Circuit
-
Product
Battery Internal Short Circuit Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Battery Internal Short Circuit Tester
-
Product
CT Ratio/Burden Tester
1047
-
TESCO’s new CT Ratio/Burden Tester (Catalog No. 1047) is a lightweight, portable and highly accurate in-service test set to assist in finding lost revenue by testing the accuracy of your meter circuits. The Tester can help determine if there are installations errors, loose connections, incorrect ratios, resistance buildup, open CT’s, or manufacturers defects. The CT Ratio/Burden Tester measures and displays the primary and secondary current of the CT under test, and the ratio of the currents. All test data is stored in the internal memory and easily uploaded to a PC.
-
Product
PXI 32 x SPDT Reed Relay
40-110-121
Relay
Our 40-110 and 40-115 range of reed relay switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120/125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
Product
Power Quality Meter
Nexus 1450
-
The Nexus 1450 is a powerful state-of-the-art power meter that provides high-precision electrical energy measurements and records waveforms. This equipment allows you to measure power quality and determine the reliability of electrical power. The Nexus 1450 meter allows you to see the reliability of the power circuit to determine the causes of failures, surges and voltage drops, and harmonics.
-
Product
Power Device Analyzer / Curve Tracer
-
The B1505A Power Device Analyzer / Curve Tracer is focused on the needs of power device manufacturers, while the B1506A Power Device Analyzer for Circuit Design is focused on the needs of power electronics circuit / product manufacturers. The B1507A Power Device Capacitance Analyzer helps both power device development engineers and power circuit designers maximize product value by revealing device capacitance characteristics.
-
Product
Balanced Measurements
-
The unbalanced interface of a VNA is not very well suited for measuring balanced circuits like antennas, transmission lines or chip impedances. In fact it is nearly impossible to get a decent calibration on a balanced 2-port measurement using coax cables.
-
Product
Circbord
8023
-
VECTOR Electronics and Technology, Inc.
3-hole solder pad for interconnecting multiple component leads. I/O area with square solder pads for connectors mounting. Circuit pattern etched onto both sides. Double sided with plated thru holes. Solder mount DIP sockets or IC devices with any lead spacing.
-
Product
PXI Breadboard Module, 1-Slot, 15-Pin D-Type
40-220A-601
Breadboard Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
Electronic System Design
ESD
-
Smart connected devices are everywhere, in homes, in transportation, and at work. This means electronic system design (ESD) is having a greater influence on almost every type of product requiring new simulation tools to help achieve electronic, electrical, mechanical, thermal, and connectivity goals. Altair’s simulation-driven design tools enable your team of specialized engineers to collaborate across all aspects of printed circuit board development from concept to manufacturing. Our products streamline your process, eliminate design iterations, and reduce time-to-market.
-
Product
Functional Testing of Printed Circuit Boards, Sub Assemblies and Finished Products
Testpoint
-
Yelo Testpoint is an extremely modular and flexible system, allowing you to scale to any size operation, and to add almost any new test requirements. Ideally suited to cellular manufacturing, the system can be used to complement an existing ATE, as a functional test add-on, or as a diagnostic work station. Its compact, space-saving construction has multiple interface positions to accommodate both horizontal and vertical connections.
-
Product
Weather Radar Receiver
-
This is an example of a custom four-channel C-Band Receiver uses a single conversion technique to translate incoming 5.56 GHz radar signals to a 60 MHz IF. The Receiver is divided into two polarization sections, each with a dedicated channel for the received signal and a second channel for a reference signal originatingfrom the transmitter. There are two identical circuits in the Receiver, one reserved for vertically polarized signals, and the second for horizontal signals.
-
Product
Primary Current Injection Test Sets
-
Our primary current injection test sets cover from 750A through to 6000A. Available in single phase, testing applications include testing and timing of under and over current relays, circuit breakers and CT ratio testing.
-
Product
SMD Test Probes
-
The Parrot Clip, model PCM W1 or PCS-MB W1 invention can be connected to resistance’s, diodes, integrated circuits (SOIC, SO) etcThe advantage of the Parrot Clip is given by the double metal connection made between the new metal tip and the steel hooked rod, spring loaded. This connection, being made by metal parts is electrical and mechanical reliable, even if the contact point are small. Connections are resistant even at high temperatures.
-
Product
Voltage & Continuity Tester
ET250
-
The ET250 voltage and continuity tester incorporates an LCD display, measures AC/DC voltage up to 600V and can test GFCI protected circuits. Both voltage testers have a tough meter design and are rated CAT IV 600V for safety.
-
Product
Handheld Digital Multimeter, 4.5-digit
U1252B
Digital Multimeter
The Keysight U1252B 4.5-digit handheld digital multimeter (DMM) is feature-packed to simplify the troubleshooting of electronics and electrical circuits on the bench or in the field. Key capabilities include manual and automated data logging to both DMM and PC. For those long, continuous measurements, the DMM equips you with the easy-to-use GUI data-logging software to automate virtually unlimited data recordings to PC. The U1252B comes with an integrated 20 MHz frequency counter for high frequency measurements, and a built-in programmable square-wave generator with selectable frequency and duty cycle. With the versatile U1252B, you are well equipped to perform thorough troubleshooting of any faulty circuit.
-
Product
CAT-5 Video Drivers
-
Analog Devices provides designers with a robust portfolio of high speed triple, differential, and single-ended input to differential output CAT-5 video drivers. We designed the technology for the highest resolution component video signals, but it can be used for any type of analog signals or high speed data transmission over either Category 5 UTP cable or differential printed circuit board (PCB) transmission lines. Manufactured with our second generation XFCB bipolar process, the drivers have large signal bandwidths of 700 MHz, fast slew rate, and output amplitude and phase matching balanced to –60 dB at 50 MHz.
-
Product
High Power Switch and Bias Module
-
Macom Technology Solutions Holdings Inc.
MACOM’s High-Power Switch and Bias modules are extensively used in 4G and 5G TDD base stations as well as aerospace and defense applications. The PIN Diode Switch features high power handling, low insertion loss, and super board band performance. The integrated bias controller utilizes a boost circuit and provide the driver circuitry to the switch. The modules require only a single 5 V supply, and a single TX / RX control signal which greatly reduced the customer design complexity.
-
Product
Selenium Rectifiers
-
Selenium rectifier stacks are made up of selenium cells, which are mounted together and circuited as required for each application. They are available in configurations to suit all of the rectifier circuits.CEHCO is a leader in supplying selenium rectifier stacks. We are selenium rectifier replacement specialist. In fact, the company can assemble and deliver any selenium rectifier in 48 hours or less. And the stacks contain extremely high-quality, high-density, vacuum-processed cells to ensure uniformity, stability, and long life.
-
Product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
-
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
Product
PWM Type AC Power Supply
LSP-5KVA
-
• Circuit Type: (IGBT) MPWM Pulse Duration Modulation • Input: 1 Phase 220V±10%, 50Hz/60Hz±5% • Output Voltage: HIGH/LOW Adjustable 1)1 Phase Voltage Range: (HIGH)0～300V, (LOW)0～150V 2) Nominal Voltage: +10%～+25%, -10%～-30% • Output Frequency: 50Hz, 60Hz, adjustable between 45 and 70 Hz, 400Hz • Load Voltage Stabilization Rate: ≦0.5% • Frequency Stabilization Rate: 0. 1% (Fix Point 50Hz, 60Hz and 400Hz) • Wave Distortion Rate: ≦2% (Resistor Load); Efficiency: ≧85% • Output Instruments: Frequency Indicator, 4-digits RMS digital frequency indicator, resolution is 0.1Hz Voltage Meter, 4-digits RMS digital voltage meter, resolution 0.1V Ampere Meter, 4-digist RMS digital ampere meter, resolution 1Ma Power Indicator, 4-digits RMS digital power indicator, resolution 1W Power Factor Meter Resolution 0.001 • Protective Devices: Over load, short circuit, over voltage, over current, over temperature protective and alarm devices • Operating Environment: Temperature 0～40℃ Relative Humidity 0～90%
-
-
Product
PXI Breadboard Module, 2-Slot, 96-Pin Micro-D
40-220A-002
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PMC
-
A PCI Mezzanine Card or PMC is a printed circuit board assembly manufactured to the IEEE P1386.1 standard. This standard combines the electrical characteristics of the PCI bus with the mechanical dimensions of the Common Mezzanine Card or CMC format (IEEE 1386 standard).
-
Product
0.5-2.4GHz Instantaneous Frequency Measurement Unit
DR063-M2
-
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
-
Product
Tone & Probe Kits
-
Triplett Test Equipment & Tools
ProTone Wire Locator Kit features a powerful tone generator and a filtered, ultra-bright lighted probe. The CTX590 functions as a high quality wire locating tool that uses an inductive probe to sense a tone placed on the wires by its associated tone generator. The tone generator provides RJ11, RJ45 and insulated alligator clip connections. The Red/Green LED on the probe indicates continuity, voltage, and polarity. The probe also includes an ultra bright LED tip, fluorescent light noise filter and sensitivity control. The CTX590 can be used for tracking down short circuits, telephone central office connections, and other wire locating applications. Includes (2) 9V batteries and case.
-
Product
CPCI Test Extender 6Ux400mm
117EXT6116-0XXX
-
The cPCI extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged on each 2mm HM connector in P1-P5. Each line in rows A-E can be isolated with the DIP switches.
-
Product
AC/ DC mA Current Clamp-on Transducer
CA-60
-
This miniature clamp meter features two Hall effect sensors. For use with any multimeter with 200mV or/and 2V ranges for direct readout input impedance of least 1M ohm. High conversion factor for low DC and AC mA measurement. With the small jaw size it can fit into tight space in circuit panel or wire bundle to take the reading.
-
Product
Phase Failure Detectors
DSP
-
Your product The DSP-1L or DSP-1LM is used to protect your three-phase motors against phase loss, imbalance, or reversal. It continuously monitors each phase of your power supply. In case of a problem, it cuts the power to the control circuit to protect the affected motor.
-
Product
EMI Filters And Application-Specific Integrated Products (ASIP)
-
An electromagnetic interference (EMI) filter is used in electronic circuits to improve system immunity against unwanted external electromagnetic signals from neighboring circuits and to avoid emitting radiation (“noise”) that may disturb the same nearby circuits by canceling unwanted frequencies.
-
Product
Electricity Meters Tester
Caltest 10
-
Calmet Smart Calibration Devices
Single phase portable electricity meters tester class 0.5% powered from tested circuit with load force possibility apart from tested object. There is no need to disconnect the users during measurement
