Ultrasonic Flaw Detectors
See Also: Flaw Detectors
-
Product
Combustible Gas Detectors
-
A leak of natural gas (methane), propane or butane can cause an explosion in a basement with a sloppily installed unit as easily as it can in a coal mine. General sells these life-saving combustible gas detectors in various shapes and sizes, including pens and wands with a probe. Two models, the NGD268 & PNGD170 Combustible Gas Detectors even work from -40 to 158F, the extreme environment typical of mines and tunnel construction.
-
Product
Ultrasonic Liquid Level Difference Meter
HR9100L
-
HighReach Measuring & Controlling System Co.,Ltd
1. Stable and reliable / We select high-quality modules and key components from the power supply part to select high-stability and reliable devices, which can directly initiate imported instruments. 2, patented technology / one ring patented sound wave intelligent technology software can Carry out intelligent echo analysis without any debugging and other special steps, this technology has the function of dynamic thinking, dynamic analysis 3, high precision / sound wave intelligence owned by our company The patented technology makes the accuracy of TS-CJ ultrasonic level gauge greatly Improved, the liquid level precision reaches 0.3%, can resist various interference wavesThe instrument is a non-contact type. The meter does not directly contact the liquid, so the fault rate is lower. The meter provides a variety of installation methods, and The user can use this manual to calibrate the meter. 5. The protection level of multiple protection/instrument reaches IP65; all output and input lines have lightning protection and short circuit protection.
-
Product
General Purpose Acoustic Emissions Detector
BW-AED-500
-
The input can range from 40Hz to 160KHz from sensors with similar ranges. The output can be delivered to a speaker, oscilloscope and an LED for threshold detections ranging from 0-Infinite. The power supply features regulated +5VDC, -5VDC, +12VDC, +15VDC, -15VDC and +/- unregulated 20VDC. Voltage input of 110VAC @ 60Hz or 220VAC @ 50Hz.
-
Product
Fixed Gas Detectors
OLCT 10 - OLC 10
-
Teledyne Gas & Flame Detection
The OLC 10 and OLCT 10 are designed to detect combustible or toxic gases for tertiary applications (boiler plants, battery charging rooms, car parks, hospitals). Two OLC 10's can be connected to one detection channel to monitor the same area, without an additional junction box or extra wiring. Similarly, up to five OLCT 10's can be connected to one channel for the detection of CO, NO or NO₂ in a car park application. Easy to install and operate, these detectors combined with the MX 16 control unit meet demanding user requirements.
-
Product
Hybrid Picosecond Photon Detectors
HPPD Series
-
technology.The HPPD is our latest development in TCSPC detector technology that combines the benefits of conventional PMT design (wide spectral response and large active area)with the advantages of solid state APD technology (good detection efficiency, negligible after-pulsing and exceptional temporal resolution). Hybrid detectors are becoming thefirst choice for FLIM and short lifetime determination.
-
Product
Phantom Laboratory/QA Metal Detector
-
The portable and compact Phantom Laboratory Metal Detector is used offline to further examine rejected product from an in-line Large Bag or Gravity detection system. The Lab unit enables you to quickly filter out the metal contaminants and reclaim good product. Additionally, by isolating the contaminant QA can then determine the source of the problem and initiate corrective action. Equipped with a floor stand and castors, the Laboratory detector is easy to move from room-to-room. The ergonomically designed hopper offers a user-friendly means of hand-feeding product through its plastic pipe section. Two bins for Good product and Rejected product are also included with the system.
-
Product
Interceptor Metal Detector
-
Interceptor metal detectors are custom manufactured to achieve superior results in challenging applications. The Interceptor uses a simultaneous multi-frequency operation that effectively processes the transmission and reception of multiple frequencies continuously over a broad spectrum. This revolutionary operation facilitates an improvement in detection capabilities of up to 100% with stainless steel, especially when inspecting traditionally difficult “wet” products.
-
Product
Volcanic Ash Detector
-
Accurate measurements of atmospheric content for Volcanic Ash MonitoringVertical or 3D
-
Product
Leak And Seal Strength Detector
LSD-02
-
Jinan Leading Instruments Co., Ltd.
LSD-02 Leakand Seal Strength Detector is applicable in the quantitative measurement of leak, heat seal strength, heat seal quality, and burst pressure of each heat sealedges of the flexible packages that are made using heat seal and adhesiveprocessing, as well as sterilized packages; the quantitative measurement ofleak performances of all kinds of plastic pilfer-proof closures; thequantitative measurement of the unitary airproof, compression resistancestrength, cap body joint strength, cap disengaging strength, seal strength ofedge and butting strength of various flexible tubes. It can also provideevaluation and analysis for the compression and burst resistance strength ofthe materials of flexible packaging bags, the torsional airproof index of cap,the cap joint and disengaging strength and the stress strength; as well as theairproof performances, the compression resistance performance and the burstresistance character of unitary bottle, etc.
-
Product
X-Ray Detector
XRT Detector Onyx
-
ONYX 1412-X is a performance-leading X-ray detector comprising a proprietary 2768 × 2376 active pixel sensor array of 50 × 50 µm pixels. This detector consists of a high-speed, low-noise, radiation-tolerant, 14 × 12 cm, 6.6M pixel CMOS image sensor, with a directly deposited high-resolution CsI scintillator on Fibre Optic Plate. The highly configurable sensor is accessed through a software interface, connected via a 10 GbE SFP+ hardware interface.
-
Product
Torque Detectors
RH series
-
High rigidity: highly accurate detection of torque fluctuation with high response. The RH series is a torque detector that can accurately detect torque fluctuations with high torsional rigidity about 4.5 times compared to the existing products.
-
Product
Modular Linear Detector Arrays
X-Scan M
-
X-Scan M series makes quick and accurate inspection of large-scale objects easy. The modular linear detector arrays are scalable to different inspection system lengths up to 4.1 meters with one controller and single Gigabit Ethernet interface. With network connected units even longer scanners can be built efficiently for high-energy applications.
-
Product
IR Portable Gas Detector
Shipsurveyor
-
Teledyne Gas & Flame Detection
The Shipsurveyor was designed after extensive consultation with shipowners, ship managers and shipping personnel. The result is a range of 8 instruments dedicated to the marine market.The Shipsurveyor is versatile yet simple to use. The feature-rich range of instruments are suitable for all marine applications including confined space monitoring, cargo monitoring and inerting.Up to 5 gases can be simultaneously measured and displayed. The hydrocarbon range, which utilises the latest infrared technology, can be calibrated with Butane, Propane or Methane, depending on application.The Shipsurveyor also comes complete with an impressive and practical suite of application software. Our bespoke software not only allows simple on-board calibration but crucially provides the ability to print calibration certificates. In addition, complete datalogging software comes as standard allowing logged gas readings, with vessel locations, to be uploaded to a PC.With ATEX and MED approval, the Shipsurveyor is the complete shipping solution.
-
Product
Thermal Neutron Detector
TN15
-
The TN15 high sensitivity thermal neutron detector utilizes a state-of-the-art silicon photomultiplier (SiPM) and offers world-leading specification in a compact form. The TN15 surpasses the performance of a 100mm long 13mm3 He tube at 4 atmospheres and does not need cooling but operates at room temperature.
-
Product
Digital Voltage Detector
V-550
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Digital display for detected voltage with beeper sound.Can display AC voltage value by touting the insulation cover of conductor. (Approximate value)Accurate measurements for the bare terminal.Data hold and auto power off function.
-
Product
Wheel Play Detectors
-
A play detector consists of two plate units on which the wheels of an axle are placed. The plates are moved horizontally in an oscillating fashion by hydraulic cylinders. This movement can be done in different directions. In this way an inspector in the inspection pit can easily check for play on the different components underneath the vehicle. To make it even easier, the remote control unit to start and stop the plate movement has a built-in lamp.
-
Product
Wire Rope Detector
-
It adopts the method of magnetic flux leakage and magnetic flux, and uses the Ethernet high-speed transmission method, which can accurately complete the non-destructive testing of the wire rope in service.
-
Product
Thin Film Based Thermopile Detector: 1 Channel
DR46 Compensated
-
A one-channel compensated thin-film thermopile in a TO-8 package. The active area and compensating element area are 4mm x 0.6mm each. Offers high output with very good signal-to-noise ratio. Internal aperture minimizes channel-to-channel crosstalk increasing sensitivity.
-
Product
Specialty Coating Detectors
-
This NEW dual-purpose detector combines two instruments into one. Use the same device to identify the coated surface of glass for either the ShowerGuard or DiamondGuard coatings available from Guardian Industries.
-
Product
Semi-Automatic Contactless Wafer Detector
NCS-200SA
-
Semi-Automatically, non-contact measurement of wafer thickness, TTV ,bow,Point and flatness.Portable and easy to set-up, the Proforma 300/G measures all wafer materials including Silicon, Gallium-Arsenide, Indium-Phosphide and wafers mounted to sapphire or tape.the powerful software can test all the data above within several seconds,all the design according to SEMI standard and the ASTM,make sure the data can be easily unify. the system can used for several sample size,like 75 mm, 100 mm, 125 mm, 150 mm, 200 mm
-
Product
Ultrasonic Sensors
-
Leuze electronic GmbH + Co. KG
Ultrasonic sensors are used whenever optical systems reach their limits. Hence, partially and fully transparent or extremely dark objects can be detected just as easily as objects with reflecting surfaces or objects in dusty, vaporous or humid environments.
-
Product
Integrated Ultrasonic Level Gauge
HR9100T
-
HighReach Measuring & Controlling System Co.,Ltd
The circuit design selects high-quality power module components from the power supply part to select high-stability and reliable devices, which can completely replace the same type of imported instruments. The patented sonic intelligent technology software can perform intelligent echo analysis the debugging and the any OTHER Special the without Steps. This Technology has Dynamic Thinking at The Functions of the Analysis and Dynamic. Sound Wave at The Patented Technology of Our Company Makes at The Accuracy of at The Instrument Greatly Improved, at The Precision Liquid Level Reaches 0.25%, and IT CAN Resist various kinds of interference waves. This instrument is a kind of non-contact instrument, which does not directly contact with liquid., the instrument has a variety of installation methods. The user can use this manual to calibrate the instrument. All input and output lines Of the instrument have lightning protection and short circuit protection.
-
Product
Integrated Multi-Gas Detector for Unmanned Aerial System
MUVE C360
-
The FLIR MUVE™C360 is a multi-gas detector completely integrated with an unmanned aerial system (UAS) to provide real-time continuous monitoring of chemical hazards while on the move. The sensor block boasts 8-channels, which includes a photoionization detector (PID), Lower Explosive Limit (LEL) detector, and six other sensors. The integrated snorkel is designed to negate the effects of rotor wash, extending past the propellers to sample the unperturbed air. The MUVE C360 sensor block quickly latches to a proprietary integration dock mounted to the UAS. The FLIR calibration station features the same dock, so the operator can easily connect for routine sensor verification. Sensor readouts are prioritized based on alarm conditions and are displayed real-time on the pilot’s interface in the FLIR VueLink™ app. The MUVE C360 is a time-saving, game-changer for emergency responders, industrial safety officers, and environmental monitoring experts.
-
Product
Current Detectors
-
On our website you will find current detectors that are ideal for measuring AC or DC voltage. Current detectors are irreplaceable for inspection work and maintenance. We offer the following: voltage detectors, voltage leak detectors, voltage power detectors, Current clamps ideal for measuring AC or DC voltage. metric detectors, current detectors and more. These high quality current detectors include the capacity to measure many other parameters, such as capacity, resistance, power (both by way of clamps or by means of a hand held digital device with external clamps with a range of one or three stages). The current detectors are like the majority of our measurement instruments in that they meet and excel ISO standards. This calibration is done in a laboratory and comes with an accompanying certificate. All of our current detectors can perform the demanding tasks in each industrial sector regardless of the technical problem you encounter. If you can't find the current detectors you are looking for, please contact us and we will help you find the best solution to suit your needs by calling our offices on: UK customers +44(0) 23 809 870 30 / US customers (561) 320-9162 and our technical staff will advise you regarding our measuring instruments. Our engineers and technicians will be happy to help you with the current
-
Product
Gas Detectors
-
Great for HVAC professionals, Klein Tools’ Gas Detectors provide quick and accurate results. Whether you need to detect and measure concentration levels of CO and temperature, refrigerant gases, methane, propane, and other combustible gases, you can expect performance and durability from Klein.
-
Product
Wireless Gas Detector
OLCT 80W
-
Teledyne Gas & Flame Detection
Teledyne Gas and Flame Detection is proud to introduce its wireless system with the OLCT 80 field detector/transmitter. This new model allows wireless connectivity in ATEX 1 zones. The maximum range is 3km, line of sight. The type of network selected will depend on the number of field detectors, the area coverage and the network architecture.
-
Product
Phase Detector
Paula
-
BAUR paula phase detector. The paula phase detector is used for clear phase identification in earthed and shorted medium and high-voltage cables. With the help of the measurement procedure tried and tested over many years, paula delivers precise phase allocation without scope for interpretation and corresponds to the highest safety standards for tasks on and close to electric equipment.* Clear phase determination possible in cable lengths up to 40 km* Highest level of safety when used on earthed and shorted cables in compliance with EN 50110-1 (DIN VDE 0105-100)* Suitable for all switchgear constructions due to compact design of the signal injectors* Ready for operation for up to 2 weeks (standby mode)
-
Product
Laser Scanning Oil Film Detector
LO-300
-
LO-300 provides early warning by on-line detection of oil leakage with a laser and a security camera (option)LO-300 uses a laser to scan water surface or the ground to detect an oil film with high sensitivity.LO-300 with camera unit (option) enables to record the video when LO-300 detects the alarm and stores the image captured before and after alarm signal.
-
Product
Integral Explosive-proof Intelligent Flame Detector
FSE-100
-
FSE-100 Explosion-proof Flame Detector is used to collect the flame signal which is amplified and processed to determine the presence or absence of flame. FS-100 Flame Detector provides the flame output in real-time – the basis of determining the presence or absence of flame.
-
Product
Ultrasonic Thickness Gauges
-
A widely used nondestructive test technique for measuring the thickness of a material from one side. It is fast, reliable, and versatile, and unlike a micrometer or caliper it requires access to only one side of the test piece.
