Electro-Metrics Corp.
Electro-Metrics Corporation is a leading designer, producer, and integrator of antennas, sensors, and systems for broadband RF technologies.
- (518) 762-2600
- (518) 762-2812
- info@emihq.com
- 231 Enterprise Road
Johnstown, NY 12095
United States of America
-
Product
Probes, Clamp-On
EM-6987 | 1 KHz – 110 MHz
-
The EM-6987 is capable of measuring signals and noise superimposed on power currents up to 300 A from DC to 400 Hz. Intermodulation effects on current probe output are also negligible.
-
Product
Antenna, Log Periodic
EM-6951 | 300 MHz – 1 GHz
-
The Electro-Metrics EM-6951 Log Periodic Antenna was designed to operate over the 300 MHz to 1 GHz frequency range.
-
Product
Antenna, Active Loop
EM-6869 | 9 KHz – 50 MHz
-
The Electro-Metrics EM-6869 Active Loop Antenna is used with any receiver or spectrum analyzer with 50 ohm input and covers the frequency range of 9 kHz to 50 MHz.
-
Product
Antenna, Octave Band Horn
EM-7021 | 2 GHz – 5 GHz
-
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
Product
Antenna, Pyramidal Horn
EM-6119 | 1.7 GHz – 1.9 GHz
-
The EM-6119 Pyramidal Horn Antenna is specifically designed for operation in the PCS and DCS bands (1700 MHz to 1900 MHz). Over this frequency range this antenna exhibits a typical gain of 10 dBi, and provides an excellent match with typical VSWR of <1.2:1. This antenna is useful in transmitting as well as receiving signals in this band.
-
Product
Shielding Effectiveness/ Conductivity Test
EM-2107A | 30 MHz – 1.5 GHz
-
The EM-2107A is a standard test fixture for evaluation of the electromagnetic shielding effectiveness of planar material. The fixture is an enlarged section of coaxial transmission line and complies fully with the requirements of ASTM test method D4935-1. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred. The EM-2107A is provided with a reference standard test specimen, a dynamic range specimen. Dynamic range of greater than 80dB is achievable, although the cables and other test system components usually establishes the limiting factors.
-
Product
Antenna, Ridged Guide
EM-6961 | 0.9 GHz – 18 GHz
-
The EM-6961 Double Ridged Guide Antenna is a linearly polarized broadband antenna designed and built specifically for EMI measurements and specification compliance testing.
-
Product
Antenna, Loop Sensor
EM-6873 | 20 Hz – 100 KHz
-
The EM-6873 Loop Sensor Antenna uses passive circuits to transform magnetic field components between 20 Hz – 100 kHz to an equivalent open circuit two-terminal voltage on the receiving instrument. Use of the conversion Factor Chart, supplied with each antenna, will yield the strength of the magnetic induction field referenced to a uniform field. The loop is electrostatically shielded and therefore is sensitive only to the magnetic component (B-field) of the electromagnetic fields.
-
Product
Antenna, Log Periodic
EM-6944 | 200 MHz – 3 GHz
-
The EM-6944 offers an exceptional combination of frequency coverage from 200 MHz – 3 GHz and high power handling capability without compromising the consistent performance versus frequency that makes the log periodic antenna so desirable for test applications.
-
Product
Antenna, Wideband Discone
EM-6115 | 10 KHz – 2 GHz
-
The EM-6115 is a broad band collinear array allowing very wide Omni-Directional frequency coverage in a single package. Below approximately 100 MHz, the EM-6115 acts as an active vertical rod which offers 10 to 12 dB Greater unsaturated instantaneous dynamic range than competitive antennas (overload field strength: 2 V/meter) which greatly reduces intermodulation generated signals in a typical read world RF environment. In the congested spectrum above 100 MHz the antenna is passive and contributes no intermodulation products so the overload point is determined solely by the receiving instrument. This immunity to overload can often make the difference between useful signal output and an indecipherable jumble of spurious products and is accomplished without compromising sensitivity. The antenna collapses for convenient storage and transport.
-
Product
Antenna, Log Periodic
EM-6956-1 | 1 GHz – 2.5 GHz
-
The Electro-Metrics EM-6956-1 Log Periodic Antenna operates over the 1 to 2.5 GHz frequency to range.
-
-
Product
Antenna, Log Periodic
EM-6939 | 800 MHz – 20 GHz
-
The Electro-Metrics EM-6939 Log Periodic Antenna operates over the 800 MHz – 20 GHz frequency range.
-
Product
Probes, Clamp-On
EM-6981 | 9 KHz – 110 MHz
-
Current probes enable you to measure conducted current without direct connection to the circuit under test by clamping around the conductor, current carrying wire or structural member being tested.
-
Product
Probes, Magnetic Field
EM-6881 | 480 KHz To 30 MHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
