Circuit
-
Product
Air Core Test Lab Reactors
-
Test Laboratory Reactors are designed for high voltage and high power test laboratories. They are designed to withstand the most extreme electrical service conditions during test periods. Design techniques are implemented in accordance with the most demanding service conditions. These reactors are used for various purposes in test laboratories such as current limiting and synthetic testing of circuit breakers, capacitor testing, artificial line simulation etc.
-
Product
Emergency/Panic Button
ENVIROMUX-EBS
-
Sends activation signal when button is pressed. For normally closed or normally open circuit connections. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft (305 m). Dimensions WxDxH: 1.7x2.9x4.6 in (43x74x117 mm). Regulatory approvals: RoHS.
-
Product
LED Test Programmable DC Electronic Load
IT8912E Series
-
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
Product
Shunt
-
Shunts are used with Moving Coil Ammeters for the measurement of current in DC Circuits.
-
Product
Topside Probing In-Circuit Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
Product
Primary Current Injection
PCI-600
-
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers.
-
Product
SPICE circuits & model Debugger / Analyzer
SpiceVision PRO
-
SpiceVision PRO takes the complex SPICE descriptions produced by many EDA tools and generates clean, easy-to-read transistorlevel schematics and circuit fragments, and design documentation to speed up debugging and project development.
-
Product
Interface Test System (ITS)
-
The SecuControl ITS is a modular test block designed to meet the stringent safety, reliability, and performance needs of IEC-based substations. With fully finger-safe construction, keyed STP test plugs, and built-in CT Shorting, the ITS enables safe, repeatable secondary injection testing, without the risk of open CT circuits or accidental trips. It is the ideal solution for structured, standardized testing across protection systems.
-
Product
Light / Lux Meter, Calibrated w/D & U, 50000 lx, 100 lx, 4 %, 185 mm, 78 mm, 38 mm
72-7250 CAL DU
-
The 72-7250 CAL DU from Tenma is a digital light meter with RS232 capability. It has custom one-chip microprocessor LSI circuit which ensures high accuracy. The meter features 13mm (0.5”) super large LCD display with contrast adjustment for best viewing angle, data hold and auto power off. It records maximum, minimum and average readings with RECALL facility. The 72-7250 has RS-232 PC serial interface, user selectable lighting type (tungsten, fluorescent, sodium or mercury, daylight) and zero adjustment by push button. The meter operates from 9V battery.
-
Product
PXI BRIC4 FIBO Matrix Dual 62x4 2pin brkout
40-592A-012
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Power Distribution Boards
-
Power distribution systems can be offered in addition to solutions for power supplies. This includes power distribution boards, which take over the power distribution in your system. When developing the system solution, in addition to the technical requirements such as high energy efficiency, simple further processing is decisive. The competence for high-performance circuit boards, enclosure constructions as well as assembly and system tests, which has been developed over the years, enables us to offer you the best possible power supply and distribution.
-
Product
4.5-Digit Handheld Multimeters
U1280 Series
-
The Keysight U1280 Series handheld digital multimeter (DMM) is a true RMS multimeter which provides an accurate and reliable measurement. You will enjoy 60,000-count display resolution and 0.025% basic DCV accuracy for troubleshooting electronic circuits.
-
Product
6-12V Heavy Duty Circuit Tester
1671
-
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems.1. Locate short, ground or open circuit.2. Make it easy to find out where current is present.3. The most essential for troubleshooting automotive electrical systems.4. Checks series-parallel switch and solenoid on tractor-trailer start system.
-
Product
Microcontrollers
-
A compact integrated circuit designed to govern a specific operation in an embedded system.
-
Product
AC Voltage Detector
VT-2
-
The Non-contact AC Voltage Testers are easy to use — just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there’s voltage present. Electricians, maintenance, service, safety, personnel, and homeowners can quickly test for energized circuits in the workplace or at home.
-
Product
High and Low Temperature Humidity Chamber
GDJS/GDJW
-
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
Product
Cable Continuity Detectors
-
Shenzhen Noyafa Electronic CO.,LTD
NOYAFA Cable Continuity Detector can test the open circuit, short circuit, crossover and continutiy for RJ11/RJ45/BNC/USB cable, and the test result is displayed by the visible LED light status.
-
Product
Test Fixture Kits
-
Our test fixture kits provide cost effective solutions to printed circuit board testing and other devices under test. Our modular kits are available in multiple sizes and configurations. They can easily be customized if our standard doesn’t meet your requirements. Removable side panels for ease of fabrication for I/O connections, switches or other hardware.
-
Product
Heavy Duty Circuit Tester with Retractable Wire & Long Probe
27250
-
Features an extra long wire that stretches up to 12 feet for use, then automatically retracts. Quickly and easily check electrical circuits and accessories on 6 and 12 volt systems. Great for use on cars, trucks, boats, trailers, motorcycles, airplanes and snowmobiles. Heavy duty ground clip with insulator. 6 1/2" long, insulated probe.
-
Product
Telecomunication & Electrical Insolation- Continuity-Voltage-MOV Tester(LCD Display)
1165IN
-
Standard Electric Works Co., Ltd
● Measures insulation (MΩ), Continuity (Ω) , AC and DC voltage● Six insulation test voltages (DCV): 50V, 100V, 125V, 250V, 500V, 1000V● 68x34 mm (2.677x1.338 inch) large LCD● Function rotary switch design for easier operation● Intuitive operation for users● User friendly interface● Auto ACV/DCV detection● Audible voltage warning● DAR/PI indication● Backlight function● Automatic circuit discharge● Test insulation at rated voltage into a 1mA load● Auto ranging● Fuse protection● EnerSave function● MOV test function
-
Product
Press Down Rods Bed of Nails Testers
Prober Press Rods Family
-
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
Product
Power Supply 302D
-
reliable and precise power of the output DC stabilization and digital LED displays. The output voltage is adjustable from 0 ~ 15V DC in smoothly with the knobs to control coarse and precise. Output current is regulated (limited) fluent in 0.6A ~ 2A. Securing the power supply protects it against accidental short circuits, and thus against overload and damage. In addition, the power supply has 5 fixed output voltages: 1.5 V, 3.6 V, 4.8 V, 6 V and 7.2 V, specially designed for mobile services, power systems and electronic components, etc. can be used in the design of electronic products, scientific work in laboratories, production lines and in teaching. Power can be used in the design of electronic products, scientific papers, laboratories, production lines and in teaching.
-
Product
2 phase 120/240VAC SDP-30KW split phase inverter
SDP-30KW
-
Zhejiang Sandi Electric Co., Ltd
SANDI SDP series Pure Sine Wave Inverter is the one of the most advanced technology DC to AC conversion products in the world, it’s suitable use for areas without electricity, providing a complete power solution for strict demand applications. With SVPWM technology it has high conversion efficiency, high instantaneous power and low losses power output pure sine wave, applying to capacitive, inductive and nonlinear mixed-load, with superior load capacity, perfect protection function: overload, short circuit, low/over battery voltage, improper operation etc, which won’t cause mechanical failures.
-
Product
Fuse Saver
7611
-
Peaceful Thriving Enterprise Co Ltd
The device use microelectronic technology to monitor the variation of current, which helps technician to protect the automobile circuit from current overloading during the maintenance.
-
Product
120 A High Voltage 50 Ω Pulse Generator
TLP-12010C
-
High Power Pulse Instruments GmbH
- High pulse output current up to 120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical rise time 100 ps (0 A to 40 A) and 300 ps in high-current mode (0 A to 120 A)- Wafer, package and system level TLP, VF-TLP and HMM testing- Up to 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 USB programmable pulse rise times: 100 ps to 50 ns (custom selectable)- 8 (optional 9) programmable pulse widths: 0.5 ns (optional), 1 ns to 100 ns (0 A to 40 A), 1 built-in pulse width: 100 ns (>40 A)- The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0 A to 40 A)- Optional external pulse width extensions from 5 ns to 500 ns (>40 A to 120 A)using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient sofware for system control and waveform data management- The sofware can control automatic probers for fast measurements of complete wafers- Combines TLP-12010A and TLP-4010C into one system- Can be operated together with TLP-12012A6 and TLP-3011C pulse width extenders- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface
-
Product
T3DSO Passive Probe, 350 MHz, 10X, 10 MOhm, 300V/600V
T3PP350A
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
Product
High Insulation Digital Clamp Tester
HCL-3000D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide AC current measurements for 0.001A～20A.*Easy operation, Push to Open and Pull to Disconnect Mechanism.*Safe AC current measurements for high voltage circuit (AC80 to 7000V).
-
Product
Single-Ended Amplifiers
Op-Amp
-
For designs requiring single-ended amplifiers (op amps), Analog Devices' portfolio of high speed op amps and precision op amps provides a broad choice of products that deliver unmatched performance. Explore op amps by parameters, and find expert system-level advice on design problems with our amplifier reference designs (Circuits from the Lab®), design tools, selection guides, calculators, and SPICE models.
-
Product
192 X 1 Or 96 X 2 cPCI Low Thermal Relay Scanner Module
DP-cPCI-4032
-
DP-cPCI-4032, is a hot swappable high density 192x1 or 96x2 relay scanner module. DP-cPCI-4032 is implemented as a 6U cPCI module.The 96 channel scanner is divided into six banks of 16x2 scanner. The banks are isolated from each other using tree switches. Six tree switches are used, one tree switch for each bank. A common tree switch is used to group all the six banks. Depending on the application requirement, it can be configured as 96 x 2 or 192 x 1 scanner. For short circuit protection, resistors are provided for all the common terminals.
-
Product
Wire Systems Analyzer
Console Test Systems (CTS)
-
Wire Systems Analyzer Commercial Roll around detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex. Used to verify the operation of relays, circuit breakers, indicators, switches, diodes, transformers, 1553 couplers, etc.
