Circuit
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 122Ω
40-251-012
Programmable Resistor Module
The 40-251-012 is a programmable resistor module with 8 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXI Breadboard Module, 1-Slot, 20-Pin GMCT
40-220A-801
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
Ohm-Stat Digital Display Megohmmeter
-
Measures resistivity RTT, RTV, and RTG 103-1012 ohms/sq., ohms, ohm-cmRelative humidity 10% 90% RHTemperature 32oF 100oFDigital display: easy to interpretNIST calibration includedIncludes chair probe to measure smocks, earth ground, chairs, and resistance probes: $400 value for freeResistivity probe built in the bottom of meterProduct conforms to the ESD S.20.20 spec standardsCE mark includedThe kit includes, two (5) lb probes, coil cords, hard carrying case, battery, 110v or 220v adaptor, garment clips, chair probe, and ground circuit tester
-
Product
Economy Mechanical Calibration Kit, DC To 6 GHz, 7 Mm
85031B
Mechanical Calibration Kit
The Keysight 85031B calibration kit contains a set of precision 7 mm fixed terminations and a one-piece open/short circuit used to calibrate Keysight network analyzers for measurement of devices with precision 7 mm connectors. This kit is specified from dc to 6 GHz.
-
Product
Rogowski AC Current Probe, 23 MHz, 3000 A
N7040A
High Current Probe
The Keysight N7040A Rogowski coil current probe is designed for measuring AC currents up to 3,000 A with the bandwidth ranging from 3 Hz to 23 MHz. The probe is easy to use because it has a thin, lightweight, flexible and simple-to-use clip-around Rogowski coil that enables current measurement in the most difficult to reach parts and confined spaces of a circuit under test. It can also measure large AC current without increase in transducer size.
-
Product
PXI BRIC4 FIBO Matrix Dual 31x4 2pin brkout
40-592A-011
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Current Logger Sensor
NUL-202
-
This sensor can be used to measure the current in parallel or series branches of low voltage AC and DC circuits and also to investigate the dependence of the current flow through components on the voltage across them.
-
Product
Aeroscope Wireless Oscilloscope Probe
-
A wireless, ultra-portable oscilloscope with impressive specs – debug circuits in their natural environment.
-
Product
ONU RFTV Optical Receive Module
M9130
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai M9130 optical receiving module is designed for ONU optical fiber network unit. This series of product with perfect detect and remote shutting off function adopts high sensitivity receiving tube and Huatai special low noise matching circuit. It is a kind of high index, low power consumption and high cost performance RFTV optical receiving unit.
-
Product
AC-DC Dual and Triple Output Power Supplies
-
These dual tracking output mini-modules are compact and convenient sources of the voltages required to power operational amplifiers and related circuits.
-
Product
Development Platform
LaunchPad™
-
Begin rapid prototyping applications in minutes with our microcontroller-based LaunchPad kits, Sitara™-processor-powered BeagleBoards and SimpleLink™ wireless connectivity SensorTags. The Sidekick line of kits from Seeedstudio offer customers a quick way to evaluate custom circuits with many of the popular microcontroller development kits available on the market.
-
Product
Split type AC Current Transformer
CTS-600
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*5A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy to install by metal fitting.
-
Product
Probes, Clamp-On
EM-6981 | 9 KHz – 110 MHz
-
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
Product
Hall Effect DC Current Sensor
CYHCT-WS3
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
Product
EOS Tester
KT-200SG
-
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
-
Product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
Monolithic Microwave Integrated Circuit (MMIC) Amplifiers & Switches
-
Microsemi's portfolio of MMIC products targets a broad range of applications including those in electronic warfare, radars, instrumentation (test and measurement) and microwave communications. The portfolio comprises broadband amplifiers (both power and low-noise), amplifier modules, prescalers, attenuators and switches spanning DC to 65GHz based on high-performance process technologies. Microsemi offers 18 distributed amplifier products including industry-leading DC-65GHz MMICs. Microsemi's prescalers combine higher frequency operation, the flexibility to divide by a large number of ratios and very good residual phase noise.
-
Product
SIMRC - 8 x 2 Matrix 2-Pole
1030-R-8-2-2-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Rogowski AC Current Probe,30 MHz, 600 A
N7041A
High Current Probe
The Keysight N7041A Rogowski coil current probe measures AC currents up to 600 A, with bandwidth ranging from 12 Hz to 30 MHz. The probe has a thin, lightweight, flexible, and simple-to-use clip-around Rogowski coil that enables current measurement in the most difficult-to-reach parts and confined spaces of a circuit under test. It can also measure large AC current without an increase in transducer size.
-
Product
Filters
-
In order to minimize filter roll-off, we start with a quality, highly polished substrate and apply layers of metallization within tight tolerances. Our highly anisotropic ion beam etching process enables us to produce features down to 10 microns. Furthermore, the milling process yields a high consistency from circuit to circuit meaning that whether we produce 1 or 100,000 filters, each one will have consistent filter roll-off characteristics.
-
Product
Switchgear Testing Solutions
-
IES Systems is a world leader in the design and manufacturing of power switchgear test systems.*GFCI/AFCI Circuit Breaker Test Solutions*Medium Voltage Breaker Test Solutions*Residential Circuit Breaker Test Solutions*Molded Case Circuit Breaker Test Solutions*AIR Circuit Breaker Test Solutions*Vacuum Bottle Test Solutions
-
Product
PXI BRIC8 FIBO Matrix Dual 100x4 3pin brkout
40-592A-105
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Plastic Fabrications Testing Equipment
-
PD and PHD Pinhole/Holiday Detectors have an alarm circuit to alert the operator when a fault has been located and the required test voltage can be set on the unit's meter. Spark Testers provide an inexpensive means of testing but have no output voltage meter or audible alarm. However, they can test joints even if the backing is not connected.
-
Product
Impedance Analyzer, 1MHz to 500 MHz/1 GHz/3 GHz
E4991B
Impedance Analyzer
The E4991B Impedance Analyzer has a frequency range of 1 MHz to 3 GHz. The E4991B provides 0.65% basic accuracy over a wide impedance range with a 40 V built-in DC bias source (Option 001). The equivalent circuit analysis function supports seven different multi-parameter models and helps you to simulate your own equivalent parameter values of components.
-
Product
PCIe Digital I/O Board, 16 Optically Isolated I/O Channels, 24V
APCIE-1516
-
8 digital inputs, 24 V, isolated15 interruptible inputs8 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
PXI BRIC8 FIBO Matrix Dual 93x4 2pin brkout
40-592A-113
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
(70×90×15mm) C-Band DWDM Full Function Pre EDFA Module
WPA4300-FM02
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Huatai WPA4300-FM02 series with 70 × 90 × 15mm MSA compact package, is a digital control circuit with DWDM full function preamplifier module. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Suitable for C-Band 44 or 88 waves DWDM system applications.
-
Product
Switches-SP6T
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer an extensive collection of switches covering multiple commercial and aerospace and defense markets. Our product portfolio has a broad frequency spectrum from DC to 70 GHz. Our silicon Heterolithic Microwave Integrated Circuit (HMIC) PIN diode process is ideal for high power and broadband switches operating from 50 MHz to 26 GHz. Our AlGaAs PIN diode process can extend the upper frequency range of our switch die beyond 70 GHz and is ideal for instrumentation and radar applications. Our GaAs pHEMT and MESFET technology is ideal for fast switching and low control voltage switches optimized for both narrow band and broadband applications. Our 75 Ohm absorptive switches are designed specifically for demanding CATV, FTTx and DBS Infrastructure and CPE applications.
-
Product
Electronic Components
-
We supply a wide range of components and materials to the electronics industry, such as: integrated circuits for personal computers, semiconductor materials for system LSI, optical communication materials for telecommunications, components for display devices seen in smartphones and projectors, and materials used in solar cells and lithium batteries.
-
Product
Multi-Channel Home Energy Monitor
ECM-1240
-
Cascade several ECM-1240s to monitor all of your panel circuits! * Locate the guzzlers. * Set consumption budgets/goals. * Find loads or appliances requiring maintenance or replacement. * Determine the optimum balance between comfort and energy cost. * Reduce peak demand and SAVE MONEY!
