
Teledyne Lincoln Microwave design and manufacture RF amplifiers utilising the latest semiconductor technology. Our portfolio includes low noise amplifiers (LNA’s), power amplifiers and pre-amplifiers. These can incorporate linearization, filtering, phase and amplitude control functionality.
-
Product
Highly Shielded Phase Stable Assemblies
PhaseMaster® Enhanced
-
Does your application require cable assemblies offering some combination of phase stability and low loss, significant shielding effectiveness and increased durability?Consider Phase Master® 190E as your design-in option.Compared to similar phase stable cables, the Phase Master® 190E’s enhanced, multilayer shield construction yields:- A high level of phase stability vs. temperature- Reduced insertion loss & increased amplitude stability - Increased shielding effectiveness (120 dB @ 1 GHz, min)- Increased mechanical durability, especially torsion resistanceGreater connector retention (>40 lbs straight pull with SMA connectors)
-
Product
Non-Linear Pulse Amplifiers
-
These amplifiers have fixed output amplitudes, and are DC-coupled. All models can drive 50 Ohms or higher.
-
Product
Dual Channel Driver Card
40461
-
Two channels of 8 to 10 MHz drivers (25 V amplitude). The output voltage range is ±25V, with independent high and low voltage settings. The inputs to the Card are optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel as low as one nanosecond increments.
-
Product
HV Test bench
-
It is a deeply customizable test bench which is suitable to generate frequency and amplitude controlled voltage. This test bench could be used for life test or quality test on samples or devices. It can be configured both for sinusoidal test (STANDARD version) and both for square wave or pulse test (TechSQUARE). It includes safety systems for avoiding overload and incorrect use.
-
Product
Flicker Measuring Probe for LCM ATS
A712306
-
The Chroma A712306 Flicker Measuring Probe for LCM ATS is specifically designed for adjusting the flicker on LCM automatically following the FMA(Flicker Modulation Amplitude) standards defined by VESA (Video Electronics Standards Association) and JEITA (Japan Electronics Information Technology Industries Association) for flicker measurement.
-
Product
2 Channel 1GSPS 8 Bit ADC Card in FMC
FM582
-
Sundance Multiprocessor Technology Ltd.
The offset adjustment does not clip the signal at the highest range (+/- 5V). That is why the “max input signal amplitude” has been specified as 10V, even though the selection of signal ranges only goes up to 5V. This way, a +10V pulse with -5V offset could still be digitised without clipping.
-
Product
Coaxial Power Dividers
-
A coaxial 2-way power splitter with a typical insertion loss of 1.2 dB at each output port and a typical isolation of 16 dB across the frequency range of 1 to 18 GHz. The power splitter has a nominal power handling of 30 W (CW) and a typical amplitude unbalance of ±0.4 dB. The return loss for all ports is 13 dB typical. The RF connectors of the power splitter are female SMA connectors.
-
Product
Three-Phase Relay Test Equipment
AK-30
-
AC voltage source with 4 channels, current source and aux with 6 channels. DC source can be used simultaneously. Amplitude, frequency and phase angle can be adjusted respectively, independently and continuously; Control via PC via Ethernet RJ45 interface
-
Product
Low Noise Prepolarized Microphone
378A04
-
The 378A04 is a matched system that is comprised of a high sensitivity microphone and a low noise preamplifier that contains a built-in filter that enables the free-field response to remain flat over a wide frequency range. The system requires a minimum of 4 mA and measures to 6.5 dBA (5.5 dBA typical) within a cost efficient, prepolarized (0V) design. PCB's model 378A04, the industry's first prepolarized low noise microphone and preamplifier system allows you to measure extremely low amplitudes. In the past this was only possible with externally polarized solutions. With a typical noise floor of 5.5dBA, this microphone system delivers all of the benefits commonly associated with prepolarized systems.
-
Product
Function Generators
-
These models provide sine, square, triangular waveforms, with variable DC offsets. They may also be used as variable gain amplifiers. Gain and amplitude parameters can often be customized for special applications.
-
Product
Phasemeter
-
Moku:Phasemeter is based on a digital phase-locked loop architecture and can track the phase, frequency and amplitude of two signals from 1 kHz to 200 MHz. Measure phase changes of less than a millidegree with a sensitivity of better than 100 nanocycles/√Hz. Record frequency fluctuations with zero dead time.
-
Product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, LL/S/C , Programmable Amplitude Balance
LS-16A-R1-24SLSC
-
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
Product
Saluki S1433 Series Handheld Signal Generator (1MHz to max. 50GHz)
-
Saluki S1433 series signal generator is a hand-held instrument specially designed for field testing. It has the functions of CW signal output, FM/AM/Pulse modulation, large dynamic range amplitude adjustment, step/list sweep etc. The integrated design of 8.4-inch large capacitive touch screen is convenient for users’ operation.
-
Product
ECM Noise Under RF Test System
BK8020
-
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
-
Product
Power Dividers
-
Teledyne RF & Microwave offers several In-Phase Two-Way Power Dividers with high isolation, low insertion loss, excellent phase and amplitude balance in a small size for a variety of communications applications.
-
Product
Transmitters
-
Seismic transmitters provide a 4-20mA DC signal output proportional to the vibration amplitude, and are ideal for applications where a PLC, DCS, or other automation system will be used instead of a stand-alone vibration monitor. Metrix offers seismic transmitters with a wide variety operating temperatures, frequency responses, scale factors, case materials, connector types, mounting options, and hazardous area approvals.
