Programmable Logic Controller
Programmable Logic Controller
-
Product
PXI Resistor Module 2-Channel 1.5R to 8.19k with SPDT
40-293-124
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Logic Analyzer
Ant8
-
The Ant8 logic analyzer is compact, easy to use, powerful, and inexpensive. Ultra-portable - fits in a pocket. Powered from USB port - no additional power supply required. Applications run on any recent version of Windows
-
Product
PXI Remote Control Interface Modules and Kits
-
Take advantage of the latest high-performance, low-cost desktop PCs for control of your PXI system.
-
Product
Controllers & Software
-
Weiss Technik Controllers and Software offer advanced technology for Programming, Control and Monitoring for your testing.
-
Product
Programmable Relays
-
Omega offers a wide selection of programmable relays. From universal remote I/O modules to pressure switch accessories, you'll find everything you need to complete your application here.
-
Product
PXI Potentiometer Module 1x24 Bit, 0 Ohm to 16M Ohm
40-296-021-1/24
-
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
Precision Programmable Attenuator
RCDAT-30G-30
-
Mini-Circuits’ RCDAT-30G-30 is a precision programmable attenuator covering an extremely wide bandwidth, from 0.1 to 30 GHz. Its unique design allows attenuation settings to be programmed from 0 to 30 dB, in 0.5 dB steps with monotonic attenuation change per dB, even at the highest frequencies and attenuation settings. The attenuator can be controlled via USB or Ethernet, allowing control directly from a PC, or remotely over a network. VHF / UHF / L / S / C / X / Ku / K band testing.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm - SPST
40-294-133
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Precision Resistor Card 18-Channel, 1Ω To 239Ω
50-297-013
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Programmable Resistor Instrumentation
-
Power Interface, Prototype Cards and Programmable Resistor Cards for the PXI and GTXI platforms.
-
Product
DSP-Based 4/8-Axis Advanced Pulse-Train Motion Controllers
AMP-204C/AMP-208C
-
ADLINK"s new AMP-204C/AMP-208C DSP-based 4/8-axis advanced pulse-train motion controllers incorporate up-to-date floating-point DSP and FPGA technology, enabling high pulse output and encoder input frequency up to 6.5 MHz and 20 MHz respectively. Leveraging ADLINK" s Softmotion technology, the AMP-204C/AMP-208C offer impressive comprehensive and application-oriented motion functionality to reduce development time while maintaining superior throughput and accuracy. Superior synchronous motion control performance combines with point-table function integrating multi-dimensional interpolation, such as 3D linear/circular/spiral interpolation with enhanced trajectory and velocity planning, for contouring applications in semiconductor, display and conventional manufacturing industries. The AMP-204C/AMP-208C also support PWM control with three different control modes for frequency or duty cycle, benefiting laser engraving/marking/cutting applications. Moreover, hardware-based position comparison and trigger output are applicable in AOI applications.
-
Product
PXI Precision Resistor Module 3-Channel, 2.5 to 1.51M
40-297-144
-
This 3-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXIe8862 , 2.6 GHz 8-Core PXI Controller
787987-0118
-
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
Pressure Controllers
-
We offer pressure controllers as portable and as workshop models. We have automatic pressure controllers that can be used as stand-alone controllers or that can be combined with our calibrators to enable automatic paperless calibrations. We also offer manual pressure generators; hand pumps and manual pressure controlling modules.
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 2.5Ω to 472Ω
40-298-020
-
The 40-298-020 is a high density programmable resistor module with 9 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-116
-
The 40-297A-116 (PXI) and the 42-297A-116 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 1.8 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
CNC Controls
-
HEIDENHAIN offers a full range of CNC controls for all common types of milling and turning machines. From simple three-axis CNC machines to highly complex machining centers with up to 23 axes, HEIDENHAIN controls are always the right choice. They are practical, versatile, and high-performing, delivering convenient initial setup and productivity. Controls from HEIDENHAIN stand for exceptional performance and ease of use.
-
Product
Advanced Programmable IO Board
MS 1508
-
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
Product
PXI Precision Resistor Module 3-Channel, 3 to 1.51M
40-297-150
-
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Programmable DC Electronic Load
DL3000 Series
-
The DL3000 series is a cost-effective, economical programmable DC electronic load with a friendly human-machine interface and excellent performance specifications. It provides a variety of remote communication interfaces to meet diverse testing needs for design and testing. A wide range of solutions are available for a wide range of industries including automotive electronics, aerospace and fuel cells.
-
Product
Programmable Limit Switch
PLS1000
-
Computer Conversions Corporation
The PLS1000 is a programmable limit switch designed to allow convenient programming of 16 circuits.The PLS1000 is designed to be panel mounted.
-
Product
Drives & Controllers
-
Most popular, Works with all McPherson SpectrometersDrive of Choice for high precision wavelength control settingUp to 50,000 steps per revolutionComputer control, RS232 (provided with USB adapter)Maintains all manual monochromator controlAvailable with fit kits to upgrade older instruments
-
Product
Controllers
BKM91D
-
BK MIKRO BKM91, BKM91D, BKM91PN and BKM92KIO controllers utilize the premium version of firmware which allows for multiple tools or functions to be programmed. These controllers are typically used when advanced features are required such as checking for broken tool inside of a CNC tool changer or checking multiple object or free space positions.
-
Product
Lighting Control
-
ICP DAS USA’s LC Lighting Control Series simplifies the way you manage your lighting systems. The LC series allows the user to control multiple devices on a single user interface device. Unlike the traditional twisted-pair lighting control system, the LC series eliminates the use of wires, reducing installation and energy consumption costs and increases flexibility over where switches and sensors may be placed.
-
Product
Voltage Control Attenuator
-
Voltage variable attenuator offering infinite attenuation precision and broadband performance
-
-
Product
Automated Programmer Superpro Sb05
-
※ Four Pick & Place nozzles, Eight socket pressing actuators and 2 tape feeders※ High throughput up to 2400UPH※ Embeded with eight ultra-high speed programmers SuperPro / 7500, each with up to 4 sockets, totally 32 sockets. Throughput 60 times higher than SuperPro / SB01 for eMMC devices※ Supports over 80,000 devices from over 300 IC manufacturers※ Supports tray, tape and tube input and output. Supports laser and ink marking※ Short change-over time※ Intelligent s/w cuts learning curve and setup time, makes task management an easy job※ Compact sizeHigh throughput：4 nozzles, 8 independent socket pressing actuators and 2 tape feeders. Up to 2400 UPH for devices with programming time less than 50 sec. Throughput 0.6 to 60 times higher than SuperPro/SB01, especially higher for large capacity devices like eMMC, NAND /NOR FLASH,SPI FLASH. Suitable for both small and large capacity devices. Prog. Time (S) 50 60 120 180 240 300 UPH (unit per hours) 1600 1600 840 560 420 336 Accurate positioning：Equipped with high performance servo system, precise CCD cameras and vision algorithm for device alignment and sockets / pick & place spots positioning.High performance programmers： 8 ultra-high speed universal gang programmers SuperPro/7500 resident. Each with up to 4 sockets, totally up to 32 sockets in the system. Supports up to 100,000 devices from over 300 IC manufacturers and growing.Varied I/O devices：Supports tray, tape and tube input and output. Supports laser and ink marking. Supports packing conversion and can work as a packing conversion machine alone.Short change-over time：I/O devices and socket adaptor are easy to be changed when programming task need to be changed. Socket positioning can be performed automatically. Projects can be loaded automatically with barcode scanning.Powerful and intelligent software：Setup data saved for next operation, log file and statistic reports for quality and yield traceability, flexible sockets prohibition strategy promises high yield rate for unattended operation, graphical user interface cuts learning curve, prevents chip over-lapping by socket checking before chip placing.Remote Control：Remote project loading, quality monitoring, volume control, file security.
-
Product
Control Center
COSYMA
-
COSYMA is the control centre for APCOS®4000, consisting of a comprehensive and versatile application software that includes the following components:*Communications Network Control (CNC)*Radio & Device Control (RDC)*Secure Automatic Military Message Handling System (SAMMS)
-
Product
Recloser Control Analyzer
GEN-I3V
-
The GEN-I3V is a universal analyzer for Recloser Controls and a Recloser Simulator of up to 15 Amps. In addition to current injection up to 15A, it also supplies 3 voltage sources to perform a complete range of testing and provides high precision curves in no more than 10 minutes.
-
Product
System Controllers
-
Kratos Defense & Security Solutions, Inc.
- Precise and accurate six-axis tracking control- An easy-to-use graphical user interface accessible from anywhere on the network- Optional integrated control capabilities and hardware, such as an integrated spectrum analyzer, beacon receiver, uplink power control, auto acquisition, carrier monitoring & logging, and much more
