Voltage Standards
-
Product
Standard Directional Gyroscopes
4000B-series
-
The 4000B is our standard air-driven directional gyro. As the aircraft turns left or right, gears on the sensing unit and dial shaft translate this rotation into rotation of the instrument’s vertical dial. Left turns produce clockwise dial rotation and right turns produce counter-clockwise rotation. The gyro is controlled by a heading selector knob located on the lower left of the instrument. Pressing and turning the knob first disengages the dial shaft and then resets the dial to a new heading, which results in a new course indication. Releasing the selector knob re-engages the dial shaft. The on-course position of the pointer is always at the top of the azimuth circle (0° on the dial with the aircraft headed north).
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 1 Channel, High Voltage Outputs
M2P.6570-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 4-Channel, 1-Pole
42-321-100-HI
Multiplexer Module
The 40-321-100-HI (PXI) and 42-321-100-HI (PXIe) are dual 4-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
High Voltage (Hipot) Cable Tester
CH2
-
The easy-wire CH2 was designed for commercial, military, and aerospace applications. Running on powerful Windows-based software, the CH2 offers unrivaled testing capabilities at an unparalleled price. Compact, easy-to-use, and FAST (shorts/mis-wires detected in <1 sec for 20,000 points), the CH2 is positioned to become the ''''tester of choice'''' for high-end users.
-
Product
High Voltage Insulating Diagnosis Systems
DAC-6017
-
It can measure and diagnose the insulating characteristic of winding coils of high voltage electric motor, generator, and etc.It also makes possible to build in-vehicle type or stationary type in accordance with the application.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-256-HI
Programmable Resistor Module
The 40-230-256-HI (PXI) and 42-230-256-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 76.8MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-704-HI
Multiplexer Module
The 65-231-704-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 7 kV. Multiplexers are created by populating the 65-200-002 scalable chassis with multiplexer plug-in modules that provide access to the Channel and Common signals on 51-pin front panel connectors.
-
Product
Charger and Low Voltage Power Supply
FlexiCharge FC1500
-
The FC1500 Medical Capacitor Charging power supply, with a built in configurable ACDC power supply is designed to provide the system power needs for Medical laser applications. The FC1500 can provide both capacitor charging and ACDC low voltage system power due to it’s unique design and intelligent control. The FC1500 can be used as a standalone capacitor charger, and if needed, various low voltage modules can be added to the unit to provide further system power. This functionality provides extra flexibility to power other systems and applications. Low voltage modules can be connected in parallel and in series for application that require higher voltage and current requirements. The Capacitor charger capabilities has the highest level of performance due the unique built in intelligent control for capacitor charging, higher charge rates and power limit control.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-241-HI
Programmable Resistor Module
The 40-230-241-HI (PXI) and 42-230-241-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 102kΩ with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
LXI High Voltage Switching - 2-Bank, 1-Pole, 24:1 Multiplexer Plugin Module
65-231-903
Multiplexer Module
The 65-231-903 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-214-HI
Programmable Resistor Module
The 40-230-214-HI (PXI) and 42-230-214-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 470Ω with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-H180-1
Switch Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-333-HI
Programmable Resistor Module
The 40-230-333-HI (PXI) and 42-230-333-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 52.4kΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-054-HI
Programmable Resistor Module
The 40-230-054-HI (PXI) and 42-230-054-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 22.05MΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Voltage Control Attenuator
-
RF Lambda’s voltage control attenuators allow for precision control of RF signals. With a voltage variable control pin the signal can be fine-tuned as needed by the system. These attenuators offer fast response time and wide band operation. Hermetically sealed options are available upon request.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-016-HI
Programmable Resistor Module
The 40-230-016-HI (PXI) and 42-230-016-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 1.8kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-125-HI
Programmable Resistor Module
The 40-230-125-HI (PXI) and 42-230-125-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 13.6kΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-909-HI
Multiplexer Module
The 65-231-909-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-026-HI
Programmable Resistor Module
The 40-230-026-HI (PXI) and 42-230-026-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 26.7kΩ with 8Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Voltage Datalogger
S5011
-
Data logger is designed for record of voltage. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper adapter.
-
Product
Standard Digitizer
725S Family
-
The 725S family is a digitizer capable of recording waveforms along with performing advanced algorithms for online digital pulse processing (DPP). Utilizing DPP Firmware, users can acquire quantitative physical parameters (Integrated Charge, Pulse Shape Discrimination with very fine time resolution, Pulse Height Analysis) as well as read out waveforms with automatic pulse identification and baseline suppression on channel basis (Zero-Length Encoding and Dynamic Acquisition Window). The wide range of DPP algorithms supported by the 725S make it a “must-have” for any type of nuclear physics application.
-
Product
High Collector To Emitter Voltage
-
High collector-to-emitter voltage photocouplers (optocouplers) are optically coupled isolators containing a GaAs infrared light emitting diode and an NPN silicon Darlington connected phototransistor. The isolation voltage during input and output and the voltage between the collector and the emitter of the transistor are both high.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-010-HI
Programmable Resistor Module
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI High Voltage Amplifiers
-
Pickering's PXI High Voltage Amplifiers are ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suit the user’s wiring system.
-
Product
Precision High Voltage Meter
4700
-
The Vitrek 4700 Precision High Voltage Meter offers the highest level of measurement accuracy when it comes to high-voltage measurement equipment. Its color touch screen is surprisingly easy to use for set up and display of testing results. Vitrek leverages DSP technology to provide outstanding AC &DC high voltage measurement accuracy, stability, repeatability and resolution. The 4700 High Voltage Meter offers performance that rivals traditional high voltage reference dividers – yet unlike the tedious divider, the 4700 provides instant, direct, high voltage measurements in a highly portable, compact and rugged bench top enclosure.
-
Product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Bias Ball Probe
POGO-1L-4-S
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
STANAG3910 Electrica lTest And Simulation Modulefor Standard Ethernet
ANET3910-EN
-
STANAG3910 Electrical Test and Simulation module for Standard Ethernet. The ANET embedded Linux operating system gives the unique capability to run the optional PBA.pro Engine right in the box.Another option is the ANET-ADK onboard software development kit where users create run-time applications to execute right in the box. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
Stand Alone Low Voltage Tester
TestMate 128
-
The TestMate continuity tester features a universal interface fixture that accommodates adapter cards for quick changes in harness setups. Adapters can be exchanged in seconds to adapt quickly to any of a variety of wire-harness/cable connectors.
-
Product
Standard Resistors for Temperature Measurement
-
Measurements International Ltd.
High Stability, Split Guard Circuit, Internal Temperature Sensor, Custom Values Available, Includes Calibration Data.
-
Product
Standard 1.02 (29.00) - 4.00 (114.00) High Performance Bias Ball Probe
POGO-62T1-4
ICT/FCT Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
