Development Boards
See Also: Development, Software Development, Developers, Test Development
-
Product
PCI Digital I/O Boards
PISO-C64
-
The PISO-C64 has 64-channels of optically isolated digital outputs, arranged into two isolated banks. Each digital output offers a darlington transistor and integral suppression diode for inductive load. Isolated output channels are designed into group C and Group D. The power supply of the input port may use external power or the power from the PC side using DC/DC converter. The power supply of the output port should use external power. This interface board is easily installed in any PC/AT/XT compatible computer. The board interfaces to field logic signals, which eliminates ground-loop problems and isolates the host computer from damaging voltages. The ISO-C64 has one 37-pin D-Sub Connector and one 40-pin male header. Users can connect the digital signal through the second D-Sub connector. Each D-Sub connector contains 32 output channels.
-
Product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
-
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
Product
6U VPX Board
VP62009
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP62009 is a 6U VPX board based on Intel® Xeon® D-15xx processors, with more than 7-year life cycle. Supporting up to Intel® Xeon® D-1577 (16x 1.3GHz) processor, VP62009 is able to perform vector operation and floating point arithmetic that require high throughput. Besides, VP62009 supports Intel® Turbo Boost, with the processing speed of CPU up to 2.7GHz. The high-performance CPU and the Turbo Boost technology leave no worries for extra cost and complexity of system settings.VP62009 provides 2x 10 Gigabit Ethernet for VPX Data Plane communication, 2 x8 PCIe for VPX Expansion Plane communication, 4 GbE for VPX Control Plane communication. Rich data exchange interfaces on VP62009 make it easy to build box-level or system-level solutions.
-
Product
PCI Express Digital I/O Boards
PEX-D24
-
PCI Express Board with 24 DIO channels. Supports Linux, DOS, Windows 98/NT/2000 and 32/64-bit Windows 7/Vista/XP. Demo programs are provided for Turbo C++, Borland c++, Microsoft C++, Visual C++, Borland Delphi, Borland C++ Builder, Visual Basic, C#.NET, Visual Basic.NET and LabVIEW. Replacement product for DIO-24.
-
-
Product
Single Processor COMe Carrier Board
NS11001
-
LinkedHope Intelligent Technologies Co.,Ltd.
NS11001 is a single processor COMe carrier board based on the Intel® AtomTM N270 platform.The board size is: 200mm x 184mm.NS11001 supports both PCI bus and ISA bus in order to be compatible with customers’ legacy peripheral interface cards like MVB. In addition, it consists of a 10.4-inch external TTL LCD panel and a matrix keyboard interface.Bined with COMe module, NS11001 embedded platform using Intel mobile processor N270, 945GSE + ICH7M chipset, and the maximum power consumption at full load is 10W.The system displays interface provides up to 1600 * 1200 resolution display output, and has a variety of interfaces such as Gigabit Ethernet, UART, USB, PATA, etc.NS11001 supports extended working temperature and can be used in harsh environment.
-
Product
PC Board Accessories
-
ICP DAS USA offers Screw Terminal Boards for PC Based I/O Boards with or without din rail mounts.
-
Product
RELIABILITY BOARD (Reliability Test Board)
-
The reliability test board is used for testing of HAST, THB, HTOL, BURN-IN, etc. It is a product that evaluates the environmental test and durability when applied to actual products such as lifetime test, high temperature, low temperature, high humidity and thermal shock
-
Product
PCI Digital I/O Boards
PISO-813U/S
-
The PISO-813U/S card is the new generation product that ICP DAS provides to meet RoHS compliance requirement. The new The PISO-813U/S card is designed as a drop-in replacement for the PISO-813, and users can replace the PISO-813 by the The PISO-813U/S directly without software/driver modification.
-
Product
BARE BOARD TEST PROBES
-
Probe Technical DataMechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current60 18 mOHMS mean63 60 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper60 24 Kt gold plated over nickel63 24 Kt gold plated over nickelBARREL: Nickel silver60 24 Kt gold plated ID and OD over nickel63 No FinishSPRING: Music Wire, 24 Kt gold platedover nickel
-
Product
The Cyberbit Skill Development Platform
-
Cyberbit is the only platform that delivers the entire cyber skilling spectrum, on-demand, in coherent learning paths, validating your team’s performance and progress along the way.
-
Product
6U VPX PCIe to XMC Expansion Board
VP69601
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP69601 is a 6U VPX PCIe to XMC expansion board. Onboard there is a x8 PCIe 3.0 interface, and through a PCIe connector the x8 PCIe 3.0 turns into 2 x8 PCIe 3.0 linking to 2 XMC cards. The PCIe Switch IC on VP69601 supports DMA, so direct data transmission between peripheral cards can be realized.VP69601 can be installed in a standard VPX chassis and work as a peripheral board. VP69601 carries two XMC ports, through which users can expand various functional XMC cards needed.Apart from the traditional Air Cooling design, Linkedhope○R provides a Conduction Cooling version to guarantee working stability of VP69601 in extreme and vibration environment and in an extended working temperature from -40℃ to +70℃.
-
Product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
-
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
Product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
-
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
Product
Digital Expansion Board
MSXB 013
-
Digital Expansion Boards. The MSXB 013 Digital Input/Output Expansion Board expands 16 digital input lines and 16 digital output lines to 64 digital input lines and 64 digital output lines.
-
Product
6U Processor Board
CP62102
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62102, a product designed by LinkedHopeTM, is a 6U CPCI processor board based on Intel QM77/HM76 platforms supporting 3rd generation Intel i series CPU, up to 2.7GHz frequency, HD4000 integrated core graphics and dual-channel SO-DIMM memory (1333/1600) with up to 16GB DDR3 ECC (optional) and up to 64GB on-board SSD storage.CP62102 provides VGA and HDMI display and supports different display terminal output. CRT displays up to 2048x 1536. Besides CP62102 provides a wealth of software drivers (BSP) support, including Windows7, Windows Vista, Windows XP, WES 7, VxWorks, Linux, etc., as can reduce system integration workloads and end application development efforts, so to shorten time to market.
-
Product
PCI Daughter Boards
DB-24C
-
The DB-24C has 24 channels of optically isolated digital outputs, arranged into four isolated banks.
-
Product
6U Switch Board
VP68801
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP68801 is a China local design VPX Switch, compliant with VITA46.0, VITA48, and VITA65 specifications. The Profile of VP68801 is SLT6-SWH-16U20F-10.4.2, which uses Gb Ethernet as control plane and SRIO as data plane. It is mainly applicable to high-speed data exchange and routing among different types of payload boards in a VPX chassis. The switching board is designed as 6U VPX form factor, supporting both traditional air-cooled version and conduction-cooled version. With reliable anti-shock and vibration capability, excellent heat dissipation performance and unique environment protection design, the whole board can be stably operated in the wide temperature environment of -40°C to +85°C.
-
Product
Board Test
-
The Horizontal/Vertical Signal Integrity Manual Work Station allows for multiple size circuit board configurations.
-
Product
PCI Digital I/O Boards
PIO-D144U
-
Universal PCI, 144-channel OPTO-22 DIO board. Replacement unit for DIO-144.
-
Product
Flex, Rigid-Flex, Rigid Printed Circuit Boards
-
PCB boards are a common component of any electronic device. They work as a base for the other components and allow them to interface with one another. A PCB board can be made from several different materials, depending on what you need it for.
-
Product
Clock And Trigger Synchronization Board With Atomic Clock
CLKSYNC-PCI-AC
-
CLKSYNC-PCI-AC is a clock and trigger distribution board designed to provide up to eight synchronous clock and trigger outputs. The CLKSYNC-PCI-AC is designed for use with multi-channel, ADC and DAC systems where precise clock and trigger synchronization are required.
-
Product
DSP Based Serial Communication Board
CPCI-ISC8
-
The CPCI-ISC8 is an intelligent DSP based serial communication board. This 3U board is based on the CPCIIPC product and has been modified to remove the IPinterface and to support additional I/O features. The CPCIISC8 provides mechanical support and the electrical interfaces for an I/O mezzanine board. Multiple CPCI-ISC8 boards may be installed in a single system.
-
Product
PCI Daughter Boards
DB-8425
-
Connector interface for PISO-DA2Screw terminals for easy field wiring9-pin D-sub connector pin to pin screw terminal for PISO-DA2
-
Product
HIL Breakout Board
-
Onboard 192 pin snap-in terminal dramatically simplifies the wiring between your control hardware and your HIL system. As soon as the system is up and running there are 192 test terminals for easy access to all the interface signals: firing pulses, control feedback signals and other analog/digital I/O signals.
-
Product
Test & Development
-
Taking a new board level product or system from concept to deliverable requires feature-rich development and testing tools. Elma's wide range of Type 15 (desktop), Type 32 & D-Frame (portable/desktop) and Type 39E (development frame) chassis for VITA and PICMG bus architectures provide the platforms necessary to meet your needs.
-
Product
PC/104 OneBank Board
EMC²-7K325
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-7K325 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-Kintex7T also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options
-
Product
Backplanes And Connector Boards
-
Backplane and Connector Boards offer a cost-effective, flexible way to interface Advantech products' I/O features and enable board-to-board expansion.
-
Product
Express Multi Protocol Board
EXC-8000PCI
-
The EXC-8000PCIe is a PCI Express card supporting up to eight independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The EXC-8000PCIe supports extensive error injection and detection capabilities, IRIG B Time Code input, and can be ordered with an extended operating temperature range of -40ºC to +85ºC and conformal coating. The EXC-8000PCIe is supplied with C drivers, including source code.
-
Product
Carrier Boards
ROM-DB7500
-
ROM-DB7500 is an Evaluation Carrier Board designed for Advantech's RISC Qseven module. It is compatible with the ROM-7420 Qseven module and provides a thorough environmentfor RISC module board evaluation. It supports wide range temperatures and 12V power input through AC/DC power adapter.
