-
Product
Spectrum Monitoring and Interference Systems
-
Automate wide area, close-proximity signal monitoring, interference detection, identification, location, reportingIncrease flexibility; set up rugged, portable-RF sensors in fixed, temporary or mobile platforms in any environment for extended periods of timeRemotely deploy a single sensor or a network of sensors synchronously country or city-wide, or in a roomCustomize for your application with software for spectrum monitoring, emitter location, signal intercept, capture/analysis
-
Product
Interference Detection And Mitigation
-
Now more than ever, it’s critical to protect military systems from the threat of GNSSGlobal navigation satellite system (GNSS): A general term describing any satellite constellation that provides positioning, navigation, and timing (PNT) services on a global or regional basis. See also GPSGlobal Positioning System is a navigation satellite system. See also signal jamming and spoofing by using anti-jamming GPS and spoofing detection solutions.
-
Product
Interference Locating System
SeeWave®
-
Interference impacts wireless network coverage and quality of service, but hunting interference in the field can be expensive and time-consuming. PCTEL’s SeeWave® interference locating system enables a single user to accurately detect the interfering frequency and locate its exact source.
-
Product
Interference Modeling And Simulation
-
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
Product
Electromagnetic Interference Test
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
Interference Lithography Gratings
-
Interference lithography is an optical nanolithography technology for the fabrication of extensive periodic nanostructures. Critical dimensions of less than 50 nm can be realized. At AMO two interference lithography tools are installed. One setup for extensive, high quality gratings with fixed periods, the other more flexible tool allows quick prototyping. We offer grating fabrication on silicon, silicon dioxide and other substrates with tailored pitch, etch depth and size.
-
Product
Noise & Interference Generator
GPS7500
-
The programmable GPS7500 Noise & Interference Generator is capable of generating up to a 40 MHz wide noise or interference band for GPS receiver susceptibility testing.
-
Product
Interference & Compatibility Evaluation System
ICEy
-
Schmid & Partner Engineering AG
ICEy is the most advanced reactive near-field E/H-field scanning system for the analysis of EM interference and compatibility (EMI/EMC) in highly integrated electronics. ICEy is the only system that provides accurate EM measurements traceable to international calibration standards and also allows independent interlaboratory comparability of EMI/EMC measurement results.
-
Product
Linear Amplifiers
LA Series
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
UltraTEV Plus
-
The UltraTEV Plus is the latest innovation being introduced to the award winning UltraTEV range. This easy to use instrument incorporates additional sensing capabilities and real time advances analytical features enabling you to distinguish between true PD, noise and other interference allowing you to make better decisions while saving time and money and enhance the safety of your staff and your network.
-
Product
Power Line Meter
-
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
Product
PXIe-5667, 3.6 GHz PXI Vector Signal Analyzer
782366-03
-
PXIe, 3.6 GHz PXI Vector Signal Analyzer - The PXIe‑5667 is optimized for spectrum monitoring applications such as radio monitoring, interference detection, spectrum regulation, and related applications in line with ITU recommendations. It features real-time signal analysis and advanced signal processing using the capabilities of the built-in FPGA. Additionally, the PXIe‑5667 includes options for various frequency ranges and instantaneous bandwidth.
-
Product
Spectrum Monitoring and Interference Detection Software
-
Supports multiple users; Compartmentalization between profiles; Allows real-time monitoring and generates SMTP alarm traps; Displays a large number of carriers (100+) Numerous RF calculations and monitoring settings; Waterfall Display; Spectrogram Display; OCBW, ACPR, 3dB Bandwidth; Min/Max, Channel Power; Up Time Report; All Major Browsers Supported
-
-
Product
Universal PD & EMI analyzer
Spark P3
-
Doble Spark P3 is a universal partial discharge (PD) and electromagnetic interference (EMI) analyzer that uses a software defined radio signal detector to identify characteristics of insulation system deterioration that could lead to the failure of high voltage equipment. It detects signals from suitable sensors in a frequency range between 9 kHz to 2 GHz for PD and EMI, and DC to 500k Hz for acoustic and reference voltage measurements.
-
Product
Fast Tuned Notch Filter
ES005 & ES006
-
Teledyne Defence & Space’s (TDS) range of Fast Tuned Notch Filters (FTNF) have been designed to protect Electronic Support Measures (ESM) receivers from high duty cycle, frequency agile interference produced by on board (or cohort) combat radar systems. ESM sensors often need protection from high power nearby radars, and such signals can reduce receiver dynamic range.
-
Product
Artificial Power Network
KH3765
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH3765 artificial power supply network is equipped with the receiver produced by our company to conduct large current conduction interference test. The frequency range of this product is 150KHz-30MHz , the current is 50A , and the AC frequency can reach 0-400Hz . It is widely used and convenient to switch. Compared with similar products on the market, it greatly reduces the operation steps and buys valuable time for your rectification work. This product also provides a standard10AThe interface makes your test more convenient. Meet the requirements of GB-6113 for power supply network.
-
Product
Spectral Sensing
-
The ams multi-spectral sensing family includes a broad array of spectral sensing devices providing between 6 and 18 channels in the visible and near-infrared spectrum. All products feature CMOS interference filters and benefit from innovative factory calibration to deliver precise spectral characteristics over their lifetime. Most include direct LED drivers to synchronize and control light sources for efficient digital shutter operations.
-
Product
4-20mA Output Inclinometer
LCF-2330
-
The LCF-2330 inclinometer series now includes a 4-20mA output signal option for applications that require long cable runs. This dual axis tilt sensor is fluid damped to minimize noise and vibration interference while also offering a sharp 1 µradian resolution. An internal temperature sensor is available and dual supply, ± 5 Vdc output is an option. The LCF-2330 is an excellent solution for rugged applications such as radar & antenna leveling, weapons platform leveling, barge and offshore platform control, deviation surveys, 2-axis machine tool leveling, bridge structural monitoring, submersible control feedback, offshore platform stability and manufacturing process equipment for the aerospace industry.
-
Product
Miller 400A
44500
-
Rugged, lightweight case - safe to use on wet ground. Weatherproof, even with lid removed - IP67 rating for dust and water intrusion. Convenient case lid removal for ease of movement, with test leads attached, to new measurement locations. Resistance measurement range from 0.01Ω to 1.1MΩ . Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 97Hz (the unit’s operating frequency). Runs on a set of C-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source
-
Product
Optical signal transmission
Digital
-
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
Product
Tunable Diode Laser
-
Tunable diode laser absorption spectroscopy (TDLAS) is a fast, accurate, non-contact gas analysis technique that responds quickly to changing analyte concentrations. It is a proven technology free of interferences from other sample stream components.
-
Product
EMI/EMC Testing
-
This type of testing is required for devices, systems, and applications within the military and aerospace industries. Weapons, aircraft, ground and support equipment, electrical, and electronic systems must meet the established requirements.During electromagnetic interference the component's electrical circuit is affected due to either electromagnetic conduction or electromagnetic radiation from an external source.
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF2 set
-
The RF2 near field probe set consists of 4 passive near field probes for measurements in the development phase of the magnetic field in the range from 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF2 set allow the step by step localization of interference sources of the RF magnetic field on assemblies. From greater distances the electromagnetic interference can be detected by RF-R 400-1 and RF-R 50-1 probes. The RF-B 3-2 and RF-U 5-2 probes with their higher resolution can more precisely detect the interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Active Dual Loop Antenna
KH30936
-
Beijing KeHuan Century EMC Technology Co,.LTD
KH30936 active dual loop antenna is used for adjusting, testing, measuring and other receivers. It has many advantages:1. The antenna coverage frequency is wide: 150KHz ~ 30MHz .2. The field strength value is measured according to the correction coefficient within the effective frequency range, which is convenient to use.3. The antenna power is supplied by the host, which is convenient for outdoor measurement.4. Compared with the single loop antenna, the advantage is to read the maximum value directly, which eliminates the tedious steps of rotating the antenna to find the maximum value and the interference of the human body to the signal.
-
Product
GPS Simulator
MVT-NSSG
-
The Navigation Spread Spectrum Generator can be used for precise GPS M-Code interference tests with existing GPS C/A and P/Y receivers. The simulator is capable of generating all the current GPS signals simultaneously with the new modernized signals and codes. Optional models can be configured with unique user defined signals, such as would be required for GLONASS.
-
Product
Receiver, ICon EMI , With Protective Cover And Strain Relief
310123102
-
Includes all of the standard features of the iCon, in addition to Electro-Magnetic Interference (EMI) protection. An earth ground terminal is included on the and a "mate first, break last" feature connects the earth ground circuit. The earth ground terminal on the strain relief prevents user shock and injury.
-
Product
DC Blocks
-
Coaxial components that prevent the flow of audio and direct current (DC) frequencies while offering minimum interference to RF signals.
-
Product
IR Carbon and Sulphur Analyzer
LD-LCSA-A12
-
IR Carbon and Sulphur Analyzer LCSA–A12 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 25 to 60 seconds and 10 to 30 °C, the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 32-bit sampling improves sensitivity and accuracy.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
