Non-contact Voltage Testers
check for presence of electricity.
-
Product
Connector Board for Cable and Harness Tester
CB49
-
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors.
-
Product
Energized Tester
ALL-SAFE PRO
-
Conduct safe, easy and accurate ESA testing in only 60 seconds with the ALL-SAFE PRO® motor connection box. The ALL-SAFE PRO® is a permanently installed connection accessory for the ATPOL III™ energized testing instrument. With this electric motor connection box, the ATPOL III™ can perform tests easily with a quick disconnect.
-
Product
Flat-plate Thermal Conductivity Tester
-
TESTEX Testing Equipment Systems Ltd.
Flat-plate Thermal Conductivity Tester, to determine the thermal conductivity of various fabrics, quilting products, and other heat insulation materials.
-
Product
Battery Tester
G6606
-
Peaceful Thriving Enterprise Co Ltd
It can quickly test the capacity of your battery.
-
Product
Battery Impedance Tester
KVBT-15S
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Internal Resistance Tester with advanced AC discharge measurement method, is applied to test accurately the voltage and resistance of battery capacity and state.
-
Product
Mechanical Load Tester
-
Solar modules and collectors, whether on roofs, in façades, or freestanding, are often exposed to high mechanical stress or load: A deep layer of snow or strong winds can greatly affect the materials and connections. Mechanical load test stands accurately test the durability of PV modules and thermal solar collectors.
-
Product
Noise And Vibration Tester
-
In a miniaturized motor, even the slightest rumbling sound that occurs during rotation can be a cause for failure.
-
Product
Digital H.V. Insulation Tester(12kV)
7012 IN
-
Standard Electric Works Co., Ltd
● Protection class: IP66 (Lid closed)● Test insulation resistance up to 20TΩ (20000GΩ).● Short-circuit current up to 5mA● Microprocessor controlled.● 24 insulation test voltages : 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV, 10.5kV, 11kV, 11.5kV, 12kV ● AC/DC voltmeter (600V).● PI (Polarization Index) indication.● DAR (Dielectric Absorption ratio) indication.● Auto-ranging on all insulation ranges.● Backlight function.● Menu driven.● Visual and audible warning if external voltage is present. (≥30Vac or ≥30Vdc)● Auto-hold function to freeze the reading.● Overload protection.● Adjustment for testing time (duration) : ● 1~30 minutes● Auto-off.● Calendar.● Optical USB to RS-232 data transmission.● 200 measurement results can be saved in the memory and recalled on the display.● Safety standard : EN 61010-1 CAT IV 600V EN 61010-2-030 EN 61326-1
-
Product
Step & Repeat Non-Contact Inspection System for FPC and PCB
OHT-Ⅴ
-
*Space-saving design and highly efficient and high-speed inspection, with top and bottom slider structure*Roller head enables to handle the reverse imposition.*Easy operation by new alignment mechanism*The machine handlingPCB is called "WSR"
-
Product
Hipot Tester
NX Hipot+
-
50 to 1500VDC Hipot Testing, 50 to 1000VAC (optional), Expandable to 1024 test points, 5Mohm to 1Gohm Insulation Resistance, Simple 4-button user interface, Tests for continuity and shorts, Tests a variety of components, Precision resistance measurements, Continuous high speed scanning for real time complete status information of harness assembly progress, Keyed security access and control, Built for rough industrial environments, 2 serial ports for connection to printers and scanners, Standalone operation, Uses a high capacity memory card, Available from 64 to 1024 test points, Networkable
-
Product
Automated Discrete Semiconductor Tester (ATE)
5000E
-
Same Proven Technology as all 5000 Series Testers. High Speed Single Test Measure. Capable of Testing Multiple and Mixed Devices. 1KV Standard, 2KV Optional. 1NA to 50A Standard, 100A Optional. 0.1NA Resolution. Complete Self Test. Auto-Calibration. RDSON to 0.1MOHM Resolution. Windows Application Software. Optional Scanner. Optional Wafer Mapping. Optional Curve Trace. MOSFET, IGBT, J-FETTriac, SCR, Sidac, Diac, Quadrac, STS, SBS Transistor, Diode, Opto, Zener Regulator, MOV, Relay. UNDER $23,000.00
-
Product
General ELCB Testers
TEL1-x Series
-
Standard Electric Works Co., Ltd
The TEL1 is the Basic Test Equipment an Electrician cannot do without. TEL1 is a Dual Function Test Instrument utilized to Verify Electrical Wiring Connections and the Functioning of Earth Leakage / Residual Current Detectors devices by forcing the ELCB/RCD to trip.
-
Product
Reduced Voltage Motor Starting Panels by Reactors
-
A method to limit motor starting current is a series reactor. Iron core or air core reactors can be used for starting purposes. If an air core is used for the series reactor then a very efficient and reliable soft starter can be designed which is more suitable for high MW ratings of synchronous/induction motors at MV levels. The reactors are designed with taps.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-332-HI
-
The 40-230-332-HI (PXI) and 42-230-332-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 26.7kΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Digital (1kV below) Insulation Tester
2151 IN
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 68 × 34mm(2.677” × 1.338”) large LCD display.● 3½ digital LCD(2000 counts) a LCD indicated instrument for insulation.(MΩ), continuity(Ω) and AC voltage.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA DC load.● >200mA short circuit testing current for a resistance tests.● Auto ranging.● REL function.● Auto power OFF.● Fuse protection.● Auto data hold.● BS 16 edition.
-
Product
Blow Point Tester
EKT-2001BPT
-
The EKT-2001BPT Blow-Point Analyzer is a testing instrument that measures the best curing time of rubber for tire and rubber vibration isolation industry and helps to improve the productivity. By using the special design of wedge mold, it measures the real-time temperature rising during the curing to determine suitable curing time in the curing press.
-
Product
AATCC Wrinkle Recovery Tester
TF112
-
TESTEX Testing Equipment Systems Ltd.
AATCC Wrinkle Recovery Tester is used for determining a fabric’s ability to recover after wrinkling under a pre-determined load for a set period of time.
-
Product
Inductor Tester
-
An impulse can be applied to the coil of a chip power inductor to perform insulation tests (surge tests) within the windings.
-
Product
Oil Pour Point Tester
-
Weshine Electric Manufacturing Co., Ltd
WESHINE’s fully-integrated, automatic cloud and pour point apparatus(VS-9612 Cloud and Pour Point Tester) offers precise and convenient flow testing of petroleum products, biodiesel fuels, additives and lubricating oils.
-
Product
Drive Tester
Disk Manufacturing Module
-
SCSI Toolbox LLC is proud to announce the Disk Manufacturing Module, joining a decade of real-world drive testing experience with input from hundreds of customers to bring the best new testing tool to the disk manufacturing and integration marketplace.
-
Product
Hardness Tester
-
Jinan Testing Equipment IE Corporation
Hardness is the property of a material that enables it to resist plastic deformation, usually by permanent indentation. Indentation hardness measures the resistance of a sample to material deformation due to a constant compression load from a sharp object; they are primarily used in engineering and metallurgy fields. The tests work on the basic premise of measuring the critical dimensions of an indentation left by a specifically dimensioned and loaded indenter.
-
Product
Internal Resistance Testers
-
The Battery Internal Resistance Tester is essential for assessing the health and performance of stationary reserve power batteries. Designed for efficiency, this tester measures internal resistance, helping to identify potential issues before they impact battery performance. By providing accurate diagnostics, it enables proactive maintenance, ensuring reliability in critical applications. This advanced testing equipment is an invaluable tool for enhancing battery longevity and optimizing energy storage systems.
-
Product
Flying Probe Tester
FA1811
-
Designed specifically for package board testing, the FA1811 achieves both high-precision contact with a total probing precision of 10 μm, and a testing speed rivaling generic flying probe testers to meet ever increasing demands for greater analytical power, faster testing speeds and reduced costs.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-221-HI
-
The 40-230-221-HI (PXI) and 42-230-221-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 925Ω with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Automatic Insulation Oil Tester
KVIO-80
-
KV Hipot Power Test Equipment Co.,Ltd
Automatic Insulation Oil Breakdown Tester Is Used to carry on power frequency dielectric break down test on the transformer oil, capacitor oil, electric device, insulation tool etc.
-
Product
Bearing friction and wear tester
-
This testing machine evaluates the frictional characteristics of radial bearings. The circuit system adopted for the lubricant enables heating up to 80C.
-
Product
Dielectric Withstand Tester
-
Weshine Electric Manufacturing Co., Ltd
The induction withstand voltage test of transformers and transformers is an important test to ensure that the quality of transformers conforms to national standards. The longitudinal insulation induction withstand voltage test of the inter-turn, inter-layer, inter-section and inter-phase insulation of the transformer winding is an important item in the transformer insulation test.
-
Product
Film Tearing Strength Tester
DRK108C
-
Shandong Drick Instruments Co., Ltd.
DRK108C Tearing Tester is applicable in the tearing test of films, sheets, flexible PVC, PVDC, waterproof films, woven materials, polypropylene, polyester, paper, cardboard, textile and non-woven, etc.
-
Product
Low Level Voltage Measuring Instruments
-
This instrument has a very wide range of source resistance capability and has an equivalent noise resistance of less than 10 ohms. Sub-nanovolt resolution is possible. The N11 has many applications, including cryogenic measurements.
-
Product
110-125V AC GFCI Receptacle Tester
1934
-
Peaceful Thriving Enterprise Co Ltd
*With UL and cUL Approval.*Detect faulty wiring in 3 wire receptacle.*Test for GFCI receptacle for proper operation, 110-125V circuits.*Various combinations of three lights tell if wiring is correct or six possible faulty conditions.
