Conductivity
-
Product
Total Organic Carbon Monitor
HT-110
-
The continuous online TOC-Analyzer HT-110 is suitable for the measurement ot total organic carbons in Purified Water (PW), Water For Injection (WFI) and Highly Purified Water (HPW). The unit is operating according to USP 643. It is applicable for pharmaceutical and/or semiconductor manufacturing. The measuring principle is based on UV-Oxidation and measurement of the difference in conductivity. TOC concentration measurement (TOC concentration 500 ppbC or lower) is necessary to perform quality control according to GMP (Good Manufacturing Practice).
-
Product
1 kW and 2 kW Laser-Based Floating Zone Furnace
Laser Furnace
-
The 1 kW and 2 kW laser furnace for single crystal fabrication is based on a design and developed in close cooperation with the RIKEN Center for Emergent Matter Science under the leadership of Yoshio Kaneko. Both melting zones have 5 lasers each, which guarantees a high uniformity of power density in the melting zone range. The laser profile has been optimized to reduce thermal stress during the crystal growth process. In addition, the system includes an integrated temperature sensor for real-time temperature monitoring. Temperatures up to 3000 °C can be reached and therefore materials with a very high vapor pressure, a narrow temperature range of the melt, a high thermal conductivity coefficient and incongruent melts can be melted.
-
Product
Bulk Current Monitoring Probe
MP-50
-
The Current Monitoring probes may be used whenever RF current measurements are required. Current measurements are made by placing a current carrying conductor within the “sensing” window of the probe and measuring the probe’s output voltage with an RF detector. Calibration of the probe permits the conversion of the voltages measured to current. Current measurements can be made over the frequency range shown in the transfer impedance curve furnished with each probe. There is virtually no loading of the circuit and the technique permits normal operation of the device under test during measurements. The MP-50 can be used for the procedure for clamp injection when the common- mode impedance requirements cannot be met given in chapter 7.4 of IEC/EN 61000-4-6 „Immunity to conducted disturbances, induced by radio frequency fields”. The MP-50 can also be used as current monitor for BCI testing as per ISO11452-4, RTCA/DO-160 section 20, MIL-STD-461 and various automotive standards.
-
Product
TIM Tester
-
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
-
Product
iBMC Edge Intelligent Solution
Controller
Intelligent board management controller (iBMC) is embedded hardware-based technology that allows administrators to conduct power management remotely.
-
Product
Blockchain Application Testing
-
Blockchain has revolutionized the approach businesses are conducted and provides enterprises the great opportunity to track assets, collaborate and share information. Diverse verticals like retail, finance, and healthcare are reaping the benefits of blockchain distributed ledger technology. The blockchain apps have now gone way beyond crypto-currencies like bitcoin and other decentralized payment modes or systems.
-
Product
Thermal Conductivity Gas Analyzer
CI2000-RQD
-
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
Determining gas concentrations by measuring the thermal conductivity of the gas, CI2000-RQD analyzer uses advanced thermal conductivity sensor with single chip technology. It adopts platinum thread as sense organ to make up Imbalance Bridge, which output signal has a relationship with tested gas volume. And the single chip will magnify, sieve wavelength, modify linearly and criteria the signal by electric procedure.
-
Product
Gas Analyzers
-
Teledyne Analytical Instruments
Gas Analyzers by Teledyne Analytical instruments - carbon dioxide systems, gas chromatographs, hydrocarbon analyzers, infrared analyzers, moisture analyzers, nitrogen analyzers, nitrogen oxides & ammonia analyzers, oxygen analyzers, sulfur analyzers, thermal conductivity analyzers, tunable diode laser (TDL) analyzers, ultraviolet analyzers, and more
-
Product
3U VPX SDR Module
VPX3-ZU1-SDR
-
Sundance Multiprocessor Technology Ltd.
The VPX-ZU1-SDR from PanaTeQ is a 3U OpenVPX module based on a Xilinx Zynq Ultrascale+ MPSoC ZU6EG/ZU9EG/ZU15EG using JESD204B interface to an Analog Devices AD9371 or AD9375 Wideband RF Transceiver. Available in Air Cooled or Conduction Cooled version (see picture), this module offers incredible capabilities for the developers looking for ruggedized Software Defined Radio applications and targeting the defence/aerospace market. The module can work as stand-alone module or can be the SBC of the VPX system using the power effecient Quad-Core ARM Cortex A53 SoC and the on-board PCIe Gen2 Switch (worldwide unique feature)
-
Product
Integrating Spheres
-
Artifex Engineering GmbH & Co. KG
We offer integrating spheres made from a special polymer suitable for the wavelength range 250nm – 2.5 µm. For longer wavelengths in the range 700nm – 20 µm, a gold coating on a rough, metallic surface is used. Since lasers in this spectral range are usually also high power, we use solid copper as a thermally conductive substrate material. By choosing the size of the integrating sphere, the overall sensitivity of the system can be adjusted. In addition, the detector is independent of inhomogeneities in power density and polarization. The detector is also independent of the incidence location and angle of the laser radiation.
-
Product
Rotary Position Sensors
-
We offer a full range of Rotary Position Sensors, in a variety of housings, utilising wirewound, cermet and conductive plastic technology.
-
Product
Portable Conductivity Meter
Starter 300C
-
This portable meter offers convenience, reliability and durability in one compact design.
-
Product
504W - Single Output
PFH Series
-
*2.4" x 4" Brick Footprint with Metal Case*85 - 265VAC Input*12, 28, or 48VDC Output; 12V Aux*High Power Density, High Efficiency*Power Factor Corrected*Suitable for Conduction Cooling*PMBus™
-
Product
Hydrogen Frequency & Time Standard
CH1-1007
-
Hydrogen frequency and time standard Ch1-1007 is designed to generate and reproduce precision, highly stable, spectrally pure frequency and time signals. Main areas of application: – in metrology when transferring the sizes of units of frequency and time, including as part of mobile measuring complexes; – in radio astronomy when conducting scientific research; - in radio navigation when working as part of automated measuring systems and complexes.
-
Product
TDS/Conductivity And PH Testing Instruments
DS & pDS Meters™
-
No water supply is completely pure. Every industrial, commercial, or natural source contains dissolved solids or salts. These impurities contribute to scale, corrosion, poor taste, and environmental pollution that endanger animal and plant life. Myron L® Company has two proven ways to measure such impurities. Our DS Meters™ provide fast, accurate, on-the-spot measurements of total dissolved solids (TDS) or conductivity. pDS Meters™ test conductivity or TDS, plus pH. Readings from their highly stable circuitry help assure product quality, prevent equipment damage and verify in-line instrumentation in a wide range of applications.
-
Product
Universal Transmitter
Model LXT-380
-
Teledyne Analytical Instruments
The Model LXT380 transmitter is a single or dual channel, intelligent, multi-parameter designed for the online continuous measurement of pH, ORP, Specific Ion (pION), dissolved oxygen, free chlorine, total chlorine, conductivity and resistivity. The Model LXT380 Tramsitter digitally communicates with the SP3X digital sensor, automatically configuring the trasmitter's menues and display screens to the measured parameter. The LXT380 tramsitter can be Loop powered or 4-wired DC powered. The standard configuration has a 4-20 mA and a serial communication port with MODBUS RTU output. Alarm relays option is only available on 4-wired DC powered transmitters. LXT380 Transmitter loop is available in FM, ATEX and IECEx certifications.
-
Product
PXI High Density MUX BRIC, 24-Chan, 20-Pole
40-570-313
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
CompactPCI
6U PMC Carrier
-
This conduction cooled 6U CompactPCI dual slot PMC provides an active interface between the CompactPCI bus (backplane) and a PCI Mezzanine Card (PMC). This product addresses the needs of aerospace, military, and rugged applications. It contains a thermal heat frame made of aluminum that fits together with conduction cooled PMC modules. Conduction cooling conducts heat away from the hot spots of the board and transfers the heat to the card edges and to the system chassis. No active ventilation is necessary inside of the system, which means the boards are sealed from the environmental influences found outside of the chassis. The heat frame and integrated wedge locks for the conduction cooling stiffens the carrier and PMC module enabling the board to resist high shock and vibration.
-
Product
Precision Pots Single-turn
-
Precision potentiometers are designed for control applications where accuracy and high-reliability is important. Theses devices are available in conductive plastic, wirewound or Hybritron® element types, and in various sizes. Both single-turn and multiturn models are available.
-
Product
Polymer Aluminum
SP-Cap™
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s industry leading SP-Cap™ Polymer Aluminum Capacitors, are Surface-Mount (SMT) Capacitors that utilize a conductive polymer as their electrolyte material in a layered aluminum design. SP-Cap Capacitors are primarily used as input and output Capacitors for DC/DC converters due to ultra-low ESR values, high voltage options and the ability to withstand high reflow temperatures. These Capacitors are free from temperature drifts, offering capacitance values up to 560µF and voltage values ranging from 2V to 25V.
-
Product
Electromagnetic Flowmeter for conductive liquids
Picomag
-
Reliable measurement and monitoring of industrial water, cooling water or warm water. Simultaneous measurement of flow and temperature. Flexible integration into all fieldbus systems via IO-Link. Commissioning and operation via Bluetooth® and SmartBlue App. Minimum conductivity ≥20 μS/cm. Fluid temperature –10 to +70 °C (+14 to +158 °F).
-
-
Product
Nanomechanical Instruments For SEM/TEM
-
As the world leader in nanomechanical testing systems, Bruker makes it easy for you to conduct in-situ mechanical experiments in your microscope with the Hysitron PI Series PicoIndenters. Our unique transducer design delivers unmatched stability throughout your experiments, resulting in precise data even at the nanoscale. Video capture from the microscope enables real-time monitoring and direct correlation of mechanical data to microscope imaging. With solutions designed to fit many of the microscope brands in use, you are sure to find one that is ideally suited to your research.
-
Product
Monitoring
-
Parker offers a broad range of onsite and laboratory solutions for monitoring, evaluating, and testing a wide variety of substances, from water and hydraulic oil to fuel and various gases, for conditions ranging from insolubility and viscosity levels through flow rate, conductivity, and pressure. They are suitable for use in industrial, marine, and numerous other applications.
-
Product
VPX/open VPX C-Frame 5 Slot 6U
-
Our 2nd Generation C-Frame offers the next level of flexibility in VPX development platforms. Not only can the customer exchange the type of card guides (convection, conduction, AFT) in a blink of an eye but now also the signal backplane. Thanks to Bi=/=Plane®technology, power and signal parts of a VPX backplane are separate PCB assemblies. This enables uncompromised signal quality along with faster turn around for the design of custom profiles.
-
Product
Photometry
-
Photometric equipment is one of our main activities. Two distinct areas are involved - Industrial, Commercial, Road Lighting is one, while Automobile Lighting is another. Photometric equipment areused to conduct tests on Lamps, Industrial Lighting, Street Lighting,Automotive Lighting & related products. Most Photometric equipment are custom built to suit specific customer requirements.
-
Product
Universal Cable/Harness Tester
LX-680
-
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface·Starting up conducts self-diagnosis and self-correction·The system can scan and direct automatically.·The system provides advanced instant open-circuit, short-circuit, continuity test, can test the wire break·It can function as unilateral, standard, multi-segment and spot test of wire·The maximum test voltage is AC1000V / DC1500V·The maximum test spot is 256.
-
Product
RFID Sensor Transponder (HF)
TELID®200
-
With the TELID® 200 range, you can have a combination of RFID transponders and sensors for measuring physical quantities. Here, in particular, pressure, acceleration, strain, moisture, and electric conductivity are of significant interest. Determining the situation just-in-time and storing the newly measured values in the integrated memory is one of its main functions. More complex functions such as digital I/O ports for connecting memories, microcontrollers and digital subsystems are also available. TELID® 200 products do not require batteries and work with no internal energy source.
-
Product
PXI High Density MUX BRIC, 64-Chan, 10-Pole
40-570-414
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Shielded and Unshielded Cable
-
Teledyne Marine Cable Solutions
Shielding Types• Braided I Served I Spiral• Foil & Hybrid• Vapor Barriers• Copper & Alloys• Conductive & Static Dissipative Tapes• Conductive Fabrics• Tensile Members• RFI & EMI Tapes & Braids (Serveor Interwoven)• Utilizing Flat & Round Copper• Stainless Steel• Bronze• Aramid Fibers & Textile, amongothersConstruction• Multi-conductor, shielded pairs, pairs with steel tubed fiber or copper conductors with fiber optics, coaxial conductors & aramid strength fibers
