Discharge
-
Product
Leakage Test
-
Leakage current and discharge current depend on the insulation of the device. The measurement simulates various fault situations that could occur during operation. The test determines whether the measured current is within the permissible limits and poses no danger to the user in case of a fault.
-
Product
Shielded Bag Test Kit
PBT-531
-
The PBT-531 is a complete system kit designed to evaluate the performance of electrostatic discharge shielded bags and other packaging materials.
-
Product
Three Cups Insulation Oil Dielectric Strength Tester
STY Series
-
Chongqing Assen Power Equipment Co., Ltd
STY series three cups insulation oil dielectric strength tester uses a microprocessor to automatically complete boost, keep stirring, static discharge, calculate, print and other operations, is a necessary measure in the conventional test equipment.
-
Product
RC Meters
-
Provides the. capacitance to be measured at a frequency which is reciprocal to the. product of the discharge resistance and the measured capacitance.
-
Product
Battery Charger-Analyzer for small battery systems (up to 10A-Hr)
miniMasterCharger
-
The miniMasterCharger is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation of Constant Current Charge (dual and single rate), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge (analysis), Resistance Discharge (analysis) and Full Discharge (deep cycle), the miniMasterCharger can satisfy the requirements of most small (0 to 10 A-hr) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit (no load) and Overvoltage conditions.
-
Product
Battery Chargers
BAC Series
-
Battery charger BAC series is a portable and universal battery charging solution. It is primarily intended for charging Lead-Acid, Ni-Cd and Li-ion batteries from 1 V DC to 300V DC level. However, the unit can charge the string of any battery type by one of the available charge modes:IU (constant current + constant voltage)UU (constant voltage + constant voltage with a current limit)Charging modes provide a safe regulation of charging procedure and achieves fast recharge and low risk of overcharge.Variety of implemented protections, such as thermal, overcurrent, undervoltage, and overvoltage, assure the charging process will be safe for the battery and the instrument itself.A user doesn’t have to switch off the main charger in order to use BAC series charger. Just the opposite, the BAC series charger should support the main charger to speed up the process. An alternative use is to quickly recharge a battery following a discharge test.The provided display enables users to monitor all relevant information during the charging process and to adjust charging parameters and limits in real-time.The instrument offers the best power-to-weight ratio in the market, weighing only 10 kg / 22 lbs with the maximum output power of 2,7 kW.The maximum charging currents for lead-acid, Ni-Cd and Li-ion batteries, at various battery voltages, are presented in the brochure.
-
Product
BOD (Biochemical Oxygen Demand)
-
The role of Biochemical Oxygen Demand (BOD) is to measure the amount of oxygen needed to remove organic waste from the water of bacteria.Important to know, the larger the Biochemical Oxygen Demand, the more rapidly oxygen is depleted in the stream. This means there will be less oxygen in the water.biological oxygen demand is essential By providing information to assess the effect discharged wastewater will have on the receiving environment.The BOD value is commonly expressed in milligrams of oxygen consumed per liter of sample during 5 days of incubation at 20°C.The goal is maintaining the aquatic life and aesthetic quality of streams and lakes.
-
Product
Battery Tester
G5.BT
-
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
Product
Partial Discharge Inductor
Tracy
-
Cable testing and diagnostics with the BAUR tracy. The BAUR tracy partial discharge inductor induces a signal at the apparent fault location in the cable from outside. In combination with any PD measurement system, e.g., PHG TD/PD, the induced signal can be located and compared with the result of the partial discharge pre-location. The partial discharge location can thus be determined precisely.* Portable, battery-operated signal coupling device* Suitable for cables and cable accessories* Inductive signal coupling* Aviods costly, unnecessary replacements of PD-free cable accessories
-
Product
48V / 250 Amp Load
BD15-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Battery Charger/Discharger
BCD-3933T
-
Kongter Test & Measurement Co., Limited
Specially designed for single cell of 6V and 12V ONLY with max current of 50A. Three functions in one: charger, discharger and activator, which will facilitate your maintenance for batteries.
-
Product
Charge-Discharge Chassis For 208 VAC 3-phase
BT2203B
Chassis
The BT2203B is part of the BT2200 Series cell formation and lifetime cycler solution. It is an 8-slot mainframe for 208 VAC 3-phase power.
-
Product
Pressure Relief Valves
-
WITT is a manufacturer of safety relief valves or pressure relief valves. Safety relief valves respectively pressure relief valves or pressure safety valves are designed to protect against overpressure by discharging pressurised gases and vapours from pipelines, pressure vessels and plant components. Safety relief valves are often the last line of defence against explosion – and such an explosion could be fatal.
-
Product
Analog Insulation Resistance Tester (CE)
MIS-A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The single and fluorescent scale indicator for 3 ranges insulation measurements enabled easy observation. Especially, useful when working in dark place. Hand free and continuous measurements with custom made switch. Safe design with built in automatic discharging function for any capacitors present in the circuit. The voltage in the circuit can be pre-checked without any switch operation for safe insulation measurements. Compact, light weight and heavy duty rugged case.
-
Product
Lightning Surge Generator
CDN-5809
-
Shanghai Sanki Electronic Industries Co., Ltd.
CDN-5809 signal line/data line coupling decoupling network, unshielded asymmetric communication line suitable for surge pulses and ringing wave pulses, designed according to Figure 9 of the new standard IEC61000-4-5.Ed3. It also satisfies vibration Figure 9 of the ring wave standard IEC61000-4-12Ed2 requires unshielded asymmetry. According to the characteristics of the line, the pulse coupling can be realized by gas discharge tube, capacitor, diode and other different methods.
-
Product
±6 kV ANSI/ESDA/JEDEC HBM Test System
HBM-TS10-A
-
High Power Pulse Instruments GmbH
*±6 kV Human-Body-Model (HBM) tester according ANSI/ESDA/JEDEC JS-001 standard with C = 100 pF, R = 1.5 kΩ discharge network*Wafer, package and system level HBM testing*True HBM: the classical discharge network of the HBM-S1-A according the standard ensures compliant waveforms for all load conditions*No trailing pulses*Integrated 10 kΩ charge removal resistor*Integrated DUT HBM current sensor for real time transient current monitoring with 1V/A output sensitivity into 50 Ω digital oscilloscope input*Integrated DUT HBM voltage sensor for real time transient voltage monitoring with 1/200V/V output sensitivity into 50 Ω digital oscilloscope input*Integrated overvoltage protection of the DUT voltage sensor, DUTcurrentsensor and DC test interface for efficient overload protection of the digital oscilloscope and SMU during high voltage HBM testing*Integrated DC test DUT switch with automatic switch control*Integrated 50 Ω precision hardware trigger output for high speed digital oscilloscopes*Fast HBM measurements, typically 0.5s per pulse including one-point DC measurement between pulses*Eficient sofware for system control and waveform data management (fully compatible with TLP measurement data)*The sofware can control automatic probers for fast measurements of complete wafers*Compact size 145 mm x 82.5 mm x 44 mm of the integrated HBM pulse generator probehead*System controller size 483 mm x 487 mm x 133 mm*High performance and high quality components*Optionally available hardware upgrades to all HPPI fully integrated HBM/HMM/TLP/VF-TLP test systems TLP-3010C, 4010C, 8010A, and 8010C
-
Product
Lightning Warning Sensors
-
Lightning warning sensors measure the local, atmospheric electric field at the earths’ surface and the fluctuations in field strength. By monitoring the field strength, the potential for cloud-to-ground (CG) lightning discharges can be detected, and advance warning can be made when conditions are becoming favorable for lightning.
-
Product
Programmable DC Electronic Load - (Economical)
63200E Series
-
The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.
-
Product
Condenser for General Applications
PECA1
-
Lifasa - International Capacitors, SA
These capacitors are designed for application in circuits in which they are subjected to non-sinusoidal voltages and pulsed currents, such as, for example, switching and damping circuits. They can also be used as discharge and filtering capacitors, as well as for any DC application. This capacitor is especially suitable for applications in which a high life expectancy is required.
-
Product
Battery Loading Unit
BLUe
-
BLUe series Battery Loading Units; portable instruments for controlled & monitored discharge of batteries. It is designed for integrated site discharge test, design & QC test and also for monitoring discharge process of battery bank with connected load. Single autonomous unit having inbuilt display, keypad and wireless communication with PC makes it very easy to use. It comes in different configurations ranging from 12V to 380V discharge voltages and 50A to 300A discharge currents. Various options are available to control & monitor the discharge process. With the help of optional Cell Monitoring Unit - CELLMon, voltage of each individual cell can be monitored & data sent to main BLUe unit and then from main unit to PC via wireless communication. Each BLUe unit is supplied with PC downloading & analysis software for real time monitoring of discharge process.
-
Product
Battery Charge And Discharge Test System
9841
-
*Easy user interface*Measure Voltage, Current, Power, KWH, AH, Temperature, Reference Voltage*Accuracy Measure Time*Easy to see now test progress*Can cycle test*Provide Charge, Discharge, Suspend, FOR, LOOP Mode Select*When Charging, set the stop current to stop charging when fully charged so as to avoid overcharging that will damage the battery. When Discharge, set the stop voltage to stop discharge when discharging to lowest so as to avoid over-discharging that will damage the battery. *The test result will be stored to ACCESS data
-
Product
Battery Analyzers
CA 1550 – Commercial Version
-
*Portable Battery Charger / Analyzer.*0-25 Amp Charge.*0-50 Amp Discharge.*Fully adjustable.*115/230 Volt AC Input.
-
Product
TEV Antenna
-
TEV sensor is a partial discharge sensor whose working principle is based on a direct Capacitive coupling with a Switchgears earthed metal case. The two ends of TEV sensor can be coupled magnetically to virtually any opening on a metal Surface. It picks up the electric signal given by PD activity onto the two metallic surfaces. Thanks to its special design has high sensitivity, larger than other single ended TEV sensors. His compact and robust design (passive sensor) makes the TEV the optimal sensor for direct installation on medium voltage Switchgears.
-
Product
Battery Cell Formation System
17000 series
System
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
Product
Conventional Power Supply Design with Simple Analog Controls
VLF Series
-
VLF hipots perform voltage withstand tests and provide the voltage source for diagnostic cable testing. There is no better method for verifying the AC integrity of a cable than applying VLF AC voltage. Tan delta and partial discharge measurement accessories are frequently purchased along with VLF equipment to extend their capabilities.
-
Product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
-
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
Product
Automotive Battery Testers
-
ELAK Battery Testers are high-rate discharge testers. These testers impose a load on the battery, which is equivalent to that drawn by the starter motor from the battery, while cranking the engine. The tester studies the drop in battery voltage & indicates the condition of the battery if it is capable of starting the engine or not.
-
Product
Vacuum Discharge Test Equipment
DAC-VD-1
-
DAC-VD-1 can locate defective points such as scars or pinholes on stator coils and wires easily.By applying voltage in a vacuum chamber, the electric arcing from a defective part can be discoveredvisually in a short time. DAC-VD-1 can be used widely in variety of applications from product developments to outgoing inspections.
-
Product
Advanced Handheld Partial Discharge Detector
PDetector
-
Power Monitoring and Diagnostic Technology Ltd.
The PDetector is an ideal device for On-Line Partial Discharge (OLPD) testing of MV and HV equipment which employs all 5 types of OLPD sensor technology: Ultra-High Frequency (UHF), Acoustic Emissions (AE), Ultrasonic, High Frequency Current Transformer (HFCT), and Transient Earth Voltage (TEV). The information from multiple sensors gives the PDetector the versatility to detect all types of PD in all types of substation apparatus. The exact type of PD activity can be determined effectively using multiple on-screen data spectrum analysis.
-
Product
UNIVERSAL SYNCHRONOUS BALANCE CHARGER/DISCHARGER
U113AD
-
The U113AD charger is a fully integrated AC or DC powered charger capable of charging up to 150W. The built-in AC power supply allows the charger to be powered from a 110V wall socket at home or in the shop. The included DC input power plugs can be connected to a 12V lead-acid/gel cell batteries for charging at the field or track. The U113AD has the ability to charge, discharge and cycle Lithium (LiPo, LiIo, LiFe) packs up to 8 cells, NiCad and NiMH packs up to 26 cells, and Lead Acid batteries up to 36V. This is 12V higher than most battery chargers at this price point and is extremely useful for 36V applications such as E-bikes and scooters!
