Non-contact Voltage Testers
check for presence of electricity.
-
Product
Current Transformer Testers
-
Vanguard Instruments Company, Inc.
Performs CT excitation, current-ratio, polarity, and phase angle testsMeasures insulation resistance and winding resistance of the CT seconday windingsMeasures the CT's secondary burdenTest record header information including company, substation name, circuit ID, manufacturer, CT serial number, operator name, and test record-commentsBuilt-in 4.5-inch wide thermal printerPlot Multiple Saturation CurvesStores up to 128 CT test plans and 140 test records internallyUSB, Bluetooth, and USB Flash drive interface
-
Product
EV Charging Station Tester
EV : ChargeCheck
-
The EV Industry’s Charging Station Tester of Choice. • Simulates an electric vehicle • Tests J1772 (type 1) tethered leads • Tests IEC62196 (type 2) sockets • Tests IEC61851-1 mode 3 communication compliance • Tests for correct polarity • Tests for earthing presence • Tests contactor actions.
-
Product
Ultrasonic Hardness Tester
-
Beijing TIME High Technology Ltd.
A non-destructive tool that measures the hardness of materials, particularly metals, by using ultrasonic vibrations.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-125-HI
-
The 40-230-125-HI (PXI) and 42-230-125-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 13.6kΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Multifunction Tester
COMBI521
-
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Tablet Hardness Tester
-
* Complied with USP* Pretty design with an easy operation* The model can be rotated 180 degrees position to do an error calibration.* Sample diameter range: Ø3 ~ Ø30 mm* The model can double as a tensile tester.* Pressure gauge with a variety of specifications to provide choice.
-
Product
High Voltage Test Sets
-
Nmc's high voltage test sets are manufactured as per the customers requirement ranging from 5kv-100kv ac or dc.
-
Product
NON-CONTACT TEST COMPATIBLE Ultra High Speed Bare Board Tester System(ALL-IN-ONE UNIT)
SX-750SUPERⅣC
-
All-in-one Compact Size TesterAll-in-One type Tester, with built-in PC in the Tester main unitImproved operability with a 10.4" Touch PanelAll the operation screens are optimized for touch-pannel operation.
-
Product
Linear Motor Tester Lite
BK2019B
-
With the BK2019B, you can test for open/short circuits, operating current and even vibration level. Because it has only one purpose, it is very easy to set up and use and it's so small it can fit into the average briefcase.
-
Product
Shore Hardness Testers
-
Measures the level of resistance a material demonstrates against indentation pressure.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-320-HI
-
The 40-230-320-HI (PXI) and 42-230-320-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3Ω and 472Ω with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
High Voltage Reed Relays from Pickering Electronics
-
Pickering Electronics' High Voltage Reed Relays are well suited for Instrumentation, Industrial Process Controls and General Purpose requirements. *Ideal for high-power applications*Plastic package with internal mu-metal magnetic screen*3V, 5V, 12V or 24V coils, diodes are optional*Dry instrument grade switches*Pickering's SoftCenter technology
-
Product
Folding Tester
FOT-01
-
Jinan Leading Instruments Co., Ltd.
FOT-01 Folding Testeris designed according to relevant standards and adopts modern mechanicalphilosophy and computer processing technology. Folding tester complies with relevant standard. It is suitable to test fatigue strength of paper, paperboardand other sheet material, which thickness is less than 1mm.
-
Product
Leeb Hardness Testers
-
It is a type of non-destructive testing used to inspect large sized workpieces weighing above 1 kg.
-
Product
Scorch Tester (Sublimation Fastness Tester)
TF415D
-
TESTEX Testing Equipment Systems Ltd.
Scorch Tester, to determine fabrics Ironing color fastness and sublimation color fastness, and dimensional stability under hot dry conditions. Sublimation Fastness Tester complies with ISO 105, BS 1006, AATCC 92/114/117/133. Sublimation machine price is reasonable.
-
Product
Digital Arrester Clamp Tester
ALCL-40
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*ALCL-40 is designed to test the diagnostic of OXIDE SURGE ARRESTER.*The least influence from the external magnetic field and noise by triple shielding of CT.*Compliant with IEC6099-5.*Enabled the measurements for 100nA resolution and harmonics current.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-153-HI
-
The 40-230-153-HI (PXI) and 42-230-153-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 11.32MΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-220-HI
-
The 40-230-220-HI (PXI) and 42-230-220-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 472Ω with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Akron Abrasion Tester
UI-FT45
-
Akron Abrasion Tester is used to test rubber abrasion resistance and it is suitable for rubbers with a hardsness in the range of 55-85IRHDx.
-
Product
Radio Frequency Cable Tester
RFCT
-
Textron Systems’ Radio Frequency Cable Tester (RFCT) allows for on-site testing and maintenance for radio frequency (RF) transmission paths within a platform. Using preconfigured databases of sweep parameters and pass/fail criteria, the RFCT quickly determines the status of installed RF cables. The RFCT checks each cable’s performance characteristics to include voltage standing wave ratio (VSWR), insertion loss (IL), phase and phase matching. If a cable fails a test, the RFCT automatically determines the distance-to-fault (DTF). With its intuitive touchscreen-based user interface and lightweight, ruggedized packaging, the RFCT is the gold standard for operational-level RF cable testing.
-
Product
Connector Board for Cable and Harness Tester
CB49
-
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors.
-
Product
Energized Tester
ALL-SAFE PRO
-
Conduct safe, easy and accurate ESA testing in only 60 seconds with the ALL-SAFE PRO® motor connection box. The ALL-SAFE PRO® is a permanently installed connection accessory for the ATPOL III™ energized testing instrument. With this electric motor connection box, the ATPOL III™ can perform tests easily with a quick disconnect.
-
Product
Flat-plate Thermal Conductivity Tester
-
TESTEX Testing Equipment Systems Ltd.
Flat-plate Thermal Conductivity Tester, to determine the thermal conductivity of various fabrics, quilting products, and other heat insulation materials.
-
Product
Battery Tester
G6606
-
Peaceful Thriving Enterprise Co Ltd
It can quickly test the capacity of your battery.
-
Product
Battery Impedance Tester
KVBT-15S
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Internal Resistance Tester with advanced AC discharge measurement method, is applied to test accurately the voltage and resistance of battery capacity and state.
-
Product
Mechanical Load Tester
-
Solar modules and collectors, whether on roofs, in façades, or freestanding, are often exposed to high mechanical stress or load: A deep layer of snow or strong winds can greatly affect the materials and connections. Mechanical load test stands accurately test the durability of PV modules and thermal solar collectors.
-
Product
Noise And Vibration Tester
-
In a miniaturized motor, even the slightest rumbling sound that occurs during rotation can be a cause for failure.
-
Product
Digital H.V. Insulation Tester(12kV)
7012 IN
-
Standard Electric Works Co., Ltd
● Protection class: IP66 (Lid closed)● Test insulation resistance up to 20TΩ (20000GΩ).● Short-circuit current up to 5mA● Microprocessor controlled.● 24 insulation test voltages : 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV, 10.5kV, 11kV, 11.5kV, 12kV ● AC/DC voltmeter (600V).● PI (Polarization Index) indication.● DAR (Dielectric Absorption ratio) indication.● Auto-ranging on all insulation ranges.● Backlight function.● Menu driven.● Visual and audible warning if external voltage is present. (≥30Vac or ≥30Vdc)● Auto-hold function to freeze the reading.● Overload protection.● Adjustment for testing time (duration) : ● 1~30 minutes● Auto-off.● Calendar.● Optical USB to RS-232 data transmission.● 200 measurement results can be saved in the memory and recalled on the display.● Safety standard : EN 61010-1 CAT IV 600V EN 61010-2-030 EN 61326-1
-
Product
Step & Repeat Non-Contact Inspection System for FPC and PCB
OHT-Ⅴ
-
*Space-saving design and highly efficient and high-speed inspection, with top and bottom slider structure*Roller head enables to handle the reverse imposition.*Easy operation by new alignment mechanism*The machine handlingPCB is called "WSR"
-
Product
Hipot Tester
NX Hipot+
-
50 to 1500VDC Hipot Testing, 50 to 1000VAC (optional), Expandable to 1024 test points, 5Mohm to 1Gohm Insulation Resistance, Simple 4-button user interface, Tests for continuity and shorts, Tests a variety of components, Precision resistance measurements, Continuous high speed scanning for real time complete status information of harness assembly progress, Keyed security access and control, Built for rough industrial environments, 2 serial ports for connection to printers and scanners, Standalone operation, Uses a high capacity memory card, Available from 64 to 1024 test points, Networkable
